CDBHM1100L-HF

Low VF SMD Schottky Bridge Rectifiers Reverse Voltage: 20 to 100 Volts Forward Current: 1.0 Amp RoHS Device Halogen Free MBS COMCHIP SMD Diodes Specialist CDBHM120L-HF Thru. CDBHM1100L-HF Features -Ideal for printed cirvuit board -Re liable low cost construction technique results in inexpensive product -High current capability,Low VF -High temperature soldering guaranteed: 260°C / 10 seconds -Pb free product 0.140(0.35) 0.006(0.15) - + 0.157(4.00) 0.276(7.00) MAX 0.142(3.60) 0.083(2.12) 0.043(1.10) 0.008(0.20) MAX 0.102(2.60) 0.087(2.20) 0.043(1.10) 0.028(0.70) 0.053(1.53) 0.037(0.95) 0.193(4.90) 0.177(4.50) 0.053(1.53) 0.037(0.95) 0.106(2.70) 0.090(2.30) Mechanical data -Case: molded plastic -Lead: solder plated -Polarity: As marked 0.033(0.84) 0.022(0.56) 0.118(3.0) MAX Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz resistive or inductive load. For capacitive load, derate current by 20% Parameter Maximum. Repetitive peak reverse voltage Maximum. DC blocking voltage Maximum. RMS voltage Maximum. Instantaneous forward voltage @ 0.5A Average Forward rectified current 0.2*0.2” (5.0*5.0mm)copper pad area ,(see figure 2) Peak Forward surge current,8.3ms single half sine-wave superimposed on Rated Load (JEDEC method) Symbol VRRM VDC VRMS VF IAV CDBHM 120L-HF CDBHM 140L-HF CDBHM 160L-HF CDBHM 180L-HF CDBHM Units 1100L-HF 20 14 20 0.55 40 28 40 60 42 60 0.65 1.0 80 56 80 0.85 100 70 100 V V V V A IFSM 40 A Maximum. DC reverse current @TA=25°C rated DC blocking voltage per leg @TA=100°C Typical thermal resistance(Note 3) IR RθJA RθJL 0.5 20 85 mA °C/W 20 250 -55 to +125 -55 to +150 125 -55 to +150 pF °C °C CJ TJ TSTG Typical junction capacitance(Note 2) Operating temperature range Sorage temperature range Notes: 1.Pulse test: 300µS pulse width, 1% duty cycle. 2.Measured at 1.0MHZ and applied reverse voltage of 4.0 Voltage. 3.Thermal resistance from junction to ambient and from junction to lead P.C.B. mounted on 0.2x0.2” (5.0x5.0mm) copper pad areas. REV: A QW-JL005 Page 1 Comchip Technology CO., LTD. Low VF SMD Schottky Bridge Rectifiers COMCHIP SMD Diodes Specialist RATING AND CHARACTERISTIC CURVES (CDBHM120L-HF Thru. CDBHM1100L-HF) Fig. 1 - Maximum Non-Repetitive Forward Surge Current Per Bridge Elelment 40 1.0 Fig.2 - Maximum Forward Current Derating Curve Average Forward Current, (A) CDBHM180L-HF~ CDBHM1100L-HF Peak Forward Surge Current, (A) 0.8 30 0.6 CDBHM120L-HF ~ CDBHM160L-HF 20 0.4 10 0.2 0 0 1 10 100 0 20 40 60 80 100 120 140 160 Number of Cycles at 60 Hz Ambient Temperature, ( ° C) Fig. 3 - Typical Instantaneous Forward Characteristics Per Bridge Element CDBHM260L-HF Fig. 4 - Typical Reverse Characteristics Per Bridge Element Instantaneous Reverse Current, (mA) 100 Instantaneoys Forward Current, (A) 50 10 CDBHM120L-HF ~ CDBHM140L-HF 10 T J =125 °C 1.0 1.0 CDBHM180L-HF ~ CDBHM1100L-HF 0.1 T J =75 °C 0.1 0.01 T J =25 °C pulse width =300 us 1% duty cycle 0.01 0 0.4 0.8 1.2 1.6 0.001 0 20 40 60 80 100 120 140 Instantaneous Forward Voltage, (Volts) Percent of Rated Peak Reverse Voltage, ( %) REV: A QW-JL005 Page 2 Comchip Technology CO., LTD. Low VF SMD Schottky Bridge Rectifiers Reel Taping Specification P0 P1 d Index hole E T COMCHIP SMD Diodes Specialist - + F B P A W C 12 0 o D2 D1 D W1 Trailer ....... ....... 10 pitches (min) Device ....... ....... ....... ....... Leader ....... ....... 10 pitches (min) End Start Direction of Feed SYMBOL A 5.00 ± 0.01 0.197 ± 0.004 B 7.24 ± 0.10 0.285 ± 0.004 C 2.95 ± 0.10 0.116 ± 0.004 d 1.50 ± 0.10 0.059 ± 0.004 D 330.0 13.00 D1 50.0 MIN. 1.969 MIN. D2 13.0 ± 0.20 0.512 ± 0.008 MBS (mm) (inch) SYMBOL E 1.75 ± 0.10 0.069 ± 0.004 F 5.50 ± 0.05 0.217 ± 0.002 P 8.00 ± 0.10 0.315 ± 0.004 P0 4.00 ± 0.10 0.157 ± 0.004 P1 2.00 ± 0.05 0.079 ± 0.002 W 12.00 ± 0.30 0.472 ± 0.012 W1 12.0~14.40 0.472~0.657 MBS (mm) (inch) REV: A QW-JL005 Page 3 Comchip Technology CO., LTD. Low VF SMD Schottky Bridge Rectifiers COMCHIP SMD Diodes Specialist Marking Code Part Number CDBHM120L-HF CDBHM140L-HF CDBHM160L-HF CDBHM180L-HF CDBHM1100L-HF Marking Code MBSK12SE MBSK14SE MBSK16SE MBSK18SE MBSK110SE + MBSKxxSE xx/xxx = Product type marking code Suggested PAD Layout MBS SIZE (mm) A B C D 3.30 0.90 1.84 6.00 (inch) 0.130 0.035 0.072 0.236 D B C A Standard Package Qty per Reel Case Type (Pcs) MBS 2500 Reel Size (inch) 13 REV: A QW-JL005 Page 4 Comchip Technology CO., LTD.