15-006303

F E D C B AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. A (5:1) n1,16 (15x) SEALING COMPOUND D 10,69 +- 0,4 0,3 D 39,22 +- 0,3 0,15 2,55 +- 0,25 0 33,32 +- 0,13 0,12 SEALING GASKET 12,8 +- 0,3 0,15 24,79 +- 00,25 5,78 +- 0,17 0,08 b 8 +- 0,02 0,23 b 10° C C 15-00630o CONEC ABC 4-40 UNC 9,4 4,6 SEE NOTE 12 SW 4,8 4-40 UNC B B c NOTES: RoHS compliant F E DO NOT ALTER CAD DRAWING BY HAND A THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST; min. 50µin NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0; BLACK 6. SEALING GASKET: SILICONE; BLUE 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0; BLACK 8. CONTACTS: COPPER ALLOY; PLATING (SEE PART-NO.): o PLEASE ADD 1 for 30µin HARD GOLD over min. 50µin NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL SOLDER CUP ACCEPTS CABLE AWG 20 9. HEXLOCKING SCREWS: STAINLESS STEEL 10. RECOMMENDED PANEL CUT-OUT ON SHEET 2 11. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 12. CONNECTOR IS PART MARKED: 15-00630o CONEC ABC (see note 8) scale: material: tolerance 2:1 (5:1) SEE NOTES dim. in mm date drawn 29.09.14 appd. 26.01.15 A title: name Lehmenkühler D-SUB FEMALE Fischer 15pos. SOLDER CUP with closed 4-40 UNC thread norm 1xc Ä5827 24.09.15 Unkrüer d-old 2xb Ä5817 15.09.15 dwg no: M.H. a Original rev. description D date part no: name C DINA3 sh: 1 15K1A1537 R B 15-00630o (see note 8) A F E c D C B A Solder Instruction D D 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350°C, 50 Watt max. and use a pencil tip. 4. Apply some solder to the solder tip of the soldering iron. 5. Put tip to wire in solder cup. 6. After 1 second bring in solder. 7. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 8. Remove soldering iron. 9. Wait until solder gets rigid again. 10. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C RECOMMENDED PANEL CUT-OUT 28,8 `0,1 i 0,26 A 11,4 `0,1 B B R3 n3,1 `0,05 (2x) B i 0,26 B ,4 ` 10° `1° 3 0,1 33,32 `0,1 A F E DO NOT ALTER CAD DRAWING BY HAND THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH A scale: material: tolerance 5:1 SEE SHEET 1 dim. in mm date drawn 29.09.14 appd. 26.01.15 Lehmenkühler RECOMMENDED PANEL CUT-OUT Fischer D-SUB FEMALE 15pos. SOLDER CUP with closed 4-40 UNC thread dwg no: DIN- norm d-old 1xc Ä5827 a Original A title: name 24.09.15 Unkrüer rev. description D date part no: name C A3 sh: 2 15K1A1537 R B SEE SHEET 1 A