15K1A262

F E D C B A b NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST; min. 50µin NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0, BLACK 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0; BLACK 8. CONTACTS: COPPER ALLOY PLATING (SEE PART NO): o PLEASE ADD 1 for 30µin HARD GOLD over min. 50µin NICKEL o PLEASE ADD 3 for 8µin HARD GOLD over min. 50µin NICKEL SOLDER CUP ACCEPTS CABLE AWG 20 9. HEXLOCKING SCREWS: STAINLESS STEEL 10. RECOMMENDED PANEL CUT-OUT ON SHEET 2 11. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max.67Ncm (6 in.LB) 12. CONNECTOR IS PART MARKED: 15-00062o CONEC ABC n1,16 (15x) D (5:1) D 10,34 + 0,4 - 0,3 c 0,17 6,13 + 0,08 - 3,6 + 0,25 -0 8 + 0,23 47,7 + 0,3 -0 33,32 + 0,13 - 0,12 C 0,02 c 24,79 + 0 - 0,25 C 21,1 + 0,3 -0 10° SEALING COMPOUND O-RING B 15-00062o CONEC ABC B SEE NOTE 12 b 4,6 9,4 4-40 UNC 4-40 UNC c SW 4,8 AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL CUSTOMER APPROVAL DATE: DO NOT ALTER CAD DRAWING BY HAND tolerance dim. in mm date drawn appd. norm scale: material: title: 2:1 (5:1) APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION see notes A A name NAME: TITLE: 08.09.08 15.09.08 Schmidt Fischer D-SUB FEMALE 15pos. SOLDER CUP with hexlocking screw dwg no: R COMPANY NAME: 3xc 3xb a Ä 3435 Ä 3129 Origin 30.09.09 26.09.08 HS Petker d-old Inventor 10 15K1A262 part no: B A DINA3 sh: 1 APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL rev. description D date name C 15-00062o (see note 8) b F E F E D C B A D b D Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350°C, 50 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C RECOMMENDED PANEL CUT-OUT b i 0,26 A 28,8 `0,1 B B 11,4 `0,1 B n3,1 `0,05 (2x) ,4 ` R3 10° `1° i 0,26 B 3 0,1 33,32 `0,1 A THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL CUSTOMER APPROVAL DATE: DO NOT ALTER CAD DRAWING BY HAND tolerance dim. in mm date drawn appd. norm d-old scale: material: title: 5:1 see sheet 1 A APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION A name NAME: TITLE: 08.09.08 15.09.08 Schmidt Fischer PANEL CUT-OUT D-SUB FEMALE 15pos. SOLDER CUP with hexlocking screw dwg no: Inventor 10 DINR COMPANY NAME: 2xb a Ä 3129 Origin 26.09.08 Petker 15K1A262 part no: A3 sh: 2 A APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL rev. description D date name C see sheet 1 F E B