15K1A299

F E D C B A NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMERATURE 265°C FOR 8 SEC. AND SOLDER PREHEAT 150°C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER HIGH TEMPERATURE EXPOSURE 4. METALSHELL: ZINC DIE CAST; min. 50µin NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0, BLACK 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A 7. RUBBER GASKET: TPE 8. SEALING COMPOUND: EPOXY RESIN UL 94 V-0; BLACK 9. CONTACTS: COPPER ALLOY PLATING (SEE PART NO): o PLEASE ADD 1 for 30µin HARD GOLD over min. 50µin NICKEL o PLEASE ADD 3 for 8µin HARD GOLD over min. 50µin NICKEL 10. METAL BRACKETS: ZINC DIE CAST; 300µin COPPER/40-120µin NICKEL/120-200µin TIN 11. WASHERS: COPPER ALLOY; 80µin NICKEL 12. HEXLOCKING SCREWS: STAINLESS STEEL 13. PCB-SNAPS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL PCB-HOLE: n3.1`0.1; PCB THICKNESS 1.6mm 14. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 15. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max.67Ncm (6 in.LB) 16. CONNECTOR IS PART MARKED: 15-00075o CONEC ABC c n0,6 `0,05 (25x) 4,85 `0,3 6,35 `0,3 D D (5:1) 13,07 + 0,4 - 0,3 13,5 + 0,4 - 0,3 10,75 + 0,4 - 0,3 0,4 10,23 + 0,3 - c 0 5,99 + 0,3 - 3,6 + 0,25 -0 8,23 + 0,25 -0 C C 61,4 + 0,3 -0 POS. 1 POS. 14 47,04 `0,13 38,86 + 0,23 - 0,02 c RUBBER GASKET PLACED ON TOP SURFACE OF MALE INSULATOR 21,1 + 0,3 -0 10° B PRESS FOR FIXING ON PCB METAL BRACKET 3,2 `0,2 B SEALING COMPOUND O-RING 15-00075o CONEC ABC PCB SNAP SEE NOTE 16 c 4,6 AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 4-40 UNC 9,4 4-40 UNC APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION SW 4,8 scale: material: title: 2:1 (5:1) APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL CUSTOMER APPROVAL DATE: DO NOT ALTER CAD DRAWING BY HAND tolerance dim. in mm date drawn appd. norm d-old APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION see notes A A name NAME: TITLE: 17.10.08 23.10.08 Schmidt Fischer D-SUB MALE 90° 25pos. SOLDER PIN ANGLED with metal bracket, hexlocking screw and snap dwg no: Inventor 10 DINR COMPANY NAME: 4xc a Ä 3435 Origin 02.10.09 HS 15K1A299 part no: A3 sh: 1 (see note 9) A APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL rev. description D date name C 15-00075 o F E B F E D C B A P.C.B. HOLE DRILLINGS 47,04 `0,13 D D 16,56 `0,1 13,82 `0,1 11,05 `0,1 8,28 `0,1 5,54 `0,1 n3,1 `0,1 (2x) 1 2,77 `0,1 10,75 6,85 1,4 `0,1 4,14 `0,1 C b c P.C.B. EDGE FRONTPANEL 2,84 `0,1 + 0,1 n1 - 0 (25x) 6,33 `0,1 b c C 6,91 `0,1 9,68 `0,1 12,42 `0,1 15,19 `0,1 RECOMMENDED PANEL CUT-OUT i 0,26 A B 42,5 `0,1 B B n3,1 `0,05 (2x) 11,4 `0,1 ,4 ` R3 10° `1° i 0,26 B 0, 1 3 47,04 `0,1 A THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL CUSTOMER APPROVAL DATE: DO NOT ALTER CAD DRAWING BY HAND tolerance dim. in mm date drawn appd. norm scale: material: title: 4:1 see sheet1 A APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION A name NAME: TITLE: 17.10.08 23.10.08 Schmidt Fischer P.C.B HOLE DRILLINGS PANEL CUT-OUT D-SUB Male 25pos. Solder pin angled 90° dwg no: Inventor 10 DINR COMPANY NAME: 2xc 2xb a Ä 3435 Ä 3344 Origin 02.10.09 15.04.09 HS HS d-old 15K1A299 part no: A3 sh: 2 A APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL rev. description D date name C see sheet 1 F E B