163C50009X

12 11 .025 0.64 10 9 7 8 OPTIONAL VOIDED CIRCUIT SEE CHART FOR LOCATIONS TYP 5 6 4 CKTS .096 2.45 .118 ±.004 3.00 ±0.10 NON-ACCUM. .115 TYP 2.92 H 2 B ±0.004 B ±0.10 .050 TYP 1.27 LAST CIRCUIT 3 2 CIRCUIT 1 3 NOTE 9 4 .128 3.25 .273 ±.003 6.93 ±0.08 5 NOTE 9 6 .063 1.60 ⌀ .095 ±.002 2.41 ±0.05 DIA TYP SEE NOTE 6 G 7 8 .030 0.75 .085 ±.002 2.15 ±0.05 A B .047 1.20 .118 3.00 TYP F 9 C ±0.003 C ±0.08 .390 9.90 10 PCB LAYOUT: COMPONENT SIDE RECOMMENDED PCB THICKNESS: .062/1.57 11 12 NOTE 9 .172 4.37 NOTE 9 CIRCUIT 1 E .08 2.0 .18 4.6 .400 MAX 10.16 NOTES: 1. HOUSING MATERIAL: LIQUID CRYSTAL POLYMER, GLASS FILLED, UL94V-0, COLOR: BLACK TERMINAL MATERIAL: BRASS ALLOY FINISH A CKTS MATERIAL NO: B FINISH MATERIAL NO: VOID CKT MATERIAL NO: 43650-0210 43650-0211 03 43650-0309 43650-0310 43650-0311 04 43650-0409 43650-0410 43650-0411 05 43650-0509 43650-0510 43650-0511 06 43650-0609 43650-0610 43650-0611 07 43650-0709 43650-0710 43650-0711 08 43650-0809 43650-0810 43650-0811 C = .000030/(0.00076) MIN. SELECT GOLD IN CONTACT AREA .000100/(0.00254) MIN. SELECT MATTE TIN ON SOLDER TAILS BOTH OVER .000050/(0.00127) NICKEL OVERALL 09 43650-0909 43650-0910 43650-0911 10 43650-1009 43650-1010 43650-1011 3. PRODUCT SPECIFICATION: PS-43650 4. TAPE & REEL PACKAGED PER MOLEX DRAWING 436500001-PK 5. MATES WITH: RECEPTACLE NUMBER 43645 11 43650-1109 43650-1110 43650-1111 12 43650-1209 43650-1210 43650-1211 B = .000015/(0.00038) MIN. SELECT GOLD IN CONTACT AREA .000100/(0.00254) MIN. SELECT MATTE TIN ON SOLDER TAILS BOTH OVER .000050/(0.00127) NICKEL OVERALL 03 6. TO MINIMIZE INSERTION FORCE ON MOUNTING CLIPS DURING ROBOTIC PLACEMENT, HOLE DIAMETER SPECIFICATIONS MUST BE INCREASED MAKING THEM MORE COMPATIBLE WITH PICK AND PLACE EQUIPMENT. HOLE DIAMETERS SHOULD BE INCREASED TO APPROXIMATELY .100±.002/(2.54±0.05) AND EVALUATED PER PLACEMENT EQUIPMENT. 04 SYMBOLS = 0 = 0 SCALE IN/MM NTS = 0 = 0 20:36:14 C 8 7 .691 17.56 MM 6 INCH 4 PLACES ± ± 3 PLACES ± ± 0.01 2 PLACES ± 0.25 ± 0.014 ± 0.36 ± = 0 1 PLACE = 0 0 PLACES ± = 0 C MATED MICRO FIT CONNECTORS 02 B CURRENT REV DESC: ADD KEEP OUT AREAS TO PCB LAYOUT; ADD NOTE 12 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 = 0 9 F THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS ANGULAR TOL 2020/10/02 10 G D 02 43650-1410 8. TO AVOID INTERFERENCE BETWEEN RECEPTACLE AND PCB, HEADER MUST BE PLACED WITHIN .400/(10.16) MAX. FROM EDGE OF PCB, AS SHOWN IN LOCATION DETAIL. 9. METAL TAB MAY BE FLUSH WITH PCB. NO EXPOSED TRACES OR VIAS ALLOWED NEAR THESE AREAS. 10. PARTS CONFORM TO CLASS 'B' REQUIREMENTS OF COSMETIC SPECIFICATION PS-45499-002. 11. TEXT ON PART IS FOR REFERENCE ONLY. TEXT AND TEXT LOCATION MAY VARY DEPENDING ON PART NUMBER AND/OR TOOL. 12. HOLES FOR CLIPS SHOULD BE PTH AND CLIPS SHOULD BE SOLDERED FOR BEST RETENTION TO PCB. RELEASE DATE 11 VOID CKT 43650-1311 7. THE COPLANARITY DIMENSION IS ESTABLISHED BY PLACING THE ASSEMBLY ON A FLAT SURFACE. THE DISTANCE FROM THAT SURFACE TO THE BOTTOM OF ANY ANY TERMINAL MUST NOT EXCEED .006/0.15 P1 H C 43650-0209 DOCUMENT STATUS 12 .287 7.30 .405 10.30 .524 13.30 .642 16.30 .760 19.30 .878 22.30 .996 25.30 1.114 28.30 1.232 31.30 1.350 34.30 1.469 37.30 SEE NOTE 7 02 A = .000060/(0.00152) MIN. REFLOWED MATTE TIN OVER .000050/(0.00127) MIN. NICKEL (FINISH IS BRIGHT IN APPEARANCE, THICKNESS AS APPLIED PRIOR TO REFLOW) FORMAT: Eng-lega-master-tb-prod-C REVISION: D DATE: 2018/01/18 .118 3.00 .236 6.00 .354 9.00 .472 12.00 .591 15.00 .709 18.00 .827 21.00 .945 24.00 1.063 27.00 1.181 30.00 1.299 33.00 RECEPTACLE #43645 COPLANARITY DETAIL LOCATION DETAIL FINISH 2. FINISH: A .380 9.65 .498 12.65 .616 15.65 .734 18.64 .852 21.64 .970 24.64 1.088 27.64 1.206 30.63 1.325 33.66 1.443 36.65 1.561 39.65 DIM C E SEE NOTE 8 B DIM B .08 2.0 REF .42 10.7 C DIM A .006 MAX 0.15 LAST CIRCUIT D 1 ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 637806 2020/05/07 2020/10/01 2020/10/02 DRWN: BZAPPA CHK'D: SSOUSEK APPR: FSMITH INITIAL REVISION: DRWN: SAMIEC APPR: FSMITH THIRD ANGLE PROJECTION 4 MICRO FIT (3.0) RIGHT ANGLE SMT CLIPS SINGLE ROW / TAPE AND REEL PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2000/07/07 2016/03/18 DRAWING SERIES C-SIZE 43650 3 SD-43650-004 MATERIAL NUMBER PSD 000 CUSTOMER SEE CHART 2 E2 SHEET NUMBER GENERAL MARKET 1 OF 1 1 A