6225-10.00M

5.0V HCMOS Surface Mount Crystal Clock Oscillator 6215, 6225, 6235 XO 2111 Comprehensive Drive 2111 Comprehensive Drive Aurora, Illinois 60505 Aurora, Illinois 60505 Phone: 630- 851- 4722 Phone: 630- 851- 4722 Fax: 630- 851- 5040 Fax: 630- 851- 5040 www.conwin.com www.conwin.com Features: The Connor-Winfield models 6215, 6225, and 6235 are a 6 x 3.5mm, 5.0V HCMOS, Ceramic, Surface Mount, Fixed Frequency Crystal Oscillators (XO) designed for use in all applictions requiring precision clocks. The RoHS compliant, surface mount package is designed for high-density mounting and is optimum for mass production. 1.8 to 50 MHz 5.0V Operation RoHS Compliant Tri-State Enable / Disable Function Overall Frequency Tolerance: 6215 ± 25 ppm 6225 ± 50 ppm 6235 ± 100 ppm Temperature Range: -40 to 85°C Ceramic Surface Mount Package Tape and Reel Packaging US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Minimum -55 -0.5 Nominal Maximum 125 7.0 Units °C Vdc Notes Operating Specifications Parameter Frequency Range (Fo) Frequency Tolerance 6215 6225 6235 Operating Temp Range Supply Voltage (Vdd) Supply Current (Icc) 1.8 to 31.999 MHz 32.0 to 50.0 MHz Minimum 1.8 -25 -50 -100 -40 4.50 Nominal 5.0 Maximum 50 25 50 100 85 5.50 27 45 Units MHz ppm Notes 1 °C Vdc mA Input Characteristics Parameter Enable Voltage - (Vih) Disable Voltage - (Vil) Enable Time Disable Time Minimum 2.2 Nominal Maximum 0.8 100 100 Units Vdc Vdc nS nS Notes 2 HCMOS Output Characteristics Parameter Load (Voh) Voltage High (Vol) Low (loh) Current High (lol) Low Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Start-Up Time Jitter Notes: 1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging. 2. Oscillator output is enabled with no connection on pad 1 Bulletin Page Revision Date Sm084 1 of 2 01 30 May 2002 Minimum 4.50 -16 40 - Nominal 50 - Maximum 50 0.55 16 60 5 10 5 Units pF Vdc mA % nS mS pS RMS Notes Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Package Characteristics Package Hermetically sealed ceramic package and metal cover Suggested Pad Layout Environmental Characteristics Temperature Cycle The specimen shall meet electrical characteristics after tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes Hermetical No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes Solvent Resistance Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene Soldering General Conditions 260°C max x 10 sec max x 2 times max or 230°C max x 180 sec max x 1 time Typical Operation Data (Vapor phase reflow) 20 to 100 sec up to 215°C, 50 sec at 215°C, then down to room temperature per 1 to 5°C / sec Bypass capacitor, C-by, should be ceramic capacitor ≥ .01uf. Test Circuit OSCILLOSCOPE PROBE Mechanical Characteristics Free Drop The specimen shall meet electrical characteristics after tested 3 times, Free Drop testing on the hard wooden board from a height of 75 cm. Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, 55-2000 Hz 20 G's, 2 hours for each plane Thermal Shock After applied Thermal Shock of 260°C max x 10 sec max x 2 times, or 230°C max x 180 sec max, the specimen shall meet electrical characteristics Solderability (EIAJ-RCX-0102.101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235°C ±5°C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec ±0.5 sec into solder bath After performing the above procedures, a newly soldered coverage shall be greater than 90% POWER SUPPLY OSC FREQ COUNTER INPUT FOR E/D Output Waveform TF 90% 50% TR Pad 1: 2: 3: 4: Connection Tri-State E/D Ground Output VDD 10% GND. LEVEL T0 = 1/ fo T1 SYMMETRY=(T1/T0)X100% Dimensional Tolerance: ±.008 (.20mm) Ordering Information Tape and Reel Dimensions 6215 CLOCK SERIES - 10.00 MHz CENTER FREQUENCY Bulletin Page Meets EIA-481A and EIAJ-1009B 3,000 PCS/Reel Dimensional Tolerance: ±.02" (.508mm) ±.005"(.127mm) Revision Date Sm084 2 of 2 01 30 May 2002 Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation