5.0V HCMOS Surface Mount Crystal Clock Oscillator 7115, 7125, 7135
XO
2111 Comprehensive Drive 2111 Comprehensive Drive Aurora, Illinois 60505 Aurora, Illinois 60505 Phone: 630- 851- 4722 Phone: 630- 851- 4722 Fax: 630- 851- 5040 Fax: 630- 851- 5040 www.conwin.com www.conwin.com
Features:
The Connor-Winfield models 7115, 7125, and 7135 are a 5 x 3.2mm, 5.0V HCMOS, Surface Mount, Fixed Frequency Crystal Oscillators (XO) designed for use in all applictions requiring precision clocks. The RoHS compliant, surface mount package is designed for high-density mounting and is optimum for mass production. 1.8 to 50 MHz 5.0V Operation RoHS Compliant Tri-State Enable / Disable Function Overall Frequency Tolerance: 7115 ± 25 ppm 7125 ± 50 ppm 7135 ± 100 ppm Temperature Range: 0 to 70°C Ceramic Surface Mount Package Tape and Reel Packaging
US Headquarters: 630-851-4722 European Headquarters: +353-61-472221
Absolute Maximum Ratings
Parameter Storage Temperature Supply Voltage (Vcc) Minimum -55 -0.5 Nominal Maximum 125 7.0 Units °C Vdc Notes
Operating Specifications
Parameter Frequency Range (Fo) Frequency Tolerance 7115 7125 7135 Operating Temp Range Supply Voltage (Vdd) Supply Current (Icc) Minimum 1.8 -25 -50 -100 0 4.5 Nominal 5.0 Maximum 50 25 50 100 70 5.5 45 Units MHz ppm Notes 1
°C Vdc mA
Input Characteristics
Parameter Enable Voltage - (Vih) Disable Voltage - (Vil) Enable Time Disable Time Minimum 2.2 Nominal Maximum 0.8 100 100 Units Vdc Vdc nS nS Notes 2
HCMOS Output Characteristics
Parameter Load (Voh) Voltage High (Vol) Low (loh) Current High (lol) Low Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Start-Up Time Jitter
Bulletin Page Revision Date
Minimum 4.50 -16 40 -
Nominal 50 -
Maximum 50 0.55 16 60 5 10 5
Units pF Vdc mA % nS mS pS RMS
Notes
Sm088 1 of 2 01 20 June 2002
Notes:
1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging. 2. Oscillator output is enabled with no connection on pad 1
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com
Package Characteristics
Package Hermetically sealed ceramic package and metal cover
Suggested Pad Layout
Environmental Characteristics
Temperature Cycle The specimen shall meet electrical characteristics after tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes Hermetical No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes Solvent Resistance Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene
Soldering
General Conditions 260°C max x 10 sec max x 2 times max or 230°C max x 180 sec max x 1 time Typical Operation Data (Vapor phase reflow) 20 to 100 sec up to 215°C, 50 sec at 215°C, then down to room temperature per 1 to 5°C / sec
Bypass capacitor, C-by, should be ceramic capacitor ≥ .01uf.
Test Circuit
OSCILLOSCOPE
Mechanical Characteristics
Free Drop The specimen shall meet electrical characteristics after tested 3 times, Free Drop testing on the hard wooden board from a height of 75 cm. Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, 55-2000 Hz 20 G's, 2 hours for each plane Thermal Shock After applied Thermal Shock of 260°C max x 10 sec max x 2 times, or 230°C max x 180 sec max, the specimen shall meet electrical characteristics Solderability (EIAJ-RCX-0102.101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235°C ±5°C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec ±0.5 sec into solder bath
After performing the above procedures, a newly soldered coverage shall be greater than 90%
POWER SUPPLY
PROBE
OSC
FREQ COUNTER
INPUT FOR E/D
Output Waveform
Pad 1: 2: 3: 4:
Connection Enable / Disable Ground Output Vcc
SYMMETRY
Dimensional Tolerance: ± .02" (.508mm) ± .005" (.127mm)
Tape and Reel Dimensions
Ordering Information
7115
CLOCK SERIES
-
20.00 MHz
CENTER FREQUENCY
Dimensional Tolerance: ±.02" (.508mm) Dimensional Tolerance: ±.02” (. ±.005” (. ±.005" (.127mm)
Bulletin Page
Meets EIA-481A and EIAJ-1009B 2,000 PCS/REEL
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
Revision Date
Sm088 2 of 2 01 20 June 2002
很抱歉,暂时无法提供与“7115”相匹配的价格&库存,您可以联系我们找货
免费人工找货- 国内价格
- 1+1.08339
- 100+1.01116
- 300+0.93894
- 500+0.86671
- 2000+0.8306
- 5000+0.80893
- 国内价格
- 1+0.1176
- 100+0.10976
- 300+0.10192
- 500+0.09408
- 2000+0.09016
- 5000+0.08781
- 国内价格
- 5+0.14116
- 20+0.12892
- 100+0.11668
- 500+0.10444
- 1000+0.09873
- 2000+0.09465
- 国内价格
- 1+0.16602
- 100+0.15523
- 300+0.14445
- 500+0.13367
- 2000+0.12828
- 5000+0.12505
- 国内价格
- 1+0.25536
- 10+0.23572
- 30+0.23179
- 100+0.22
- 国内价格
- 5+0.36958
- 20+0.33697
- 100+0.30436
- 500+0.27175
- 1000+0.25653
- 2000+0.24566
- 国内价格
- 50+0.01229
- 500+0.01116
- 5000+0.00965
- 30000+0.00927
- 90000+0.0089
- 国内价格
- 50+0.01356
- 500+0.0122
- 5000+0.0113
- 10000+0.01085
- 30000+0.0104
- 50000+0.01012
- 国内价格
- 50+0.00553
- 500+0.00502
- 5000+0.00434
- 30000+0.00417
- 90000+0.004
- 国内价格
- 50+0.0081
- 500+0.00736
- 5000+0.00636
- 30000+0.00612
- 90000+0.00587