5.0V Surface Mount
Crystal Clock Oscillator
HSM9
Features:
XO
2111 Comprehensive Drive
2111 Comprehensive Drive
Aurora, Illinois 60505
Aurora, Illinois 60505
Phone: 630- 851- 4722
Phone: 630- 851- 4722
Fax: 630- 851- 5040
Fax: 630- 851- 5040
www.conwin.com
www.conwin.com
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
The Connor-Winfield HSM91, HSM92,
HSM93, and HSM94 models are
7.5mm x 5mm, 5.0V HCMOS, Surface Mount,
Fixed Frequency Crystal Oscillators (XO)
designed for use in all applications requiring
precision clocks. The RoHS compliant surface
mount package is designed for high-density
mounting and is optimum for mass
production.
1.0 to 80 MHz
5.0V Operation
RoHS Compliant
Tri-State Enable / Disable
Overall Frequency Tolerance:
HSM94 ± 20 ppm,
HSM91 ± 25 ppm
HSM92 ± 50 ppm,
HSM93 ± 100 ppm
Temperature Range: 0 to 70°C
Ceramic Surface Mount Package
Tape and Reel Packaging
Absolute Maximum Ratings
Parameter
Storage Temperature
Supply Voltage (Vcc)
Minimum
-55
-0.5
Parameter
Frequency Range (Fo)
HSM94
HSM91
HSM92
HSM93
Frequency Tolerance
HSM94
HSM91
HSM92
HSM93
Operating Temp Range
Supply Voltage (Vdd)
Supply Current (Icc)
1.0 to 31.999 MHz
32 to 49.999 MHz
50 to 80.0 MHz
Minimum
Nominal
-
Maximum
125
7.0
Units
°C
Vdc
Notes
Units
MHz
Notes
ppm
1
Operating Specifications
1.8
1.0
1.0
1.0
-20
-25
-50
-100
0
4.5
-
Nominal
-
-
5.0
-
Maximum
80
20
25
50
100
70
5.5
27
45
75
°C
Vdc
mA
Input Characteristics
Parameter
Enable Voltage - (Vih)
Disable Voltage - (Vil)
Enable Time
Disable Time
Minimum
≥ 70% Vdd
-
Nominal
-
Maximum
≤ 30% Vdd
100
100
Units
Vdc
Vdc
mS
nS
Notes
2
Units
pF
Notes
HCMOS Output Characteristics
Bulletin
Page
Revision
Date
Sm006
1 of 2
27
07 May 2008
Parameter
Load
(Voh)
Voltage High
Low (Vol)
(loh)
Current High
Low (lol)
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
Start-Up Time
Jitter
Minimum
4.5
-16
45
-
Nominal
50
-
Maximum
50
0.55
16
55
6
10
5
Vdc
mA
%
nS
mS
pS RMS
Notes:
1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging.
2. Oscillator output is enabled with no connection on pad 1
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Package Characteristics
Package
Suggested Pad Layout
Hermetically sealed ceramic package and metal cover
Environmental Characteristics
Temperature Cycle
The specimen shall meet electrical characteristics after
tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes
Hermetical
No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes
Solvent Resistance
Marking will withstand immersion in
Isopropyl Alcohol or Trichloroethylene
Soldering
General Conditions 260°C max x 10 sec max x 2 times max or
230°C max x 180 sec max x 1 time
Typical Operation Data
(Vapor phase reflow)
20 to 100 sec up to 215°C, 50 sec
at 215°C, then down to room temperature per 1 to 5°C / sec
Mechanical Characteristics
Bypass capacitor, C-by, should be
ceramic capacitor ≥ .01 uf
Test Circuit
OSCILLOSCOPE
Vcc
PROBE
POWER
SUPPLY
Free Drop
The specimen shall meet electrical characteristics after tested 3 times,
Free Drop testing on the hard wooden board from a height of 75 cm.
Vibration
The specimen shall meet electrical characteristics after tested
by the following conditions: 10-55Hz 1.5mm Amplitude,
55-2000 Hz 20 G's, 2 hours for each plane
Thermal Shock
After applied Thermal Shock of 260°C
max x 10 sec max x 2 times, or 230°C max x 180 sec max,
the specimen shall meet electrical characteristics
Solderability
(EIAJ-RCX-0102.101 Condition 1a)
1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%)
2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%)
3) Solder bath temperature: 235°C ±5°C
4) Depth of immersion: Up to electrical terminal
5) Immersing time: Within 2 sec ±0.5 sec into solder bath
.01uf
OSC
FREQ
COUNTER
INPUT FOR E/D
Output Waveform
After performing the above procedures, a newly soldered coverage shall be greater than 90%
SYMMETRY
Pin Connections
1: Tri-State E/D
2: Ground
3: Output
4: VDD
Tape and Reel Dimensions
Ordering Information
HSM91
-
050.0M
CLOCK
SERIES
CENTER
FREQUENCY
Dimensional Tolerance: ±.02" (.508mm)
±.005"(.127mm)
Bulletin
Page
Meets EIA-481A and EIAJ-1009B
2,000 PCS/Reel
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
Revision
Date
Sm006
2 of 2
27
07 May 2008
很抱歉,暂时无法提供与“HSM93-050.0M”相匹配的价格&库存,您可以联系我们找货
免费人工找货