OFC5DJ3BS-10.00M

THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS OFC5DJ3BS CW 0534 SURFACE MOUNT 5.0V OCXO with SINEWAVE OUTPUT ABSOLU TE MAX IMUM RATING S PARAMETER Storage Temperature Supply Voltage UNITS (Vcc) MINIMUM -40 -0.5 NOMINAL M AXIMUM 85 7 UNITS °C Vdc TABLE 1.0 NOTE OFC5DJ3BS DESCRIPTION OPERATING SPECIFIC ATIONS PARAMETER Center Frequency Standard Frequencies Available: Frequency Calibration Frequency vs. Temperature Stability Frequency vs. Voltage Stability (+/ -5%) Frequency vs. Load Stability (+/-5%) Aging: Daily Aging: First Year Aging: Long Term (20 Years) Total Frequency Tolerance (20 years) Allen Variance: 1 second, 100 average. Operating Temperature Range Supply Voltage Power Consumption: Turn On Power Consumption: Steady-State Start-Up Time Warm Up (Fo) MINIMUM 10 NOMINAL M AXIMUM 20 UNITS MHz TABLE 2.0 NOTE 1 2 3 (Vcc) 10 MHZ, 13 MHz, 15 MHZ, or 20 MHz -0.2 0.2 ppm -20 20 ppb -2 2 ppb -2 2 ppb -1 1 ppb/day -50 50 ppb -250 250 ppb -500 500 ppb 1.00E-10 RMS -20 70 °C 4.75 5.00 5.25 Vdc 3.75 W 1. 5 W 500 mS -100 100 ppb 4 5 The Connor-Winfield OFC5DJ3BS is a 5V Surface Mount Oven Controlled Crystal Oscillator (OCXO) with a Sinewave output. The OFC5J3BS is designed for Wireless applications requiring low Phase Noise and tight frequency stability. 6 6 7 8 TABLE 3.0 FEATURES SINEWAVE OUTPUT CHARACTERISTICS PARAMETER LOAD Output Power Spurious Output SSB Phase Noise at 1Hz offset SSB Phase Noise at 10Hz offset SSB Phase Noise at 100Hz offset SSB Phase Noise at 1KHz offset SSB Phase Noise at 10KHz offset MINIMUM 45 0 NOMINAL 50 3 -85 -110 -135 -150 -155 M AXIMUM 55 -80 UNITS Ohms dBm dBc dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz NOTE FIXED FREQUENCY OCXO FREQUENCY STABILITY: ±20ppb TEMERATURE RANGE: -20 to 70°C 5.0V OPERATION SINEWAVE OUTPUT RESTABILIZATION TIME Off Time < 1 Hour < 6 Hours < 24 Hours 1 to 16 Days > 16 Days Restabilization Time < 2 Hours < 12 Hours < 48 Hours 48 Hours + ¼ Off Time < 6 Days TABLE 4. 0 NOTE 9 9 9 9 9 LOW PHASE NOISE SURFACE MOUNT PACKAGE TAPE AND REEL PACKAGING PACKAG E CHARACTERISTICS Package TABLE 5.0 Non-hermetic package consisting of an FR4 substrate with grounded metal cover. ENVIRONMNETAL CHARACTERISTICS TABLE 6.0 Shock 100G’s, 6mS, halfsine per MIL-STD-202F, Method 213B, Test Condition C Vibration 0.06” D.A. or 10G peak 10 to 500 Hz, per MIL-STD-202F, Method 204D, Test condition A PROCESS RECOMMENDATIONS TABLE 7.0 Solder Reflow The component solder used internal to this device has a melting point of 221°C. The peak temperature inside the device should be less than or equal to 220°C for a maximum of 10 seconds Wash Ultrasonic cl eaning is not recommended. ORDERING INFORMATION OFC5DJ3BS OCXO SERIES - 10.00MHz CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: Cx067 PAGE 1 OF 2 REV: 04 DATE: 03/09/07 aCopyright 2001 Connor-Winfield all rights reserved. 10.00M THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET PIN CONNECTIONS CRYSTAL CONTROLLED OSCILLATORS Notes: 1) 2) 3) 4) 5) 6) 7) 8) 9) TABLE 8.0 Labels will include the calibr ation frequency at the time of ship. Initial calibration @ 25 °C at the time of shipment. Overall frequency stability ref erenced to measurement at 25 °C. After ten days of continuous operation. Inclusive of calibration, freq uency stability vs. change in tem perature, supply voltage change, load change, hock and vibration, 20 years aging. Vcc = 5.0Vdc. From Vcc=90% of final value. No m ore than 16 transitions at start -up before oscillato r has started. Measured @ 0 °C, within 5 minutes, refer enced one hour after turn -on. For a given off time, the time r equired to meet daily aging, short-term stability. Pin 1 2 6 7 8 9 10 11 12 13 14 15 16 Function N/C Ground N/C Ground Vcc Vcc Ground Ground N/C Ground Output Ground N/C PACKAGE LAYOUT SUGGESTED PAD LAYOUT 12.7 DATE CODE OFC5DJ3BS .310 .310 (7.87mm) 10.00M CW .210 .210 (5.33mm) .110 .110 (2.75mm) .210 .210 (5.33mm) Dimensional Tolerance: ±.005 (.127mm) Pin 1 .110 .110 (2.75mm) KEEP OUT AREAS (3 PLACES) TEST CIRCUIT SOLDER PROFILE Ramp-Up Rate 3°C/second max. from 150°C to 225°C. Temperature 225°C Vcc Vcc GND 7 NC 6 225°C tp Ramp-Down Rate 6°C/second max. 10 GND 11 GND 12 NC 13 GND 14 OUT 15 GND NC 183°C 150°C 100°C GND 2 NC 25°C 0 Time 60-120s Max. 360 Sec. Max. 10-30s 60-150s Max. 50 Ohm Specifications subject to change without notice. DATA SHEET #: Cx067 PAGE 2 OF 2 REV: 04 DATE: 03/09/07 aCopyright 2001 Connor-Winfield all rights reserved.