TA5G-10M

Model TA5G 5.0x7.0mm Surface Mount TCXO 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630-851-5040 www.conwin.com US Headquarters 630-851-4722: European Headquarters: +353-61-472221 Description The Connor Winfield model TA5G is a 5x7mm Surface Mount Temperature Compensated Crystal Controlled Oscillators (TCXO) with a Tri-State LVCMOS output. The TA5G is designed for applications requiring high frequency stability, low jitter over the commercial temperature range. The RoHS compliant, surface mount package is design for high-density mounting and is optimum for mass production. ABSOLUTE M AXIMUM RATING S PARAMETER Storage Temperature Supply Voltage (Vcc) UNITS MINIMUM -55 -0.5 TA5G 0706 10MHz Features TCXO 3.3V Operation LVCMOS Output Logic Frequency Stability: ±2.50ppm Temperature Range: 0 to 70°C Low Jitter 10KHz offset (Vcc) (Icc) 3.135 - INPUT CHARACTERISTICS for ENABLE / DISABLE FUNCTION (Pin 8) PARAMETER Enable Voltage (High) or open circuit Disable Voltage (Low) Output Tri-stated (Vih) (Vil) MINIMUM 70% Vdd NOMINAL MAXIMUM 30% Vdd LVCMOS OUTPUT CHARACTERISTICS PARAMETER LOAD Voltage Current (High) (Low) (High) (Low) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% (Voh) (Vol) (Ioh) (Iol) 90%Vcc -4 45 - Bulletin Page Revision Date Tx182 1 of 2 00 01 Feb 2007 Note: 1) Initial calibration @ 25 °C. Specifications at time of s hipment after 48 hours of operation. 2) Frequency stability vs. change in tem perature. [±(Fmax – Fmin)/2.Fo] 3) Leave Pad 8 unconnected if enable / d isable function is not required. W hen tri-stated, the output stage is disabled but the os cillator and compensation circuit ar e still active (current consumption < 1 mA). Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630-851-5040 www.conwin.com PACKAGE CHARACTERISTICS Package Ceramic Surface Mount Package. TABLE 5 PIN CONNECTIONS TABLE 7 Connection Do not connect Do not connect Do not connect Ground Output Do not connect Do not connect Tri-state Enable / Disable Supply, Vcc Do not connect ENVIRONMENTALS Vibration: Shock: Soldering: Solderability TABLE 6 Vibration per Mil Std 883E Method 2007.3 Test Condition A Mechanical Shock per Mil Std 883E Method 2002.4 Test Condition B. See solder profile page. Solderability per Mil Std 883E Method 2003 PACKAGE DRAWING 0.276 ±0.006 (7.0mm) 0.079 Max. (2.0mm) SUGGESTED PAD LAYOUT 0.295 (7.49mm) 0.030 (0.76mm) TA5G 0706 10MHz Pin 1 0.197 ±0.006 (5.0mm) 0.051 (1.28mm) Pin 1 2 3 4 5 6 7 8 9 10 0.025(6 Places) (0.635mm) 1 0.030 (0.762mm) (4 Places) 2 3 4 10 0.040 (1.02mm) (6 Places) 0.037 (0.94mm) 0.215 (5.46mm) Top View 1 Keep Out Area OUTPUT WAVEFORM 0.100 (2.54mm) 9 0.038 (0.965mm) (4 Places) 8 7 6 5 0.051 (1.28mm) 0.100 (2.54mm) Dimensional Tolerance: ±.005 (.127mm) ±.02 (.508mm) 90% 50% 10% 1 2 3 4 5 8 7 6 15 pF Output TEST CIRCUIT DNC DNC DNC DNC Vcc Supply Voltage .01 uF Bypass 10 9 SOLDER PROFILE Temperature 260°C 220°C 180°C 150°C 120°C 260°C E/D DNC DNC Tape and Reel Information 0 1 120 S Max. Time 10 S 60 S Max. 360 Sec. Max. US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Bulletin TA5G ORDERING INFORMATION TCXO SERIES - 10 MHz CENTER FREQUENCY Tx182 2 of 2 00 01 Feb 2007 Page Revision Date Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation