TL602-024.576M

TCXO Specification Models TL602 and TVL602 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 Description: Features: The Connor-Winfield TL602 and TVL602 are surface mount 5x7mm, 3.3V, LVCMOS Temperature Compensated Crystal Oscillators (TCXO) designed for application compliance to Telcordia Stratum 3, ITU-T G.813 Option 2, and ITU-T G.8262 Option 2. • 3.3 Vdc Operation • Frequency Stability: ± 0.14 ppm • Temperature Range: -40 to 85°C • LVCMOS Output • Ceramic Surface Mount Package • Tape and Reel Packaging • RoHS Compliant / Pb Free Absolute Maximum Ratings www.conwin.com Parameter US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Storage Temperature Supply Voltage (Vcc) Input Voltage Minimum Nominal Maximum Units -55 -0.5 -0.5 - - - 85 6.0 Vcc+0.5 °C Vdc Maximum Units Notes Operating Specifications Parameter Nominal Frequency (Fo) Frequency Calibration @ 25 °C Frequency Stability vs. Temperature Frequency vs. Load Stability Frequency vs. Voltage Stability Static Temperature Hysteresis Short Term Allan Variance (1 second) Constant Temperature Stability Aging 1st Year Total Tolerance Operating Temperature Range: Supply Voltage (Vcc) Supply Current (Icc) Period Jitter Integrated Phase Jitter SSB Phase Noise at 10Hz offset SSB Phase Noise at 100Hz offset SSB Phase Noise at 1KHz offset SSB Phase Noise at 10KHz offset SSB Phase Noise at 100KHz offset Start-up Time Minimum Nominal - -1.0 -140 -50 -50 - - -40 -1.0 -4.6 -40 3.135 - - - - - - - - - 20.0 and 24.576M - - - - - 1.0E-10 - - - - 3.3 - 3 0.5 -80 -110 -135 -150 -150 - - 1.0 140 50 50 0.40 - 40 1.0 4.6 85 3.465 6 5 1.0 - - - - - 1 Notes MHz ppm 1 ppb 2 ppb ±5% ppb ±5% ppm 3 ppb 24 Hours ppm ppm °C Vdc ±5% mA ps rms ps rms 4 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz ms Enable / Disable Input Characteristics (TL602 only) Parameter Minimum Enable Voltage (High) Disable Voltage (Low) Nominal Maximum 70%Vcc - - - 30%Vcc Units Notes Vdc Vdc 5 5 LVCMOS Output Characteristics Parameter Load Voltage (High) (Voh) (Low) (Vol) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Minimum Nominal Maximum - 90%Vcc - 45 - 15 - - 50 4 - - 10%Vcc 55 8 Units Package Characteristics Package Hermetically sealed crystal mounted on a ceramic package Environmental Characteristics Vibration: Shock: Soldering Process; Vibration per Mil Std 883E Method 2007.3 Test Condition A Mechanical Shock per Mil Std 883E Method 2002.4 Test Condition B. RoHS compliant lead free. See soldering profile on page 2. Ordering Information Bulletin Page Revision Date Tx414 1 of 3 02 19 March 2015 Notes pF Vdc Vdc % ns TL602-020.0M, TL602-024.576M, TVL602-020.0M, TVL602-024.576M Notes: 1. Frequency referenced to Fo. @ 25°C. Specification at time of shipment after 48 hours operation 2. Frequency stability vs. change in temperature. [±(Fmax - Fmin)/2.Fo]. 3. Frequency change after reciprocal temperature ramped over the operating range. Frequency measured before and after at 25°C. 4. Bandwidth = 12KHz to Fo/2 MHz. 5. Output is enabled with no connection on pad 8 (for TL602 only). 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com TL602-020.0M Package Layout TL602 Suggested Pad Layout 0.079 Max. (2.0mm) 0.276 ±0.006 (7.0mm) Pad 0.295 (7.49mm) 0.051 (1.28mm) 0.030 (0.76mm) Keep Out Area 0.197 ±0.006 (5.0mm) TL602 1438 20.0 MHZ 8 0.037 (0.94mm) 0.215 (5.46mm) 0.025(6 Places) (0.635mm) Pin 1 10 0.030 (0.762mm) (4 Places) 2 1 Temperature 3 220°C 120°C 0 10 s Up to 120 s 60 to 90 s Typical Typical Meets IPC/JEDEC J-STD-020C 0.100 (2.54mm) Bottom View 9 8 0.038 (0.965mm) (4 Places) 7 0.040 (1.02mm) (6 Places) 5 6 6 5 Top View 10 4 2 3 0.051 (1.28mm) * Do not route any traces in the keep out area. It is recommended the next layer under the keep out area is to be ground plane. Dimensional Tolerance: ±.005 (.127mm) ±.02 (.508mm) 0.100 (2.54mm) 7 9 1 4 260°C 260°C 180°C 150°C TL602 Pad Connections Connection 1: Do Not Connect 2: Do Not Connect 3: Do Not Connect 4: Ground 5: Output 6: Do Not Connect 7: Do Not Connect 8: Tri-State Enable / Disable 9: Supply Voltage Vcc 10: N/C Output Waveform Solder Profile Temperature TL602-024.576M Package Layout 260°C 260°C 220°C TL602 1438 150°C 0.095 (2.4mm) (2.4mm) (7.0mm) TL602 1438 24.576MHz MHz 24.576 180°C 0.095 0.276 ±0.006 ±0.006 (7.0mm) 0.276 120°C 0.197 0 0.197 ±0.006 ±0.006 (5.0mm) (5.0mm) 10 s Up to 120 s 60 to 90 s Typical Typical 1V/Div Meets IPC/JEDEC J-STD-020C TVL602-020.0M Package Layout 0.276 ±0.006 (7.0mm) (Top View) TVL602 Suggested Pad Layout 0.079 Max. (2.0mm) 0.071 (1.8mm) 4 Places 4 TVL602 1511 20.0 MHZ 0.197 ±0.006 (5.0mm) 0.165 (4.2mm) 0.034 (0.90mm) (4 Places) 2 (Bottom View) 4 3 Dimensional Tolerance: ±.005 (.127mm) ±.02 (.508mm) 0.055 (1.40mm) (4 Places) 0.047 (1.2mm) 4 Places (Top View) Pad 1 1 3 1 0.224 (5.7mm) 2 TVL602 Pad Connections Pad 1: 2: 3: 4: Connection N/C Ground Output Supply Voltage Vcc Keep Out * Area * Do not route any traces in the keep out area. It is recommended the next layer under the keep out area is to be ground plane. TVL602-024.576M Package Layout 0.095 0.095 (2.4mm) (2.4mm) 0.276 ±0.006 (7.0mm) TL602 1438 TVL602 1511 24.576 MHz 24.576 MHz 0.197 0.197 ±0.006 ±0.006 (5.0mm) (5.0mm) Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Tx414 2 of 3 02 19 March 2015 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Design Recommendations Vcc, should have a large copper area for reduced inductance. Connect a 0.01uF bypass capacitor