LP301105

MAGNUM ® Series A5000 & Series CB5000 Single Row Terminal Blocks SPECIFICATIONS Rating: 10A, 300V* Center Spacing: .250” (6.35 mm) Wire Range: #16-30 AWG CU Screw Size: #3-48 zinc plated philslot SEMS screws, wireready standard Torque Rating: 4 in-lbs. Distance Between Barriers: .20” (5.08 mm) Recommended PCB Hole Diameter: .062” (1.57 mm) Operating Temperature: 105°C (221°F) max., -40°C (-40°F) min. Molded Material: Black, UL Rated 94V0 Thermoplastic Breakdown Voltage: 1600V rms Agency Information: UL/CSA; CE Certified * Max. rating shown; some options may be rated lower – consult factory. A50110507 Single & Double Row Filtered Connectors CB50220807 Euro-MAG Series PCB – Spring Clamp A5000 Series MOUNTING ENDS A B Mount Overall Centers Length .75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 1.06 1.31 1.56 1.81 2.06 2.31 2.56 2.81 3.06 3.31 3.56 3.81 4.06 4.31 4.56 4.81 5.06 5.31 5.56 5.81 6.06 6.31 6.56 6.81 7.06 7.31 7.56 BARRIER ENDS A B Pole Overall Centers Length .25 .50 .75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 .56 .81 1.06 1.31 1.56 1.81 2.06 2.31 2.56 2.81 3.06 3.31 3.56 3.81 4.06 4.31 4.56 4.81 5.06 5.31 5.56 5.81 6.06 6.31 6.56 6.81 7.06 7.31 7.56 .12 (3.0) dia. #3-48 screw .250 (6.35) .43 (10.9) B Poles 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Base & Rail Mount Connectors Mount End Barrier End .50 (12.7) .025 (.64) Barrier End .25 (6.35) Mount End A CB5000 Series #3-48 screw .12 (3.0) dia. .250 (6.35) .50 (12.7) Power Distribution Blocks * Dimensions in inches. To convert to millimeters, multiply by 25.4. B Mount End Barrier End .50 (12.7) WIRE MANAGEMENT PRODUCTS .025 (.64) Mount End A Barrier End 1 MAGNUM ® Part Numbering System Single & Double Row Filtered Connectors Series Terminal Style Base/End Poles Screw Options Options A5 CB5 A5 - standard barrier CB5 - closed barrier 01 02 03 04 - handwired - printed circuit - non feed-thru - wire wrap tail 1 - mount end 2 - barrier end 02 to 30 02 to 28 on mount end base 07 - steel SEMS std. wire ready C1 to C8 - .110” QC L1 to L6 marking options (pg 22) LT1 to LT6 marking options (CB5 only-pg 22) OJ - over barrier jumper S1 - single solder lug/flat S2 - double solder lug/flat (A5 only) Inches (Millimeters) Euro-MAG Series PCB – Spring Clamp Terminal Styles .40 (10.2) .10 (2.54) .025 (.64) .12 (3.0) .045 (1.14) .17 (4.3) .025 (.64) .045 (1.14) .50 (12.7) .025 (.64) .12 (3.0) .12 (3.0) 01 Handwired 02 Circuit Board 03 Non Feed-Thru 04 Wire Wrap Tail CB5 Terminal Exit Options Base & Rail Mount Connectors Inches (Millimeters) .12 (3.0) Exit Rear (std.) Screw Options Wire ready screws standard on all terminal styles Power Distribution Blocks 07 Steel SEMS Zinc Plated 07 Standard Wire Ready Hardware Options Jumpers (Bulk ordering part numbers are in parentheses.) Solder Lugs Quick Connects Blade Width .110” (For other orientations, contact factory.) .56 (14.3) WIRE MANAGEMENT PRODUCTS OJ12 C1 (5C1) * C2 (5C2) * C4 (5C4) * S1 (5S1) 1.12 (28.4) C7 (5C7) * N/A on CB5 Series. C8 (5C8) S2 (5S2) 2 Series A1000 & Series CB1000 Single Row Terminal Blocks Single & Double Row Filtered Connectors SPECIFICATIONS Rating: 20A, 150V Center Spacing: .325” (8.26 mm) Wire Range: #14-22 AWG CU Screw Size: #6-32 zinc plated philslot wire-ready screws with a #2 driving recess. Torque Rating: 9 in-lb. Base: Standoffs are standard on CB1000 Series for easy flux washing. Distance Between Barriers: .26” (6.6 mm) Recommended PCB Hole Diameter: .070” (1.78 mm) Operating Temperature: 105°C (221°F) max., -40°C (-40°F) min. Molded Material: Black, UL Rated 94V0 Thermoplastic Breakdown Voltage: 1600V Agency Information: UL/CSA; IEC Compliance; CE Certified CB10210707 A102206 Euro-MAG Series PCB – Spring Clamp A1000 Series .325 (8.26) .15 (3.8) dia. Poles 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 MOUNTING ENDS ONLY A C Mount Ctrs. Length .98 1.30 1.63 1.95 2.28 2.60 2.93 3.25 3.58 3.90 4.23 4.55 4.88 5.20 5.53 5.85 6.18 6.50 6.83 7.15 7.48 7.80 8.13 8.45 8.78 9.10 9.43 9.75 10.08 10.40 10.73 11.05 11.38 1.37 1.69 2.02 2.34 2.67 2.99 3.32 3.64 3.97 4.29 4.62 4.94 5.27 5.59 5.92 6.24 6.57 6.89 7.22 7.54 7.87 8.19 8.52 8.84 9.17 9.49 9.82 10.14 10.47 10.79 11.12 11.44 11.77 BARRIER & MOUNTING ENDS B Pole Ctrs. .33 .65 .98 1.30 1.63 1.95 2.28 2.60 2.93 3.25 3.58 3.90 4.23 4.55 4.88 5.20 5.53 5.85 6.18 6.50 6.83 7.15 7.48 7.80 8.13 8.45 8.78 9.10 9.43 9.75 10.08 10.40 10.73 11.05 11.38 BARRIER ENDS ONLY C Length .72 1.04 1.37 1.69 2.02 2.34 2.67 2.99 3.32 3.64 3.97 4.29 4.62 4.94 5.27 5.59 5.92 6.24 6.57 6.89 7.22 7.54 7.87 8.19 8.52 8.84 9.17 9.49 9.82 10.14 10.47 10.79 11.12 11.44 11.77 .50 (12.7) C Mount End Barrier End Base & Rail Mount Connectors .25 (6.4) .50 (12.7) A Mount Centers B Pole Centers Mount End Barrier End CB1000 Series .15 (3.8) dia. .325 (8.26) .60 (15.2) Power Distribution Blocks .25 (6.4) C Mount End Barrier End .27 (6.9) .52 (13.2) WIRE MANAGEMENT PRODUCTS A Mount Centers B Pole Centers Mount End Barrier End .025 (.64) * Dimensions in inches. To convert to millimeters, multiply by 25.4. 3 MAGNUM ® Part Numbering System Series Single & Double Row Filtered Connectors Terminal Style Base/End Poles Screw Options Options A1 CB1 A1 - standard barrier CB1 - closed barrier 02 03 04 07 - printed circuit - non feed-thru - wire wrap tail - extended pin 1 - mount end 2 - barrier end 02 to 36 02 to 34 on mount end base Blank - std. screws AB & DR - angle mts. (A1 only-pg 5) 03 - stainless steel B1 to B9 - .187” QC (all positions) 04 - nickel brass EB - exit back terminals on CB1 w/07 screw 07 - steel SEMS & option only washer (not JA, JB & JC - barrier jumpers available with L1 to L6 marking options (pg 22) hardware options) LT1 to LT6 marking options (CB1 only-pg 22) CA - standard captive screw MP & MT - mounting plates (pg 5) 07CA - SEMS captive R26 & R45 - right angle bends (A1 only-pg 5) Inches (Millimeters) Covers - (pg 23) Terminal Styles Euro-MAG Series PCB – Spring Clamp .16 (4.1) .055 (1.40) .032 (.81) .055 (1.40) .35 (8.9) .14 (3.6) .032 (.81) .14 (3.6) .055 (1.40) .54 (13.7) .0 (.8 .14 (3.6) 02 Printed Circuit 03 Non Feed-Thru 04 Wire Wrap Tail 07 Extended Pin Screw Options Wire ready screws standard on all terminal styles Base & Rail Mount Connectors Standard Zinc Plated Steel 03 Stainless Steel 04 Brass Nickel Plated 07 Steel SEMS Zinc Plated CB1 Terminal Exit Options .275 (6.98) .14 (3.6) Inches (Millimeters) Exit Rear (std.) Power Distribution Blocks EB Exit Back (Bulk ordering part numbers are in parentheses.) Hardware Options Jumpers .33 (8.4) Quick Connects Blade Width B = .187”. (For other orientations, contact factory.) JA (JA1-XX) .33 (8.4) B1 (1B1) * B2 (1B2) * B3 (1B3) * B4 (1B4) * WIRE MANAGEMENT PRODUCTS JB (JB1-XX) .33 (8.4) B5 (1B5) * B6 (1B6) * B7 (1B7) B8 (1B8) * N/A on CB1 Series. JC (JC1-XX) B9 (1B9) 4 Series A1000 & CB1000 Single Row Terminal Blocks Single & Double Row Filtered Connectors Mounting Options Right Angle Bends (A1 only) Right angle terminals are offered on the A1000 Series. Configurations are defined in these dimensions: X = pin extension beyond the block base; Z = length from block base to centerline of the terminal tip. Standard bends consist of the X and Z dimensions shown in the chart. Specify by adding the selected Bend Option Code to the terminal part no. Inches (Millimeters) Bend Option Code R26 (04 terminal only) R45 (07 terminal only) Dimensions in inches. To convert to millimeters, multiply by 25.4. Angle Brackets (A1 only) .250 .04 .150 Option AB Angle brackets enable block to be fastened at right angles to normal mount position. Bulk part no. 1AB. Mounting Plates MOUNTING PLATE Options MP & MT MP Metal inserts with .150” dia. hole accept #6 screw. MT Metal inserts with tapped hole accept #6-32 screw. Bulk Part Nos. 1MP & 1MT. ; ;; ; ; X Z Euro-MAG Series PCB – Spring Clamp X (minimum) .14 .33 Z .09 .09 Base & Rail Mount Connectors Drilled Right Angle (A1 only) .325 .12 .450 .320 .144 HOLE w/.312 C' BORE Option DR Counterbored holes across mount ends of block enable fastening with two screws at right angles to normal mount position. Power Distribution Blocks MP MT WIRE MANAGEMENT PRODUCTS 5 MAGNUM ® Series A2000, LP2000 & CB2000 Single Row Terminal Blocks Single & Double Row Filtered Connectors A20510807WR Euro-MAG Series PCB – Spring Clamp SPECIFICATIONS Rating: A2: 30A, 300V* LP2: 30A, 150V* CB2: 30A, 300V* Center Spacing: .375” or 3/8” (9.52 mm) LP202110 Wire Range: #12-22 AWG CU Screw Size: #6-32 zinc plated philslot Torque Rating: 9 in-lb. Base: Standoffs standard for easy flux washing Distance Between Barriers: .32” (8.1 mm) Recommended PCB Hole Diameter: .076” (1.93 mm) Operating Temperature: 105°C (221°F) max., -40°C (-40°F) min. Molded Material: Black, UL Rated 94V0 Thermoplastic Breakdown Voltage: 3400V (A2 & LP2); 4100V (CB2). Agency Information: UL/CSA; IEC Compliance; CE Certified *30A Rating achieved with a #10 copper wire crimped to a ring terminal.; 20A Rating without ring terminal. CB20210507 A2000 & LP2000 Series .375 (9.53) .15 (3.8) dia. .65 (16.5) Poles 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 MOUNTING ENDS ONLY A C Mount Ctrs. Length 1.13 1.50 1.88 2.25 2.63 3.00 3.38 3.75 4.13 4.50 4.88 5.25 5.63 6.00 6.38 6.75 7.13 7.50 7.88 8.25 8.63 9.00 9.38 9.75 10.13 10.50 10.88 11.25 11.63 1.56 1.93 2.30 2.68 3.06 3.43 3.81 4.18 4.56 4.93 5.31 5.69 6.06 6.43 6.81 7.18 7.56 7.93 8.31 8.68 9.06 9.43 9.81 10.18 10.56 10.93 11.31 11.68 12.05 BARRIER & MOUNTING ENDS B Pole Ctrs. .38 .75 1.13 1.50 1.88 2.25 2.63 3.00 3.38 3.75 4.13 4.50 4.88 5.25 5.63 6.00 6.38 6.75 7.13 7.50 7.88 8.25 8.63 9.00 9.38 9.75 10.13 10.50 10.88 11.25 11.63 BARRIER ENDS ONLY C Length .81 1.18 1.56 1.93 2.31 2.68 3.06 3.43 3.81 4.18 4.56 4.93 5.31 5.68 6.06 6.43 6.81 7.18 7.56 7.93 8.31 8.68 9.06 9.43 9.81 10.18 10.55 10.93 11.31 11.68 12.05 C Mount End Barrier End Base & Rail Mount Connectors .76 (19.3) .40 (10.2) .565 (14.35) on LP2000 A Mount Centers B Pole Centers Mount End Barrier End .02 (.5) CB2000 Series .19 (4.8) dia. Power Distribution Blocks .375 (9.53) .70 (17.8) .32 (8.1) Mount End C Barrier End .60 (15.2) WIRE MANAGEMENT PRODUCTS * Dimensions in inches. To convert to millimeters, multiply by 25.4. A Mount Centers B Pole Centers Mount End Barrier End .02 (.5) 6 Series A2000 & LP2000 Single Row Terminal Blocks Single & Double Row Filtered Connectors Part Numbering System Series Terminal Style Base/End Poles Screw Options Options A2 LP2 A2 - standard barrier 01 - handwired LP2 - low profile 02 - printed circuit barrier 03 - non feed-thru 04 - wire wrap tail 05 - extended handwired 06 - handwired 07 - extended pin 08 - printed circuit 09 - .250 QC short 10 - .187 QC 14 - printed circuit 19 - .250 QC long 0 - flat base/molded 02 to 32 mount end 02 to 30 on mount 1 - flat base/mnt. end end base 2 - flat base/barrier end 3 - insulator base/mnt. end 4 - insulator base/ barrier end 5 - closed base/ mount end 6 - closed base/ molded mount end 9 - insulator base/ molded mount end Base/End Note: 0, 6, 9 styles not available with covers. 5 & 6 Styles only available with 03 terminals. Blank - std. screw AB - angle mnt. options (pg 9) 00 - screws shipped bulk A1 to A9 - .250” QC 03 - stainless steel B1 to B9 - .187” QC 04 - brass nickel plated DR - drilled right angle (pg 9) 07 - steel SEMS JA, JB & JC - barrier jumpers (not available L1 to L6 marking options (pg 22) with hardware options) MP, MP8 & MT mounting plates (pg 9) 09 - brass SEMS OJ2 & OJ4 - over barrier jumpers (not nickel plated available w/covers) (not available with RC - retaining clips (pg 9) hardware options) R30 to R77 - right angle bends (pg 9) CA - captive screw SO - stand off insulators (pg 9) 03CA - stainless steel captive S1 - solder lug/flat 04CA - brass captive 07CA - SEMS captive Covers - (pg 23) 09CA - brass SEMS captive 07WR - steel SEMS wire ready (not available on LP2) Euro-MAG Series PCB – Spring Clamp Base & Rail Mount Connectors Terminal Styles Inches (Millimeters) .55 (14.0) 031 .79) .110 (2.79) .20 (5.1) .031 (.79) .062 (1.57) .55 (14.0) .031 (.79) .062 (1.57) 01 Handwired 02 Printed Circuit 03 Non Feed-Thru 04 Wire Wrap Tail Power Distribution Blocks .66 (16.8) .031 (.79) .30 (7.6) .11 (2.79) .82 (20.8) .031 (.79) .031 (.79) .062 (1.57 ) .17 (4.3) .062 (1.57) .031 (.79) .110 (2.79) 05 Extended Handwired 06 Handwired 07 Extended Pin 08 Printed Circuit WIRE MANAGEMENT PRODUCTS .33 (8.4) .40 (10.2) .031 (.79) .250 (6.35) .031 (.79) .42 (10.7) .031 (.79) .125 (3.2) .062 (1.57) .031 (.79) .72 (18.3) .31 (7.9) .187 (4.75) .41 (10.4) .250 (6.35) 09 .250 QC short 10 .187 QC 14 Printed Circuit 19 .250 QC long 7 MAGNUM ® Series A2000 & LP2000 Single Row Terminal Blocks Continued Single & Double Row Filtered Connectors Screw Options Standard Zinc Plated Steel 03 Stainless Steel 04 Brass Nickel Plated 07 Steel SEMS 09 Brass SEMS Nickel Plated 07WR Wire Ready (A2 only) Euro-MAG Series PCB – Spring Clamp Hardware Options Solder Lugs .68 (17.3) .33 (8.4) (Bulk ordering part numbers are in parentheses.) Quick Connects Blade Width A = .250” Blade Width B = .187” Inches (Millimeters) Jumpers .84 (21.2) S1 (2S1) JA (JA2-XX) .33 (8.4) OJ2 A1 & B1 (2A1 & 2B1) A2 & B2 (2A2 & 2B2) A3 & B3 (2A3 & 2B3) Base & Rail Mount Connectors JB (JB2-XX) .33 (8.4) OJ4 A4 & B4 (2A4 & 2B4) A5 & B5 (2A5 & 2B5) A6 & B6 (2A6 & 2B6) JC (JC2-XX) A7 & B7 (2A7 & 2B7) A8 & B8 (2A8 & 2B8) A9 & B9 (2A9 & 2B9) Base/End Options Power Distribution Blocks B B B B .180 (4.57) .150 dia. (3.8) mounting holes (2) .218 (5.54) .40 (10.2) WIRE MANAGEMENT PRODUCTS .40 10.2) SECTION A–A .095 (2.4) SECTION B–B 0, 6 & 9 Molded Mount End 1, 3 & 5 Mount End 8 Series A2000 & LP2000 Single Row Terminal Blocks Continued Single & Double Row Filtered Connectors Mounting Options Right Angle Bends (A2, LP2 only) Right angle terminals are offered on the A2000 & LP2000 Series. Configurations are defined in these dimensions: X = pin extension beyond the block base; Z = length from block base to centerline of the terminal tip. Standard bends consist of the X and Z dimensions shown in the chart. Specify by adding the selected Bend Option Code to the terminal part no. 07 Terminal Bend Configurations 04 Terminal Bend Configurations .82 Z X Euro-MAG Series PCB – Spring Clamp Z Bend Option Code R30 R35 R36 R39 R42 R46 R48 R50 Angle Brackets (A2, LP2 only) .15 Option AB Angle brackets enable block to be fastened at right angles to normal mount position. Bulk part no. 2AB. Mounting Plates MOUNTING PLATE Options MP, MP8 & MT MP Metal inserts with .150” dia. hole accept #6 screw. MP8 Metal inserts with .187” dia. hole accept #8-32 screw. MT Metal inserts with tapped hole accept #6-32 screw. ; ;; ; ; ;; X (minimum) -.04 .01 .02 .05 .08 .12 .14 .16 Z Available w/insulator base No No No No No No No No .28 .23 .22 .19 .16 .12 .10 .08 R30 R35 R36 R42 R46 R50 R53 R66 R69 R75 R77 -.04 .01 .02 .08 .12 .16 .19 .32 .35 .41 .43 .55 .50 .49 .43 .39 .35 .32 .19 .16 .10 .08 Yes Yes Yes Yes Yes No No No No No No Dimensions in inches. To convert to millimeters, multiply by 25.4. .55 X Bend Option Code X (minimum) Z Available w/insulator base Base & Rail Mount Connectors Drilled Right Angle (A2, LP2 only) .375 .24 .25 .04 .45 .32 .144 HOLE w/.312 C' BORE Power Distribution Blocks Option DR Counterbored holes across mount ends of block enable fastening with two screws at right angles to normal mount position. Standoffs Retaining Clip MP MP8 WIRE MANAGEMENT PRODUCTS .300 MT RETAINING CLIP STANDOFF Option SO Standoff mounts are tubes molded to the mounting positions. Available with insulator bases only. Option RC Use on standoff tubes. Fit panels up to .125” thick. Two clips for every five positions. Supplied unassembled. Bulk Part No. H541. 9 MAGNUM ® Series CB2000 Single Row Terminal Blocks Single & Double Row Filtered Connectors Part Numbering System Series Terminal Style Base/End Poles Screws Options CB2 CB2 - closed back 01 02 03 07 14 22 - handwired - printed circuit - non feed-thru - extended pin - printed circuit - dual tail printed circuit 1 - mount end 2 - barrier end 02 to 32 02 to 30 on mount end base 03 - stainless steel 04 - brass nickel plated 07 - steel SEMS standard 09 - brass SEMS nickel plated CA - captive screw 07CA - SEMS captive AB - angle mounting brackets (pg 11) A7 to A9 - .250” QC B7 to B9 - .187” QC EB - exit back terminals EF - exit front terminals JA, JB & JC - barrier jumpers L1 to L6 marking options (pg 22) LT1 to LT6 marking options (pg 22) OJ2 & OJ4 - over barrier jumpers MP, MP8, MT & MT8 mtg. plates (pg 11) S1 - solder lug/flat Covers - (pg.23) Euro-MAG Series PCB – Spring Clamp Terminal Styles Inches (Millimeters) .19 (4.9) .81 (4.6) Base & Rail Mount Connectors .40 (10.2) .120 (3.05) .0 (.7 .18 (4.6) .045 (1.14) .19 (4.8 ) .18 (4.6) .0 (. .062 (1.57) .70 (17.8) .0 (. .125 (3.18) .045 (1.14) .18 (4.6) .0 (.7 .045 (1.14) .03 (.79) .40 (10.2) .43 (10.9) .18 (4.6) 01 Handwired 02 Printed Circuit 03 Non Feed-Thru Available on Mount End (1) only. 07 Extended Pin 14 Printed Circuit 22 Dual Tail Printred Circuit Screw Options Power Distribution Blocks 03 Stainless Steel 04 Brass Nickel Plated 07 Steel SEMS Zinc Plated 09 Brass SEMS Nickel Plated * NOTE: Wire ready screws standard on all terminal styles. CB2 Terminal Exit Options Y Inches (Millimeters) WIRE MANAGEMENT PRODUCTS .255 (6.48) .18 (4.6) X .18 (4.6) X Exit Rear (std.) EF Exit Front EB Exit Back 10 Series CB2000 Single Row Terminal Blocks Single & Double Row Filtered Connectors Hardware Options Solder Lugs .68 (17.3) (Bulk ordering part numbers are in parentheses.) Inches (Millimeters) Jumpers Quick Connects Blade Width A = .250”. Blade Width B = .187”. .33 (8.4) .84 (21.2) S1 (2S1) JA (JA2-XX) .33 (8.4) OJ2 A7 & B7 (2A7 & 2B7) A8 & B8 (2A8 & 2B8) A9 & B9 (2A9 & 2B9) Euro-MAG Series PCB – Spring Clamp JB (JB2-XX) .33 (8.4) OJ4 JC (JC2-XX) Mounting Options Right Angle Mounting Bracket End Positions usable Snap-in Angle Bracket A Exit Back (EB) Terminals Angle Bracket .24 (6.1) .42 (10.7) A Mounts blocks on PC boards at a right angle. • Protects solder joints. • Recommended for all EB (Exit Back) PCB terminal blocks. • Bracket snaps securely on block (no hardware required). • Minimum strip length (end positions are usable). • Mount with #6-32 or #8-32 screws (not supplied). Mounting Plates MOUNTING PLATE ; MP MP8 MT MT8 ; ; .71 (18.0) .79 (20.1) 1.02 (25.8) Base & Rail Mount Connectors Inches (Millimeters) Chassis or PCB #6 or #8 mounting screw & nut (Customer supplied.) .45 (11.4) Power Distribution Blocks Option AB WIRE MANAGEMENT PRODUCTS Options MP, MP8, MT & MT8 MP Metal inserts with .150” dia. hole accept #6 screw. MP8 Metal inserts with .187” dia. hole accept #8-32 screw. MT Metal inserts with tapped hole accept #6-32 screw. MT8 Metal inserts with tapped hole accept #8-32 screw. 11 MAGNUM ® A31940707WR Series A3000, LP3000 & CB3000 Single Row Terminal Blocks Single & Double Row Filtered Connectors Euro-MAG Series PCB – Spring Clamp SPECIFICATIONS Rating: A3: 30A, 600V* #12-22 AWG LP3: 30A, 150V #12-22 AWG CB3: 30A, 600V #12-22 AWG Wire Range: #12-22 AWG CU Center Spacing: .437” or 7/16” (11.10 mm) Screw Size: #6-32 zinc plated philslot screws. Torque Rating: 9 in-lb. Base: Standoffs standard for easy flux washing. Distance Between Barriers: .32” (8.1 mm) Recommended PCB Hole Diameter: .076” (1.93 mm) Operating Temperature: 105°C (221°F) max., -40°C (-40°F) min. Molded Material: Black, UL Rated 94V0 Thermoplastic Breakdown Voltage: 3500V (A3 & LP3); 8200V (CB3) Agency Information: UL/CSA; IEC Compliance, CE Certified *30A Rating achieved with a #10 copper wire crimped to a ring terminal; 20 Rating without ring terminal. LP301105 CB31420807 A3000 & LP3000 Series .437 (11.10) .15 (3.8) dia. .65 (16.5) Base & Rail Mount Connectors Poles 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 MOUNTING ENDS ONLY A C Mount Ctrs. Length 1.31 1.75 2.18 2.62 3.06 3.50 3.93 4.37 4.81 5.25 5.68 6.12 6.56 7.00 7.43 7.87 8.31 8.75 9.18 9.62 10.06 10.50 10.93 11.37 11.81 1.73 2.17 2.61 3.05 3.48 3.92 4.36 4.80 5.23 5.67 6.11 6.55 6.98 7.42 7.86 8.30 8.73 9.17 9.60 10.05 10.48 10.92 11.36 11.80 12.23 BARRIER & MOUNTING ENDS B Pole Ctrs. .43 .87 1.31 1.75 2.18 2.62 3.06 3.50 3.93 4.37 4.81 5.25 5.68 6.12 6.56 7.00 7.43 7.87 8.31 8.50 9.18 9.62 10.06 10.50 10.93 11.37 11.81 BARRIER ENDS ONLY C Length .98 1.43 1.87 2.31 2.75 3.18 3.62 4.06 4.50 4.93 5.37 5.81 6.25 6.68 7.12 7.56 8.00 8.43 8.87 9.31 9.75 10.18 10.62 11.06 11.50 11.93 12.37 .40 (10.2) C Mount End Barrier End .565 (19.3) .76 (14.35) A Mount Centers B Pole Centers Mount End Barrier End .02 (.5) CB3000 Series .437 (11.10) .19 (4.8) dia. .32 (8.1) C Mount End Barrier End Power Distribution Blocks .70 (17.8) .61 (15.5) WIRE MANAGEMENT PRODUCTS Dimensions in inches. To convert to millimeters, multiply by 25.4. A Mount Centers B Pole Centers Mount End Barrier End .02 (.5) 12 Series A3000 & LP3000 Single Row Terminal Blocks Single & Double Row Filtered Connectors Part Numbering System Series Terminal Style Base/End (Views pg. 15) Poles Screw Options Options A3 LP3 A3 - standard barrier LP3 - low profile barrier 01 - handwired 02 - printed circuit 03 - non feed-thru 04 - wire wrap tail 05 - extended handwired 06 - handwired 07 - extended pin 08 - printed circuit 09 - .250 QC short 10 - .187 QC 14 - printed circuit 19 - .250 QC long 1 - flat base/mnt. end 02 to 28 2 - flat base/barrier end 02 to 26 on mount 3 - insulator base/ end base mnt. end 4 - insulator base/ barrier end 5 - closed base/ mount end Blank - std. screw 00 - screws shipped bulk 03 - stainless steel 04 - brass nickel plated 07 - steel SEMS zinc plated (not available with hardware options) 09 - brass SEMS nickel plated (not available with hardware options) 03CA - stainless steel captive 04CA - brass captive 07CA - SEMS captive 09CA - brass SEMS captive 07WR - steel SEMS wire ready (A3 only) AB - angle mnt. options (pg 15) A1 to A9 - .250” QC B1 to B9 - .187” QC DR - drilled right angle (pg 15) J201 - flat slip-on jumper L1 to L6 marking options (pg 22) MP, MP8 & MT mounting plates (pg 15) OJ3, OJ5 & OJ7 - over barrier jumpers RC - retaining clips (pg 15) R30 to R77 - right angle bends (pg 15) SO - stand off insulators (pg 15) S1 - solder lug/flat Covers - (pg 23) Euro-MAG Series PCB – Spring Clamp Base/End Note: 5 Style only available with 03 terminals. Terminal Styles Inches (Millimeters) Base & Rail Mount Connectors .55 (14.0) .20 (5.1) .031 (.79) .06 (1.5 .031 (.79) .55 (14.0) .06 (1.5 .66 (16.8) .031 (.79) .031 (.79) .11 (2.7 .30 (7.6) .1 (2.7 .031 (.79) .1 (2 01 Handwired 02 Printed Circuit 03 Non Feed-Thru 04 Wire Wrap Tail 05 Extended Handwired 06 Handwired Power Distribution Blocks .33 (8.4) .82 (20.8) .17 (4.3) .031 (.79) .06 (1.5 .062 (1.57) .40 (10.2) .031 (.79) .2 (6. .031 (.79) .42 (10.7) .72 (18.3) .031 (.79) .1 (4. .125 (3.2) .062 (1.57 .31 (7.9) .031 (.79) .41 (10.4) .031 (.79) .250 (6.35) 07 Extended Pin 08 Printed Circuit 09 .250 QC Short 10 .187 QC 14 Printed Circuit 19 .250 QC Long Screw Options WIRE MANAGEMENT PRODUCTS Standard Zinc Plated Steel 03 Stainless Steel 04 Brass Nickel Plated 07 Steel SEMS Zinc Plated 09 Brass SEMS Nickel Plated 07WR Wire Ready (A3 only) 13 MAGNUM ® Series A3000 & LP3000 Single Row Terminal Blocks Continued Single & Double Row Filtered Connectors Hardware Options Solder Lugs (Bulk ordering part numbers are in parentheses.) Jumpers Inches (Millimeters) Quick Connects Blade Width A = .250” Blade Width B = .187” .68 (17.3) .84 (21.2) S1 (2S1) OJ3 J201 Flat slip-on A1 & B1 (2A1 & 2B1) A2 & B2 (2A2 & 2B2) A3 & B3 (2A3 & 2B3) Euro-MAG Series PCB – Spring Clamp OJ7 LP3 Only A4 & B4 (2A4 & 2B4) A5 & B5 (2A5 & 2B5) A6 & B6 (2A6 & 2B6) OJ5 A7 & B7 (2A7 & 2B7) A8 & B8 (2A8 & 2B8) A9 & B9 (2A9 & 2B9) Base/End Options Base & Rail Mount Connectors B B .150 dia. (3.8) mounting holes (2) .40 (10.2) .095 (2.4) SECTION B–B Power Distribution Blocks 1, 3 & 5 Mount End WIRE MANAGEMENT PRODUCTS 14 Series A3000 & LP3000 Single Row Terminal Blocks Mounting Options Right Angle Bends (A3, LP3 only) Continued Single & Double Row Filtered Connectors Right angle terminals are offered on the A3000 & LP3000 Series. Configurations are defined in these dimensions: X = pin extension beyond the block base; Z = length from block base to centerline of the terminal tip. Standard bends consist of the X and Z dimensions shown in the chart. Specify by adding the selected Bend Option Code to the terminal part no. 07 Terminal Bend Configurations 04 Terminal Bend Configurations Euro-MAG Series PCB – Spring Clamp Z .82 .55 X Z X Bend Option Code R30 R35 R36 R39 R42 R46 R48 R50 X (minimum) -.04 .01 .02 .05 .08 .12 .14 .16 Angle Brackets (A3, LP3 only) .25 .04 .15 Option AB Angle brackets enable block to be fastened at right angles to normal mount position. Bulk part no. 2AB. Mounting Plates MOUNTING PLATE Options MP, MP8 & MT MP Metal inserts with .150” dia. hole accept #6 screw. MP8 Metal inserts with .187” dia. hole accept #8-32 screw. MT Metal inserts with tapped hole accept #6-32 screw. ; ;; ; ; ;; Z Available w/insulator base No No No No No No No No Bend Option Code R30 R35 R36 R50 R53 R66 R69 R75 R77 X (minimum) -.04 .01 .02 .16 .19 .32 .35 .41 .43 Z Available w/insulator base Yes Yes Yes No No No No No No .28 .23 .22 .19 .16 .12 .10 .08 .55 .50 .49 .35 .32 .19 .16 .10 .08 Dimensions in inches. To convert to millimeters, multiply by 25.4. Base & Rail Mount Connectors Drilled Right Angle (A3, LP3 only) .437 .24 .45 Power Distribution Blocks .32 .144 HOLE w/.312 C' BORE Option DR Counterbored holes across mount ends of block enable fastening with two screws at right angles to normal mount position. Standoffs Retaining Clip MP MP8 WIRE MANAGEMENT PRODUCTS .300 MT RETAINING CLIP STANDOFF Option SO Standoff mounts are tubes molded to the mounting positions. Available with insulator bases only. Option RC Use on standoff tubes. Fit panels up to .125” thick. Two clips for every five positions. Supplied unassembled. Bulk Part No. H541. 15 MAGNUM ® Series CB3000 Single Row Terminal Blocks Single & Double Row Filtered Connectors Part Numbering System Series Terminal Style Base/End Poles Screws Options CB3 CB3 - closed back 01 - handwired #6-32 screw 02 - printed circuit #6-32 screw 03 - non feed-thru #6-32 screw 07 - extended pin #6-32 screw 14 - printed circuit #6-32 screw 51 - handwired #8-32* 52 - printed circuit #8-32* 53 - non feed-thru #8-32* 57 - extended pin #8-32* 64 - printed circuit #8-32* *Note: #8-32 screw is a special with #6-32 head. 1 - mount end 2 - barrier end 5 - closed base/ mount end 02 to 28 02 to 26 on mount end base 07 - steel SEMS 09 - brass SEMS nickel plated 07CA - SEMS captive AB - angle mounting brackets (pg 17) A7 to A9 - .250” QC B7 to B9 - .187” QC EB - exit back terminals L1 to L6 marking options (pg 22) LT1 to LT6 marking options (pg 22) OJ3 & OJ7 - over barrier jumpers MP, MP8, MT & MT8 mtg. plates (pg 17) S1 - solder lug/flat Covers - (pg 23) Euro-MAG Series PCB – Spring Clamp Base/End Note: 5 Style only available with 03 terminals. Terminal Styles Inches (Millimeters) Base & Rail Mount Connectors .40 (10.2) .12 (3.05) .03 (.79 .19 (4.8) .045 (1.14) .18 (4.6) .031 (.79) .062 (1.57) .70 (17.8) .125 (3.18) .045 (1.14) .03 (.7 .18 (4.6) .0 (.7 .18 (4.6) .18 (4.6) 01 Handwired #6-32 screw 51 #8-32 screw 02 Printed Circuit #6-32 screw 52 #8-32 screw 03 Non Feed-Thru #6-32 screw 53 #8-32 screw Available on Mount End (5) only. 07 Extended Pin #6-32 screw 57 #8-32 screw 14 Printed Circuit #6-32 screw 64 #8-32 screw Screw Options Power Distribution Blocks 07 Steel SEMS Zinc Plated 09 Brass SEMS Nickel Plated * NOTE: Wire ready screws standard on all terminal styles. CB3 Terminal Exit Options WIRE MANAGEMENT PRODUCTS Y Inches (Millimeters) .26 (6.60) .18 (4.6) X Exit Rear (std.) EB Exit Back 16 Series CB3000 Single Row Terminal Blocks Single & Double Row Filtered Connectors Hardware Options Solder Lugs .68 (17.3) (Bulk ordering part numbers are in parentheses.) Inches (Millimeters) Jumpers Quick Connects Blade Width A = .250”. Blade Width B = .187”. .84 (21.2) S1 (2S1) J201 Flat slip-on OJ3 A7 & B7 (2A7 & 2B7) A8 & B8 (2A8 & 2B8) A9 & B9 (2A9 & 2B9) Euro-MAG Series PCB – Spring Clamp OJ7 Mounting Options Right Angle Mounting Bracket End Positions usable Snap-in Angle Bracket A Exit Back (EB) Terminals Angle Bracket .24 (6.1) .42 (10.7) A Mounts blocks on PC boards at a right angle. • Protects solder joints. • Recommended for all EB (Exit Back) PCB terminal blocks. • Bracket snaps securely on block (no hardware required). • Minimum strip length (end positions are usable). • Mount with #6-32 or #8-32 screws (not supplied). Mounting Plates MOUNTING PLATE ; MP MP8 MT MT8 ; ; .71 (18.0) .79 (20.1) 1.02 (25.8) Inches (Millimeters) Base & Rail Mount Connectors Chassis or PCB #6 or #8 mounting screw & nut (Customer supplied.) .45 (11.4) Power Distribution Blocks Option AB WIRE MANAGEMENT PRODUCTS Options MP, MP8, MT & MT8 MP Metal inserts with .150” dia. hole accept #6 screw. MP8 Metal inserts with .187” dia. hole accept #8-32 screw. MT Metal inserts with tapped hole accept #6-32 screw. MT8 Metal inserts with tapped hole accept #8-32 screw. 17 MAGNUM ® Series A38 / B38 Single Row Terminal Blocks Single & Double Row Filtered Connectors Euro-MAG Series PCB – Spring Clamp SPECIFICATIONS Rating: A38: 30A, 600V B38: 50A, 300V Center Spacing: .437” (11.10 mm) Wire Range: A38: #10-22 AWG CU; B38: #8-16 AWG Screw Size: #8-32 Zinc Plated Steel Torque Rating: A38: 9 in-lb; B38: 15 in-lb for #8, 9 in-lb for #6 Base: A38 Only: Standoffs standard for easy flux washing B384104 Distance Between Barriers: .378” (9.60mm) Recommended PCB Hole Diameter (A38): .076” (1.93mm) Operating Temperature: 221°F (105°C) Molded Material: Black, UL Rated 94V0 Thermoplastic Breakdown Voltage: 5000V Agency Information: UL/CSA; CE Certified Series A38 TABLE A MOUNTING ENDS ONLY Poles 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 B Mount Ctrs. 1.31 1.75 2.19 2.62 3.06 3.50 3.93 4.37 4.81 5.24 5.68 6.12 6.56 6.99 7.43 “A” Dim. Length 1.67 2.10 2.54 2.98 3.41 3.85 4.29 4.72 5.16 5.60 6.04 6.47 6.91 7.35 7.78 BARRIER ENDS ONLY “A” Dim. Length 0.93 1.37 1.81 2.25 2.68 3.12 3.56 3.99 4.43 4.87 5.30 5.74 6.18 6.61 7.05 A382208 B Mount Centers A Dim. Length 9.0 [0.3 HOLE SIZE Ø5.0 [Ø0.20] 21.5 [0.85] 7.0 [0.28] 20.4 [0.80] 11.10 [0.437] Base & Rail Mount Connectors É”8.0 [0.31] 19.7 [0.78] A Dim. Length B Mount Centers 6.3 [0.25] * Dimensions in inches. To convert to millimeters, multiply by 25.4. Series B38 Power Distribution Blocks 13.0 [0.51] HOLE SIZE Ø5.0 [Ø0.20] 16.5 [0.65] 7.0 [0.28] 16.5 [0.65] 11.10 [0.437] WIRE MANAGEMENT PRODUCTS É”8.0 [0.31] 15.0 [0.59] 6.8 [0.27] 18 Part Numbering System Series Terminal Style Base/End # of Poles Screw Options Options Single & Double Row Filtered Connectors A38 1 2 7 9 - hand wired - printed circuit - extended wire wrap - .250" QC 1 - flat base, mount end 2 - flat base, barrier end 3 - insulator base* mount end 4 - insulator base* barrier end 02 to 16 Blank - standard screw (steel zinc plated, philslot BHMS) 04 - brass, nickel plated, philslot BHMS 07 - steel, SEMS zinc plated philslot screw 92 - steel, zinc plated slotted BHMS 94 - brass, nickel plated slotted BHMS L1 to L6 marking options (pg 22) RC - retaining clips (pg 15) Covers - (pg 23) R XX consult factory for terminal bend *N/A on 2 & 8 terminal styles. B38 Euro-MAG Series PCB – Spring Clamp 1 - long turret 2 - short turret 3 - screw terminal #6-32 screw top & bottom) 4 - stud (#8-32 screw top, #6-32 stud bottom) 5 - double stud (#6-32 stud top & bottom) 0 - flat base, mount ends 4 - insulator base, barrier ends 9 - insulator base mount ends 02 to 16 Blank - standard screw steel zinc plated philslot BHMS) 04 - brass, nickel plated, philslot BHMS 32 - #6-32 zinc plated steel philslot BHMS* 34 - #6-32 nickel plated brass philslot BHMS* 92 - steel, zinc plated slotted BHMS 94 - brass, nickel plated slotted BHMS L1 to L6 marking options (pg 23) RC - retaining clips (pg 16) Covers - (pg 23) *Note: 32 & 34 screws only *available with 3 terminal style. A38 Terminal Styles Wire ready screws standard Base & Rail Mount Connectors .55 (14.0) .031 (.79) .031 (.79) .110 (2.80) .062 (1.58) .20 (5.1) .031 (.79) .59 (15.1) .67 (17.0) .062 (1.58) .031 (.79) .250 (6.35) 1 Handwired 2 Printed Circuit 7 Extended Pin 9 .250” QC B38 Terminal Styles Power Distribution Blocks #6 - 32 SCREW #6 - 32 NUT .21 (5.3) 7.6 (.30) 4.6 (0.18) 11.6 (0.46) 6.4 (0.25) 4.6 (0.18) .58 (4.8) 6.8 (0.27) #6 - 32 SCREW #6 - 32 NUT .58 (4.8) #6 - 32 NUT 1 Long Turret 2 Short Turret 3 Screw Terminal 4 Stud 5 Double Stud Screw Options WIRE MANAGEMENT PRODUCTS Standard Zinc Plated Steel 04 Brass Nickel Plated 07 Steel SEMS Zinc Plated 32 Zinc Plated Steel Philslot BHMS 34 Nickel Plated Brass Philslot BHMS 92 Slotted, Zinc Plated Steel 94 Slotted, Nickel Plated Brass 19 MAGNUM ® A481307 Series A4000 & Series B4000 Single Row Terminal Blocks Single & Double Row Filtered Connectors SPECIFICATIONS Rating: See table. Center Spacing: .562” or 9/16” (14.28 mm) Wire Range: See rating table. Screw Size: #8-32 or #10-32 zinc plated slotted screws Torque Rating: #8 screw size 16 in-lb.; #10 screw size 20 in-lb. Distance Between Barriers: .47” (11.9 mm) Operating Temperature: 105°C (221°F) max., -40°C (-40°F) min. Molded Material: Black, UL Rated 94V0 Thermoplastic Hardware: Bottom studs supplied with nuts assembled. Cup washers are optional on bottom studs but are not recommended with ring terminals. Extended Hex Nuts: Optional extended, slotted hex nuts enable easier installation and removal with hex wrench or screwdriver. Available in bulk for the #10-32 studs on Series A4953 blocks. Specify part no. F582 and quantity. Breakdown Voltage: 6100V Agency Information: UL/CSA; CE Certified RATING TABLE Part Number A4003XX A4011XX A4013XX A4021XX A4035XX A4041XX A4043XX A4051XX A4803XX A4813XX A4843XX A4953XX B4843XX Terminal Top # 8 Screw # 8 Screw # 8 Screw # 8 Screw # 8 Screw #10 Screw #10 Screw #10 Screw #10 Screw #10 Screw #10 Screw #10 Stud #10 Screw Terminal Bottom #8 Stud Solder Solder .250 QC Closed Solder Solder 250 QC #8 Stud SolderTurret #8 Screw #10 Stud #8 Screw Wire* Range CU 8-16 AWG 10-16 AWG 10-16 AWG 10-16 AWG 8-16 AWG 10-16 AWG 10-16 AWG 10-16 AWG 8-16 AWG 10-16 AWG 8-16 AWG 8-16 AWG 8-16 AWG Ratings* 150V; 50 amps 600V; 35 amps 600V; 35 amps 600V; 35 amps 600V; 50 amps 600V; 35 amps 600V, 35 amps 600V; 35 amps 150V; 50 amps 600V; 35 amps 150V; 50 amps 150V; 50 amps 600V; 50 amps B484304 A40110407 Euro-MAG Series PCB – Spring Clamp A4000 Series .562 (14.27) .31 (7.9) A B .87 (22.1) .21 (5.3) #8-32 or #10-32 THD’S .31 (7.9) Base & Rail Mount Connectors 1.05 (26.7) .36 dia. (9.1) .57 (14.5) Note: Above unit supplied with nuts assembled. Cup washers are optional. Power Distribution Blocks * All models 30A Max. with 10 AWG; 35-50A ratings with 8 AWG using ring or fork type terminals. Note: 50A rating achieved with #8 copper wire crimped to ring terminal. Optional Cup Washers Assembled Available on A4003, A4803, A4843, A4953 & B4843. CUP WASHERS Poles A (in.) Mount Centers 1.69 2.25 2.81 3.37 3.93 4.50 5.06 5.62 6.18 6.74 7.31 7.87 8.43 8.99 9.55 10.12 10.68 B (in.) Length 2.12 2.68 3.24 3.80 4.36 4.93 5.34 6.05 6.61 7.17 7.74 8.30 8.86 9.44 9.98 10.55 11.11 WIRE MANAGEMENT PRODUCTS 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Reference Panel Cutout for 6 Position Block .20 DIA. (5.1) .75 (19.1) 3.31 (84.1) 3.93 (99.8) * Dimensions in inches. To convert to millimeters, multiply by 25.4. 20 Part Numbering System Series Terminal Style Base/End Poles Screw Options Options A4 B4 ss A4 - standard B4 - barrier 00 01 02 03 04 05 80 - screw top; stud bottom 1 - flat base/ - screw top; solder bottom mount end - #8 screw top; .250 QC bottom 3 - insulator base/ - screw top only mount end - #10 screw top; solder term. b. 5 - closed base/ - #10 screw top; .250 QC bottom mount end - screw top; stud bottom insulated base 81 - screw top; solder turret bottom 84 - screw top; screw bottom 95 - stud top; stud bottom 02 to 18 Blank - std. screw A1 to A9 - .250” QC 00 - screws shipped bulk CW - cup washer (pg 20) 04 - brass nickel plated J301 - flat slip-on jumper (2 position only) 07 - steel SEMS zinc L1 to L6 marking options (pg 22) plated (not available S1 & S2 - solder lugs/flat with hardware options; not available on A4003, Covers - (pg 23) A4803, A4813, A4843, B4843) Single & Double Row Filtered Connectors Terminal Styles #8-32 SCREW #8-32 or #10-32 SCREW .94 (23.9) 1.99 (50.6) .04 (1.0) .43 (10.9) .04 (1.0) Inches (Millimeters) #8-32 or #10-32 SCREW 1.41 (35.8) .17 (4.3) 1.41 (35.8) Euro-MAG Series PCB – Spring Clamp #8-32 HEX NUT .41 (10.4) .43 (10.9) .36 (9.1) A4003XX #8-32 or #10-32 SCREW #8-32 SCREW (TYP) 1.56 (39.6) A4011XX (#8-32) A4041XX (#10-32) #10-32 SCREW A4013XX (#8-32) A4043XX (#10-32) #10-32 SCREW .94 (23.9) 1.99 (50.6) .80 (20.3) 1.85 (47.0) .03 (.8) .59 (15.0) .250 (6.35) #8-32 HEX NUT .41 (10.4) TURRET .36 (9.1) A4021XX (#8-32) A4051XX (#10-32) #10-32 SCREW A4035XX #10-32 STUD A4803XX #10-32 SCREW A4813XX Base & Rail Mount Connectors 1.55 (39.4) 1.05 (26.7) 1.99 (50.6) .30 (7.6) .79 (20.1) 1.84 (46.7) .49 (12.5) #8-32 SCREW #10-32 HEX NUT .41 (10.4) .94 (23.9) .09 (2.4) #8-32 SCREW .41 (10.4) A4843XX A4953XX B4843XX Hardware Options Solder Lugs .56 (14.3) (Bulk ordering part numbers are in parentheses.) Inches (Millimeters) Power Distribution Blocks Jumpers Quick Connects Blade Width A = .250”. (For other orientations, contact factory.) S1 (2S1) 1.12 (28.4) J301 A1 (4A1) A2 (4A2) A3 (4A3 ) WIRE MANAGEMENT PRODUCTS S2 (2S2) A4 (4A4) A5 (4A5) A6 (4A6) A7 (4A7) A8 (4A8) A9 (4A9) 21 MAGNUM ® All Series Marking Options Single Row Terminal Blocks Single & Double Row Filtered Connectors Marking Options & Accessories Standard Marking Markings are applied directly to the sides of Series 1000, 2000, 3000, & 4000. Standard characters are white and 1/8” high. Factory may substitute 3/32” high characters. Standard marking this side Blocks to be marked on both sides require a different code for each side. Example: “L1” on one side of the block requires “L2” on the other side to ensure common terminal marking. Specify by adding suffix to part no. Euro-MAG Series PCB – Spring Clamp 1 3 L1 Upright Numerals Left to Right L2 Upright Numerals Right to Left L3 Left Lying Numerals Left to Right L4 Right Lying Numerals Right to Left L5 Upside-Down Numerals Right to Left L6 Upside-Down Numerals Left to Right Special Marking Special markings are available for Series 1000, 2000, 3000, 4000 & 5000 at an additional charge for preparation. Production charges for setup, handling and marking are the same as for standard marking and the same quantity discounts apply. Consult factory for price and delivery. Base & Rail Mount Connectors ❹ ✙ A¤ RE BL D BL K U ℡ Ω % # Closed Barrier Terminal Block Marking Options L1 L2 L3 L4 L5 L6 & LT1 = Upright numerals, numbered from left to right & LT2 = Upright numerals, numbered from right to left = Left lying numerals, numbered from left to right = Right lying numerals, numbered from right to left & LT5 = Upside down numerals, numbered from right to left & LT6 = Upside down numerals, numbered from left to right Options LT1 - LT6 Top Marking For high visibility in tight packages. 6 5 4 3 2 1 8 7 8 7 6 5 4 3 2 1 Power Distribution Blocks Marker Strips Black marker strips with white numerals mount beneath the terminal blocks to clearly identify terminal and wire positions. Available with forward or reverse markings, top or bottom of strip. If special markings are required, submit a drawing. 1 1 2 2 3 3 4 4 1 1 2 2 3 3 4 4 4 4 3 3 2 2 1 1 4 4 3 3 Options L1 - L6 Regular Marking 2 2 Bottom Forward - BF Top Forward - TF Bottom Reverse - BR Top Reverse - TR Series WIRE MANAGEMENT PRODUCTS Base Poles Marking MS MS1 - 1000 Series MS2 - 2000 Series MS3 - 3000 Series 1 2 3 4 5 - mount end, feed thru - barrier end, feed thru - mount end, insulator tubes - barrier end, insulator tubes - mount end, non feed-thru 02 to 36 BF - bottom forward TF - top forward BR - bottom reverse TR - top reverse 22 3 1 3 2 2 2 2 2 1 3 3 1 1 3 2 1 1 1 All Series Accessories Single Row Terminal Blocks Continued Single & Double Row Filtered Connectors Cover Options - Single Row Terminal Block Covers Available for Series A1000, A2000, A3000, A4000, CB2000, CB3000, LP2000, & LP3000. Three styles of UL 94V0 thermoplastic covers are offered in yellow or black. Covers are ordered separately and supplied with two clips each, unless ordered without clips. Optional markings may be specified (black on yellow; white on black). Notes: Covers can not be used with mounting plate options MP & MT. Covers can not be used with certain quick connect terminals. Covers can not be used with 0, 6, & 9 base/end styles on A2 or A3 Bulk Cover Clips: Series 1000 = CC1; Series 2000 & 3000 = CC2; Series 4000 = CC4. Standard Cover Markings Top Forward - TF 1 1 2 2 3 3 4 4 Bottom Forward - BF Skirted Access Side Top Reverse - TR 4 4 3 3 2 2 1 1 Euro-MAG Series PCB – Spring Clamp Bottom Reverse - BR Skirted Access Side Cover Options BB & CB Skirted access on both sides. Cover Options BO & CO Skirted access on one side only. Cover Options BC & TC Open access on both sides. Base & Rail Mount Connectors Cover Series Poles Markings Options BB - skirted access, both sides, black CB - skirted access, both sides, yellow BO - skirted access, one side, black CO - skirted access, one side, yellow BC - open access, both sides, black* TC - open access, both sides, yellow* * Not available in 4000 Series 1 2 3 4 - 1000 - 2000 - 3000 - 4000 02 to 36 BF - bottom forward TF - top forward BR - bottom reverse TR - top reverse 00 - without clips Power Distribution Blocks Snap-On Covers for A38/B38/F38 Series & CB2/CB3 Series A38/B38 Series CB2/CB3 Series WIRE MANAGEMENT PRODUCTS T A8 sss T B8 sss FB8 sss - Poles A38 Series B38 Series F38 Series T O2 T O3 - Poles CB2 Series CB3 Series 23