PRODUCT
SPECIFICATION
DATE: 05/04/2005 NO. 61L04008 REV. 2 SHEET 1 OF 9
cosmo
ELECTRONICS CORPORATION
SMD LED :
KL195W07
Features
Package: 1.6x0.8x0.6mm(0603) standard package Feature of the device: extremely wide viewing angle; ideal for backlighting and coupling in light guides Wavelength: 630nm(red),570nm(Yellow green) Viewing angle: Extremely Wide( 130°) Grouping parameter: luminous intensity Assembly methods: suitable for all SMT assembly methods Soldering methods: IR reflow soldering Taping: Package in 8mm tape on 7” diameter reel
Package Dimensions
PRODUCT
SPECIFICATION
DATE: 05/04/2005 NO. 61L04008 REV. 2 SHEET 2 OF 9
cosmo
ELECTRONICS CORPORATION
SMD LED :
KL195W07
Absolute Maximum Ratings At Ta = 25˚C
Parameter KL-195W07 R Power Dissipation 72 Peak Forward Current 100 (1/10 Duty Cycle, 0.1ms Pulse Width) Forward Current Reverse Voltage Operating Temperature Range Storage Temperature Range Wave Soldering Condition 30 5 -25˚C ~+ 80˚C -30˚C ~+ 85˚C 260˚C For 5 Seconds mA V mA 72 YG mW Unit
PRODUCT
SPECIFICATION
DATE: 05/04/2005 NO. 61L04008 SHEET 3 OF 9 REV. 2
cosmo
ELECTRONICS CORPORATION
SMD LED :
KL195W07
Electrical & Optical Characteristics At Ta = 25˚C
Parameter Luminous Intensity Red Yellow Green Iv KL-195W07 20 2θ 1/2 λd Δλ VF Ir Red/ Yellow Green Red Yellow Green Red Yellow Green Red Yellow Green Red/ Yellow Green 40 130 630 570 20 20 2.0 2.1 2.6 2.6 deg nm nm V Symbol PART NO Min. Typ. Max. Unit 25 50 mcd Test Condition IF = 20mA Note 1
Viewing Angle Dominant Wavelength Spectral Line Half-Width Forward Voltage Reverse Current
Note :
Note 2 IF = 20mA Note 3 IF = 20mA VR = 5V
100 μ A
1. Luminous intensity is measured with a photo detector and filter combination that follows the CIE ete - response curve. And the equipment measured luminous intensity torellance is ±5%. 2. θ1/2 is the off - axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the color of the device. 4. Caution in ESD:Static Electricity maybe cause damages to the LED. It is recommend to use a wrist band oranti - electrostatic glove when handing the LED. All devices, equipment and machinery must be properly grounded.
PRODUCT
SPECIFICATION
DATE: 05/04/2005 NO. 61L04008 SHEET 4 OF 9 REV. 2
cosmo
ELECTRONICS CORPORATION
SMD LED :
KL195W07
Test Condition IF=20mA VR=5V IF=20mA
The Reliability criteria of SMD LED
Item Forward Voltage Reverse Current Light Integrity Symbol VF IR Φv Limit Min – – ITV*0.7 Max U.S.L*1.1 U.S.L*2.0 –
*U.S.L: Upper Standard Level *ITV : Initial Test Value
Results of Reliability Test
ClassiNO fication Life Test 1 Test Item Standard Test Method Test Condition Test Sample Ac/Re Hours/Cycles NO 1000 HRS 1000HRS 22 PCS 22 PCS 22 PCS 22 PCS 22 PCS 22 PCS 22 PCS 22 PCS 0 / 22 0 / 22
Operating Constant urrent=20mA MIL-STD-750D1026 Life Test TA = 25OC
High 2 Temperature MIL-STD-883:1008 Temperature=105OC±5 OC Storage Low 3 Temperature Storage High Temperature 4 / High Humidity Temperature Cycling 5 Test 6 MIL-STD-883:1009 Temperature=-55OC±5 OC
Environment Test
1000HRS
0 / 22
MIL-STD-883E
TA = 85 OC
85%RH
1000HRS
0 / 22
MIL-STD-202:107D 105 OC~25 OC~-55 OC~25 OC MIL-STD-750:1051 30mins~5mins~30mins~5mins MIL-STD-883:1010
10Cycles
0 /22
MIL-STD-202:107D Thermal 85 OC±5 OC &- 40 OC±5 OC MIL-STD-750:1051 Shock Test (10mins) (10mins) MIL-STD-883:1011 Resistance MIL-STD-202:210A Soldering TA = 260±5 OC MIL-STD-750:2031 Heat Test MIL-STD-883E Method 2003.7 TA =230OC±5 OC
100Cycles Time= 10 sec±1sec Time= 5 sec±1sec
0 /22
Mechanical Test
7
0 /22
8 Solderability
0 /22
PRODUCT
SPECIFICATION
DATE: 05/04/2005 NO.61L04008 REV. 2 SHEET 5 OF 9
cosmo
ELECTRONICS CORPORATION
SMD LED :
KL195W07
Typical Electro-Optical Characteristics Curves (25oC Ambient Temperature Unless Otherwise Noted)
RELATIVE INTENSITY VS. WAVELENGTH
yellow green
100 80 Irel 60 40 20 0 400
red
450
500
550 λ
600
650
700
FORWARD CURRENT VS. FORWARD VOLTAGE
RELATIVE LUMINOUS INTENSITY VS. FORWARD CURRENT
2
50 40
1.5 Iv 1
RED YELLOW GREEN
IF 30 20 10 0 1.2 1.6 2.0 2.4 2.8 3.2 VF 3.6 4.0
0.5 0.0 0 10 20 30 IF 40
PRODUCT
SPECIFICATION
DATE: 05/04/2005 NO. 61L04008 SHEET 6 OF 9 REV. 2
cosmo
ELECTRONICS CORPORATION
40
SMD LED :
KL195W07
FORWARD CURRENT DERATING CURVE
SPATIAL DISTRIBUTION
0° 10° 20° 30° 40°
30 IF 25 20
50° 60° 70° 0.9
0 20 40 60 T 80 100 °C
1.0
10
80° 90° 0.7 0.5 0.3 0.1 0.2 0.4 0.6 0.8
0
Method of Taping / Polarity and Orientation
Packing unit 3000/reel
Unit : mm Direction
U: Taping upward Notes: All dimensions are in millimeters (inches)
D: Taping downward
PRODUCT
SPECIFICATION
DATE: 05/04/2005 NO. 61L04008 SHEET 7 OF 9 REV. 2
cosmo
ELECTRONICS CORPORATION
SMD LED :
KL195W07
Package Dimensions of Reel
Unit: mm
Packaging
Product lable
CUSTOMER: CUSTOMER P/N: DEVICE TYPE: BIN: COLOR RANK: LOT NO: QTY:
CAUTION: After open the aluminum laminate bag the lamps should be storage in the Follow condition Temperautre:5 to 30 OC,Humidity:70%,Storage time:72hrs max Backing condition :If backing is necessary , we recommended the backing condition is 60 +/- 5 OC 10hours
PRODUCT
SPECIFICATION
DATE: 05/04/2005 NO. 61L04008 REV. 2 SHEET 8 OF 9
cosmo
ELECTRONICS CORPORATION
SMD LED :
KL195W07
Packing
CUSTOMER: CUSTOMER P/N: DEVICE TYPE: BIN: COLOR RANK: LOT NO: QTY:
Cautions for use
Over-current-proof Customer must apply resistors for protection ,others slight voltage shit will cause big current change (Burn out will happen). Storage time The operation of temperature and RH are : 5 OC ~35 OC,RH60%. Once the package is opened , the products should be used within a week. Otherwise , they should be kept in a damp proof box with descanting agent. Considering the tape life , we suggest our customers to use our products within a year(from production date) If opened more than one week in an atmosphere 5 OC ~35 OC , RH60% , they should be treated at 60 OC ±5 OC for 15 hrs. COSMO-lnnotek will not be held responsible for any damage to the user that may result from accidents or any other reasons during operation of the user’s unit if use to exceed the absolute maximum ratings, or not keep the matters that demand special attention.
PRODUCT
SPECIFICATION
DATE: 05/04/2005 REV. 2 SHEET 9 OF 9 NO. 61L04008
cosmo
ELECTRONICS CORPORATION
SMD LED :
KL195W07
Others
Soldering Heat Reliability Available for Pb free soldering process Please refer to the following figure :
5 sec Temp (°C) 260 230 4°C/s max Preheat
150 120
Time
60~120sec
30~50sec
Soldering Iron
Basic spec is ≦5sec when 260 OC. If temperature is higher, time shorter ( +10 OC → -1sec ). Power dissipation of Iron should be smaller than 15W, and temperature should be controllable. Surface temperature of the device should be under 230 OC.
Rework
Customer must finish rework within 5sec under 245 OC. The head of Iron can not touch copper foil. Twin-head type is preferred.
很抱歉,暂时无法提供与“KL195W07”相匹配的价格&库存,您可以联系我们找货
免费人工找货