9104-05-11

9104 SERIES/HIGH VOLTAGE SIP REED RELAYS 9104 Series Hi Voltage SIP Reed Relays Molded SIP relays are the industry standard when high reliability and consistent performance are desired in a compact package. The 9104 Series adds high voltage switching capability and high voltage standoff capability to a SIP relay package. These high voltage, high performance relays are ideally suited for Automatic Test Equipment, Instrumentation, Battery Management, Solar and Process Control applications where voltage isolation is a key design requirement. 9104 Series Features u High voltage switching up to 1000 V u High dielectric strength (up to 4000 V DC) u High Insulation Resistance – 1011Ω minimum u High reliability, hermetically sealed contacts for long life u High speed switching compared to electromechanical relays u Molded thermoset body on integral lead frame design u Optional Coil Suppression Diode – protects coil drive circuits u Magnetic Shield – reduces interaction u UL File #E67117 - Contact factory for details u RoHS compliant DIMENSIONS in Inches (Millimeters) TOP VIEW PIN #1 .103 Typ. (2.6) .120 (3.0) .154 Typ. (3.9) .950 Max. (24.13) .245 Max. (6.22) .320 Max. (8.13) .020 Typ. .(.51) 3 1 .300 (7.62) 5 .200 (5.08) 7 .018 Typ. (.46) .300 (7.62) .125 ± .005 (3.17 ± .13 ) .010 Typ. (.25) Ordering Information Part Number Model Number 9104 9XXX-XX-XX Coil Voltage 05=5 volts 12=12 volts General Options 0=No Diode 1=Diode2 Dielectric Contacts Strength (Min) Shield to Coil 1=2000/3000 3=3000/3000 4=4000/4000 08242018 tel: (4 (401) 943 943.2686 | fa fax: (4 (401) 942 942.09 092 20 MODEL NUMBER Parameters COIL SPECS. 91042 Test Conditions Units 4 Pin SIP Nom. Coil Voltage VDC 5 12 5 12 Max. Coil Voltage VDC 6.5 15.0 6.5 15.0 +/- 10%, 25° C Ω 175 500 140 500 Operate Voltage Must Operate by VDC - Max. 3.75 9.0 3.75 9.0 Release Voltage Must Release by VDC - Min. 0.5 1.0 0.5 1.0 Coil Resistance CONTACT RATINGS Switching Voltage3 Max DC/Peak AC Resist. Volts 1000 Switching Current Max DC/Peak AC Resist. Amps 0.5 Carry Current Max DC/Peak AC Resist. Amps 1.3 Contact Rating Max DC/Peak AC Resist. Watts 10 Life Expectancy-Typical1 Signal Level 1.0V, 10mA x 106 Ops. 300 Static Contact Resistance (max. init.) 50mV, 10mA Ω 0.150 Dynamic Contact Resistance (max. init.) 0.5V, 50mA at 100 Hz, 1.5 msec Ω 0.200 Insulation Resistance (minimum) Between all Isolated Pins at 100V, 25°C, 40% RH Ω 1011 Capacitance - Typical Across Open Contacts No Shield pF 1.0 Open Contact to Coil No Shield pF - Between Contacts Contacts/Shield to Coil VDC/peak AC VDC/peak AC At Nominal Coil Voltage, 30 Hz Square Wave msec. 0.75 msec. 0.5 RELAY SPECIFICATIONS Dielectric Strength (minimum) 4 Operate Time including bounce - Typical Release Time - Typical Top View: Dot stamped on top of relay refers to pin #1 location Grid = .1”x.1” (2.54mm x 2.54mm) 2000 / 3000 2000 / 3000 4000 4000 1 3 5 Notes: Consult factory for life expectancy at other switching loads. Optional diode is connected to pin #3(+) and pin #5(-). Correct coil polarity must be observed. 3 Switch current limited to 1.0mA @ 1000V. 1 7 2 4 Dielectric Strength 9104-XX-1X 9104-XX-3X 9104-XX-4X VDC/peak AC 2000/3000 3000/3000 4000/4000 Environmental Ratings: Storage Temp: -35°C to +100°C; Operating Temp: -20°C to +85°C; Solder Temp: 270°C max; 10 sec. max All electrical parameters measured at 25°C unless otherwise specified. Vibration: 20 G’s to 2000 Hz; Shock: 50 G’s 08242018 For most recent data visit www.cotorelay.com COTO TECHNOLOGY, INC.