C470RT230-S0200

RazerThin® LEDs CxxxRT230-S0200 Cree’s RazerThin LEDs combine highly efficient InGaN materials with Cree’s proprietary G•SiC® substrate to deliver superior price/performance for blue and green LEDs. These vertically structured LED chips are small in size and require a low forward voltage. Cree’s RT series chips are tested for conformity to optical and electrical specifications and the ability to withstand 1000 V ESD. Applications include keypad backlighting where sub-miniaturization and thinner form factors are required. FEATURES • • Small Chip - 200 x 200 x 85 μm Low Forward Voltage – – 3.1 V Typical at 20 mA - Blue & Traffic Green 3.2 V Typical at 20 mA Green 2.0 mW min. Blue 1.5 mW min. Green APPLICATIONS • Mobile Phone Key Pads   Blue LEDs White LEDs • • • Audio Product Display Lighting Mobile Appliance Keypads Automobile Dashboard Lighting • RT230™ LED Performance – – • • Single Wire Bond Structure Class 2 ESD Rating CxxxRT230-S0200 Chip Diagram Top View G•SiC® LED Chip 200 x 200 μm Mesa (junction) 176 x 176 μm Gold Bond Pad 105 μm Diameter Bottom View Side View A PR3CO, Rev. Datasheet: C InGaN Anode (+) SiC Substrate h = 85 μm Backside Metallization 80 x 80 μm Cathode (-) Subject to change without notice. www.cree.com  Maximum Ratings at TA = 25°C Notes &3 DC Forward Current Peak Forward Current (1/10 duty cycle @ 1kHz) LED Junction Temperature Reverse Voltage Operating Temperature Range Storage Temperature Range Electrostatic Discharge Threshold (HBM) Note 2 Note 2 CxxxRT230-S0200 30 mA 100 mA 125°C 5V -40°C to +100°C -40°C to +100°C 1000 V Class 2 Note 3 Electrostatic Discharge Classification (MIL-STD-883E) Typical Electrical/Optical Characteristics at TA = 25°C, If = 20 mA Part Number Forward Voltage (Vf, V) Min. C460RT230-S0200 C470RT230-S0200 C505RT230-S0200 C527RT230-S0200 Mechanical Specifications Description P-N Junction Area (μm) Top Area (μm) Bottom Area (μm) Chip Thickness (μm) Au Bond Pad Diameter (μm) Au Bond Pad Thickness (μm) Back Contact Metal Area (μm) 2.7 2.7 2.7 2.7 Typ. 3.1 3.1 3.1 3.2 Max. 3.7 3.7 3.7 3.7 Reverse Current [I(Vr=5V), μA] Max. 2 2 2 2 Full Width Half Max (λD, nm) Typ. 21 22 30 35 CxxxRT230-S0200 Dimension 176 x 176 200 x 200 200 x 200 85 105 1.2 80 x 80 Tolerance ± 25 ± 25 ± 25 ± 10 -5, +15 ± 0.5 ± 25 Notes: 1. 2. 3. 4. 5. Maximum ratings are package dependent. The above ratings were determined using a T-1 3/4 package (with Hysol OS4000 epoxy) for characterization. Ratings for other packages may differ. The forward currents (DC and Peak) are not limited by the die but by the effect of the LED junction temperature on the package. The junction temperature limit of 125°C is a limit of the T-1 3/4 package; junction temperature should be characterized in a specific package to determine limitations. Assembly processing temperature must not exceed 325°C (< 5 seconds). Product resistance to electrostatic discharge (ESD) according to the HBM is measured by simulating ESD using a rapid avalanche energy test (RAET). The RAET procedures are designed to approximate the maximum ESD ratings shown. The RAET procedure is performed on each die. The ESD classification of Class 2 is based on sample testing according to MIL-STD-883E. All products conform to the listed minimum and maximum specifications for electrical and optical characteristics when assembled and operated at 20 mA within the maximum ratings shown above. Efficiency decreases at higher currents. Typical values given are within the range of average values expected by manufacturer in large quantities and are provided for information only. All measurements were made using lamps in T-1 3/4 packages (with Hysol OS4000 epoxy). Optical characteristics measured in an integrating sphere using Illuminance E. Caution: To obtain optimum output efficiency, the amount of epoxy used should be characterized based upon the specific application. Specifications are subject to change without notice. Copyright © 2005-2006 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo, G•SiC and RazerThin are registered trademarks, and RT230 is a trademark of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com 2 CPR3CO Rev. A Standard Bins for CxxxRT230-S0200 LED chips are sorted to the radiant flux and dominant wavelength bins shown. Sorted die sheets contain die from only one bin. Sorted die kit (CxxxRT230-S0200) orders may be filled with any or all bins (CxxxRT230-0xxx) contained in the kit. All radiant flux values are measured at If = 20 mA and all dominant wavelength values are measured at If = 20 mA. C460RT230-S0200 C460RT230-0203 C460RT230-0201 C460RT230-0204 C460RT230-0202 6.0 mW Radiant Flux 4.0 mW 2.0 mW 455 nm 460 nm Dominant Wavelength C470RT230-S0200 465 nm 6.0 mW Radiant Flux 4.0 mW C470RT230-0203 C470RT230-0201 C470RT230-0204 C470RT230-0202 2.0 mW 465 nm 470 nm Dominant Wavelength C505RT230-S0200 475 nm 6.0 mW Radiant Flux 4.0 mW 2.5 mW C505RT230-0205 C505RT230-0203 C505RT230-0201 C505RT230-0206 C505RT230-0204 C505RT230-0202 1.5 mW 500 nm 505 nm Dominant Wavelength C527RT230-S0200 510 nm Radiant Flux 4.0 mW 2.5 mW C527RT230-0204 C527RT230-0201 C527RT230-0205 C527RT230-0202 C527RT230-0206 C527RT230-0203 1.5 mW 520 nm 525 nm 530 nm 535 nm Dominant Wavelength Copyright © 2005-2006 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo, G•SiC and RazerThin are registered trademarks, and RT230 is a trademark of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com 3 CPR3CO Rev. A Characteristic Curves These are representative measurements for the RT230 product. Actual curves will vary slightly for the various radiant flux and dominant wavelength bins. Wavelength Shift vs Forward Current 20.0 527nm 25 Forward Current vs Forward Voltage 30 16.0 505nm 470nm 20 12.0 Shift (nm) If (mA) 15 8.0 4.0 10 0.0 5 -4.0 0 0.0 0 0.5 1.0 1.5 2.0 2.5 Vf (V) 3.0 3.5 4.0 4.5 5.0 5 10 15 If (mA) 20 25 30 Relative Intensity vs Forward Voltage 140 100 Relative Intensity vs. Peak Wavelength 460 nm 120 80 505 nm 527 nm Relative Intensity (%) % Relative Intensity 100 60 80 60 40 40 20 20 0 0 5 10 15 If (mA) 20 25 30 0 350 400 450 500 Wavelength (nm) 550 600 650 Copyright © 2005-2006 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo, G•SiC and RazerThin are registered trademarks, and RT230 is a trademark of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com 4 CPR3CO Rev. A