C LD-DS41 Rev 1A
Product family data sheet
cree Xlamp Xt-e leds
®
®
Product descriPtion
XLamp LeD Cree’s XT-e is Cree’s highest in performing silicon carbide-based technology, delivered industry-standard XP/XT
features
• Available in white, 80-CRI min white, 70-min CRI white and royal blue Binned at 85 °C Cool white efficacy of up to 148 lm/W (@ 85 °C, 350 mA) Royal Blue wall plug efficiency of up to 53% (@ 85 °C, 350 mA) Wide viewing angle: 115-140° Thermal resistance: 5 °C/W Maximum drive current: 1.5 A electrically neutral thermal path vf binning supported for XT-e White and Royal Blue XT-e Royal Blue sorted into 2.5-nm-wavelength bins Unlimited floor life at ≤ 30 ºC/85% RH Reflow solderable - JEDEC J-STD-020C Compatible RoHS- and REACH-compliant
taBle of contents
Product Characteristics ............... 2 Flux Characteristics ................... 2 Relative Spectral Power Distribution............................... 4 Relative Flux vs. Junction Temperature ............................. 5 electrical Characteristics ............. 6 Relative Flux vs. Current ............ 6 Relative Chromaticity vs. Temperature and Current............ 8 Typical Spatial Distribution .......... 9 Thermal Design ........................10 Reflow-Soldering Characteristics .10 Notes ......................................11 Mechanical Dimensions..............12 Tape and Reel ..........................13 Packaging ................................14
• • •
packaging.
XT-e White sets the
new standard for high performance and dramatically lowers system cost. blue XT-e Royal Blue is Cree’s light for remote-phosphor • • LeDs and bring quality high of • • • • • highest performing source of royal applications. Cree XLamp
performance light to applications, and and personal, studio,
a wide range of lighting including outdoor, remoteindoorand
phosphor, color-changing, portable directional, transportation, stage commercial emergency-vehicle lighting. WWW.CRee.COM/XLAMP
•
•
note: for remote phosphor applications, a separate license to certain cree patents is required.
Cree, Inc. Cree, Inc. 4600 Silicon Drive 4600 Silicon Drive Durham, NC 27703 Durham, NC 27703 USA Tel: +1.919.313.5300 USA Tel: +1.919.313.5300 www.cree.com/xlamp
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
x lamp xT-E lEDs
Product characteristics
characteristics Thermal resistance, junction to solder point Viewing angle (FWHM) - white Viewing angle (FWHM) - royal blue Temperature coefficient of voltage ESD classification (HBM per Mil-Std-883D) DC forward current Reverse voltage Forward voltage (@ 350 mA, 85 °C) LeD junction temperature mA v v °C 2.85 unit °C/W degrees degrees mv/°C minimum typical 5 115 140 -2.5 Class 2 1500 5 3.4 150 maximum
fluX characteristics - White (tJ = 85 °c)
The following table provides several base order codes for XLamp XT-e White LeDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp XT-e Binning and Labeling document.
color
cct range min. max.
Base order codes minimum luminous flux @ 350 ma (lm) Group R5 flux (lm) 139 130 122 139 130 122 122 114 107 122 114 107
calculated minimum luminous flux (lm)* 700 ma 247 231 217 247 231 217 217 203 190 217 203 190 1500 ma 420 393 369 420 393 369 369 354 324 369 354 324
order code
XTEAWT-00-0000-000000H51 XTeAWT-00-0000-000000G51 XTeAWT-00-0000-000000F51 XTEAWT-00-0000-000000HE3 XTeAWT-00-0000-000000Ge3 XTeAWT-00-0000-000000Fe3 XTeAWT-00-0000-00000LFe4 XTeAWT-00-0000-00000Lee4 XTeAWT-00-0000-00000LDe4 XTeAWT-00-0000-00000BFF5 XTeAWT-00-0000-00000BeF5 XTeAWT-00-0000-00000BDF5
Cool White
5,000 K
8,300 K
R4 R3 R5
Outdoor White
4,000 K
6,200 K
R4 R3 R3
Neutral White
3,700 K
5,000 K
R2 Q5 R3
70 CRI Minimum Neutral White
3,700 K
5,000 K
R2 Q5
Notes: • Cree maintains a tolerance of ±7% on flux and power measurements and ±2 on CRI measurements. • Typical CRI for Neutral White, 3700 K - 5000K CCT is 75. • Typical CRI for Warm White, 2600 K - 3700 K CCT is 80. • Calculated flux values are for reference only
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
2
x lamp xT-E lEDs
color
cct range min. max.
Base order codes minimum luminous flux @ 350 ma (lm) Group Q5 flux (lm) 107 100 93.9 107 100 93.9 114 107 100
calculated minimum luminous flux (lm)* 700 ma 190 178 167 190 178 167 190 178 167 1500 ma 324 302 284 324 302 284 324 302 284
order code
XTEAWT-00-0000-00000HDE7 XTEAWT-00-0000-00000HCE7 XTEAWT-00-0000-00000HBE7 XTeAWT-00-0000-00000LDe7 XTeAWT-00-0000-00000LCe7 XTeAWT-00-0000-00000LBe7 XTeAWT-00-0000-00000Bee7 XTeAWT-00-0000-00000BDe7 XTeAWT-00-0000-00000BCe7
80 CRI Minimum White
2,600 K
4,300 K
Q4 Q3 Q5
Warm White
2,600 K
3,700 K
Q4 Q3 R2
70 CRI Minimum Warm White
2,600 K
3,700 K
Q5 Q4
Notes: • Cree maintains a tolerance of ±7% on flux and power measurements and ±2 on CRI measurements. • Typical CRI for Neutral White, 3700 K - 5000K CCT is 75. • Typical CRI for Warm White, 2600 K - 3700 K CCT is 80. • Calculated flux values are for reference only
fluX characteristics - royal Blue (tJ = 85 °c)
The following table provides order codes for XLamp XT-e Royal Blue LeDs. Additional information on the performance grouping and codes for XT-e Royal Blue LeDs can be found in the XT-e Binning and Labeling document.
dominant Wavelength range min. dWl (nm)
D36 D36 D46 D36 D46 D56 D37 D47 D37 450 450 455 450 455 460 452.5 457.5 452.5 D57 D47 D57 D37 D47 D57 D46 D56 D56
dWl Kit codes
order codes, minimum radiant flux @ 350 ma, tj=85 °c
max. dWl (nm)
465 460 465 455 460 465 457.5 462.5 462.5
475 mW
XTeARY-00-0000-000000K01 XTeARY-00-0000-000000K02 XTeARY-00-0000-000000K03 XTeARY-00-0000-000000K04 XTeARY-00-0000-000000K05 XTeARY-00-0000-000000K06 XTeARY-00-0000-000000K07 XTeARY-00-0000-000000K08 XTeARY-00-0000-000000K09
500 mW
XTeARY-00-0000-000000L01 XTeARY-00-0000-000000L02 XTeARY-00-0000-000000L03 XTeARY-00-0000-000000L04 XTeARY-00-0000-000000L05 XTeARY-00-0000-000000L06 XTeARY-00-0000-000000L07 XTeARY-00-0000-000000L08 XTeARY-00-0000-000000L09
525 mW
XTeARY-00-0000-000000M01 XTeARY-00-0000-000000M02 XTeARY-00-0000-000000M03 XTeARY-00-0000-000000M04 XTeARY-00-0000-000000M05 XTeARY-00-0000-000000M06 XTeARY-00-0000-000000M07 XTeARY-00-0000-000000M08 XTeARY-00-0000-000000M09
550 mW
XTeARY-00-0000-000000N01 XTeARY-00-0000-000000N02 XTeARY-00-0000-000000N03 XTeARY-00-0000-000000N04 XTeARY-00-0000-000000N05 XTeARY-00-0000-000000N06 XTeARY-00-0000-000000N07 XTeARY-00-0000-000000N08 XTeARY-00-0000-000000N09
01 02 03 04 05 06 07 08 09
Note: Cree maintains a tolerance of ±7% on flux and power measurements
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
3
x lamp xT-E lEDs
Relative PoWer distriBution - White relative sPectral Spectral Power
100
Relative Radiant Power (%)
80
60
5000K - 8300K CCT
2600K - 3700K CCT
40
20
0
400 450 500 550 600 650 700 750
Wavelength (nm)
relative sPectral PoWer distriBution - royal Blue
Relative Spectral Power
100%
Relative Radiant Power (%)
80%
60%
40%
Royal Blue
20%
0% 400 450 500 550 600 650 700 750
Wavelength (nm)
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
4
x lamp xT-E lEDs
relative luminous fluX vs. Junction temPerature (if = 350
Relative Flux Output vs. Junction Temperaturea) - White m
120%
Relative Luminous Flux
100%
80%
60%
40%
20%
0%
25 50 75 100 125 150
Junction Temperature (ºC)
Relative Flux Output vs. Junction Temperature
120%
relative radiant fluX vs. Junction temPerature (if = 350
ma)
- royal Blue
Relative Radiant Flux
100%
80%
60%
40%
20%
0%
25 50 75 100 125 150
Junction Temperature (ºC)
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
5
x lamp xT-E lEDs
lectrical Characteristics (Tj = 85ºC) electrical characteristics (tJ = 85 °c)
1600
1400
Forward Current (mA)
1200 1000
800
600 400
200
0 2.50 2.75 3.00 3.25 3.50
Relative Intensity vs. Current (Tj = 85ºC)
relative luminous fluX vs. current (tJ = 85 °c) - White
Forward Voltage (V)
350%
Relative Luminous Flux (%)
300% 250% 200% 150% 100% 50% 0% 0 200 400 600 800 1000 1200 1400 1600
Forward Current (mA)
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
6
tive Radiant Flux vs. Current (Tj = 85ºC)
relative radiant fluX vs. current (tJ = 85 °c) - royal Blue
x lamp xT-E lEDs
350%
Relative Radiant Flux (%)
300% 250% 200% 150% 100% 50% 0% 0 200 400
Forward Current (mA)
600
800
1000
1200
1400
1600
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
7
x lamp xT-E lEDs
relative chromaticity vs. current and temPerature (Warm White)
Relative Chromaticity Vs. Current, WW
0.020
0.015 0.010
0.005
TJ = 85 °C
0.000
-0.005 -0.010
ΔCCx
ΔCCy
-0.015
-0.020
0
200 400 600 800 1000 Relative Chromaticity Vs. Temperature WW (mA) Current
1200
1400
1600
0.020 0.015 0.010
0.005 0.000
IF = 350 mA
ΔCCx
ΔCCy
-0.005 -0.010
-0.015 -0.020
0
20
40
60
80 Tsp (°C)
100
120
140
160
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
8
x lamp xT-E lEDs
Typical Spatial Radiation Pattern
tyPical sPatial distriBution - White
120
Relative Luminous Intensity (%)
100
80
60
40
20
0 -90 -70 -50 -30 -10 10 30 50 70 90
Angle (º)
ical Spatial Distribution
tyPical sPatial distriBution - royal Blue
120
Relative Luminous Intensity (%)
100
80
60
40
20
0 -90 -70 -50 -30 -10 10 30 50 70 90
Angle (º)
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
9
x lamp xT-E lEDs
thermal desiGn
ermal Design product to be designed in a manner that minimizes the thermal resistance from the solder point to crucial for the end
ambient in order to optimize lamp life and optical characteristics.
1600
The maximum forward current is determined by the thermal resistance between the LeD junction and ambient. It is
1400
Maximum Current (mA)
1200 1000 800 600 400 200
0
Rj-a Rj-a Rj-a Rj-a
= = = =
10°C/W 15°C/W 20°C/W 25°C/W
0
20
40
60
80
100
120
140
Ambient Temperature (ºC)
refloW solderinG characteristics
In testing, Cree has found XLamp XT-E LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment.
TP
Ramp-up
tP
Critical Zone TL to TP
Temperature
TL
Tsmax Tsmin ts
Preheat
tS
Ramp-down
25
t 25˚C to Peak
Time
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
10
x lamp xT-E lEDs
Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Preheat: Temperature Min (Tsmin) Preheat: Temperature Max (Tsmax) Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5 °C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25 °C to Peak Temperature
lead-Based solder 3 °C/second max. 100 °C 150 °C 60-120 seconds 183 °C 60-150 seconds 215 °C 10-30 seconds 6 °C/second max. 6 minutes max.
lead-free solder 3 °C/second max. 150 °C 200 °C 60-180 seconds 217 °C 60-150 seconds 260 °C 20-40 seconds 6 °C/second max 8 minutes max.
Note: All temperatures refer to the topside of the package, measured on the package body surface.
notes
Lumen Maintenance Projections Please read the XLamp Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LeD junction temperature. Moisture Sensitivity In testing, Cree has found XLamp XT-E LEDs to have unlimited floor life in conditions ≤30 ºC/85% relative humidity (RH). Moisture testing included a 168-hour soak at 85 ºC/85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. Cree recommends keeping XLamp LeDs in their sealed moisture-barrier packaging until immediately prior to use. Cree also recommends returning any unused LeDS to the resealable moisture-barrier bag and closing the bag immediately fter use. RoHS Compliance The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with eU Directive 2002/95/ EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. vision Advisory Claim WARNING: Do not look at exposed lamp in operation. eye injury can result. See LeD eye Safety at www.cree.com/ products/pdf/XLamp_eyeSafety.pdf.
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
11
3.30
x lamp xT-E lEDs
.650 .65 1.30
mechanical dimensions
1.15
6 5 4 3 2
REV 3 DESCRIPTION
R1.530
NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION 6 .60 CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT NOTICE 1.20 6 MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT .60 CONTAINED WITHIN ARE THE PROPRIETARY AND NOTICE OF CREE INC.
All measurements are ±.13 mm unless otherwise indicated. 5
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONTAINED WITHIN ARE THE PROPRIETARY AND UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT OF MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CREE INC. UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC.
5
4 4
B
REVISONS
B
3
REMOVED CHIP DIMENSIONS
REV
B
REV
R
B
D
3.30
3.20 1.60
D
1.65
D
.40 .40
3.450
.40 3.20
1.30 3.30 ENDED PCB SOLDER PAD
2.36
RECOMMENDED STENCIL PATTERN 3.450 (HATCHED AREA IS OPENING)
THIRD ANGLE PROJECTION
3.450
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 °
DRAWN BY
DATE
2.30 1.15
TITLE
.83
2.36
D. CRONIN ---
3/8/11
DATE
CHECK
4600 Silicon Drive Durham, N.C 27703 Phone (919) 313-5300 Fax (919) 313-5558
APPROVED
2.36
--
FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: 1.6
MATERIAL
.83
.50--
DATE
A 2.30
OUTLINE DRAWING XP HEW 1.15
SIZE
2.30
-- .83
FINAL PROTECTIVE FINISH
-2
C
24.000
DRAWING NO.
2610-00015 .50
.50
SHEET OF
1.15
REV.
B
SCALE
1 /1
C
5
4
3
1
3.450
C C
3.30
3.450 3.450
.650 R1.530 .65 1.30
top view
1.15 .65
B
side view
.60 1.20 R1.530
.650
Bottom view
.650
.65 .65 1.30 1.30
R1.530
.50
1.15 .65 1.15
3.30 1.65
.60
B
.50 B
.50
.65 .60
.40 .40 .40 3.20
.50
.60 1.20 .60 3.20 1.20
.60 1.60
.40 .50
.50
1.30 .50 3.30
3.30 1.65 1.65
3.20 .40 .40 1.60
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 °
3.30
3.20
DRAWN BY
DATE
A
RECOMMENDED PCB SOLDER PAD .40
RECOMMENDED STENCIL PATTERN .40 (HATCHED AREA IS OPENING)
1.60 .40
D. CRONIN
CHECK
3/8/11
DATE
-APPROVED
-DATE
.40
A A
6
.50
1.30 1.30 3.30
.40
THIRD ANGLE PROJECTION
-MATERIAL
--
TITLE
.50 3.30 5 RECOMMENDED PCB SOLDER PAD RECOMMENDED PCB SOLDER Pad recommended PcB solderPAD
4
SIZE -UNLESS OTHERWISE SPECIFIED D. CRON FINAL PROTECTIVE FINISH 3.20 DIMENSIONS ARE IN DRAWN CHECK MILLIMETERS AND AFTER FINISH. UNLESS OTHERWISE SPECIFIED SCALE RECOMMENDED STENCIL PATTERN D. C SURFACE FINISH: 1.6 --DIMENSIONS ARE IN24.000 -TOLERANCE UNLESS SPECIFIED: CHECK .XX ±AND .25 (HATCHED AREA IS OPENING) APPROVED MILLIMETERS AFTER FINISH. 3 2 RECOMMENDED STENCIL PATTERN .XXX UNLESS SPECIFIED: .125 TOLERANCE ± -X° .XX ±.5 ° .25 ± (HATCHED AREA IS OPENING) THIRD ANGLE PROJECTION APPROV .XXX ± FOR SHEET METAL PARTS.125 ONLY MATERIAL ± 1.5 .5 ° .X X° ± THIRD ANGLE PROJECTION .XX .75 FOR SHEET± METAL PARTS ONLY MATERI .XXX.X ± ± .25 1.5 FINAL PROTECTI X° .XX ±.5 ° .75 ±
3.20 .40
OUTLINE D
C
DRAWN BY DRAWING
recommended stencil Pattern (shaded area is open)
4
6 6
5 5
3 4 3
.XXX .6 SURFACE FINISH: 1± X° ±
.25 .5 ° SURFACE FINISH: 1.6
FINAL PRO
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
12
x lamp xT-E lEDs
taPe and reel
6
5
4
6
1.50 -.00[.0591-.0000]Do 2.00 [.079] P2 All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. P2
D
NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC.
NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT REV MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC.
3
5
2
REVISONS
DESCRIPTION
4
1
BY DATE APP'D
3
REV
2
DESCRIPT
+.10 +.0039
2.00 [.079]
1.50
+.10 +.0039
-.00[.0591-.0000]Do
D
4.00 [.157] Po
1.75 [.069] E1
4.00 [.157] Po
D
1.75 [.069] E1
All dimensions in mm.
6 5
NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC.
4
3
REV
2
REVISONS
DESCRIPTION BY
1
DATE APP'D
4.39 [.173]
3.78 [.149] Bo
5.50 [.217]F 10.25 [.404] E2
4.39 [.173] 12.00 [.472] NOMINAL 12.30 [.484] MAX W
5.50 [.217]F
1.50 +.10 +.0039 -.00[.0591-.0000]Do
C
12.00 [.472] NOMINAL 12.30 [.484] MAX W
2.00 [.079] P2
D
C 4.00 [.157] Po
1.75 [.069] E1
10.25 [.404] E2
C
D
4.39 [.173]
6
NOTICE TIAL. THIS PLOT AND THE INFORMATION IN ARE THE PROPRIETARY AND FORMATION OF CREE, INC. THIS PLOT IED, REPRODUCED OR DISCLOSED TO ANY ERSON WITHOUTTHE WRITTEN CONSENT
C
5
4
8.00 [.315] P 5.50 [.217]F
10.25 [.404] E2
1.50 [.059] 3 D1 12.00 [.472] NOMINAL
12.30 [.484] MAX WB 7.3°
3.78 [.149] Bo
REV
2
8.00 [.315] P
REVISONS
DESCRIPTION
.30 [.012] T
1.50 [.059] D1
1
BY DATE APP'D
4.39 [.173]
B
2.38
+.10 4.39 [.173] +.0039 .0937 -.00[ -.0000]
2.38
Ko
C
+.10 -.00[
.0937
+.0039 -.0000]
Ko
7.3°
B
POCKET SIZE
8.00 [.315] P 1.50 [.059] D1 3.78 [.149] Ao +.10 +.0039 2.38 .0937 User Feed Direction -.00[ -.0000] Ko
A
POCK
D
.30 [.012] T
3.78 Ao -
Bo Ko -
[.149] Ao
3.78mm [.149"] 3.78mm [.149"] 2.38mm [.094"]
DATE
Ao Bo Ko UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: 1.6
DRAWN BY
3.78m
3.78m
2.38m
DATE
4.39 [.173]
A
B
1.5± .1 8±.1
5
D. CRONIN
CHECK
05/02/11
DATE
7.3°
END
6
CATHODE SIDE
4
START
THIRD ANGLE PROJECTION
NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTANED WITHIN ARE THE PROPRIETARY AND 3.78 [.149] CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT 6 Ao MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC.
Ao 4
±.10 POCKET SIZE 3
6
4±.1 OTHERWISE SPECIFIED D. CRONIN B UNLESS DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. 2.5±.1 1.75
DRAWN BY CHECK
-APPROVED
-DATE
05/02/11
DATE
4600 Silicon Drive Durham, N.C 27703 Phone (919) 313-5300 Fax (919) 313-5558
TITLE
TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: 1.6
---
-DATE
THIRD ANGLE PROJECTION
-MATERIAL
--
T
APPROVED
A
--
MATERIAL
3.78mm [.149"] 12.0 3.78mm [.149"]
3
CARRIER TAPE XP HEW 2
SIZE
1
REV.
-FINAL PROTECTIVE FINISH
SI
FINAL PROTECTIVE FINISH
5
-INDEX
5
Bo Ko -
+.3 -.0
2.38mm [.094"]
DATE
12 2
--
QTY
SCALE
ITEM
C
DRAWING NO.
2402-00018 4
SHEET OF
ACOMMENTS
1 /1
2400-00009
-2
SC
D
3
1 2
DRAWING SCALE
2400-00009-CORE 2400-00009-REEL
C
1
ANODE SIDE
A
D
Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.)
6 5
Loaded Pockets (1000 Lamps)
UNLESS OTHERWISE SPECIFIED D. CRONIN Leader DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. 400mm (min.) of -TOLERANCE UNLESS SPECIFIED: .XX ± .25 empty pockets with -.XXX ± .125 X° ± .5 ° THIRD ANGLE PROJECTION at least 100mm FOR SHEET METAL PARTS ONLY .X sealed±±by1.5tape -.XX .75 .25 (50 empty .XXX ±± .5 ° min.) pockets X°
CHECK APPROVED MATERIAL
DRAWN BY
05/02/11
DATE
4600 Silicon Drive Durham, N.C 27703 Phone (919) 313-5300 Fax (919) 313-5558
TITLE
-DATE
A
--
CARRIER TAPE XP HEW
SIZE
D
FINAL PROTECTIVE FINISH
SURFACE FINISH: 1.6
--
C
DRAWING NO.
2402-00018
SHEET OF
REV.
A
1 /1
SCALE
DRAWING SCALE
4
3
2
1
User Feed Direction
B
Carrier Tape
C
12.4 +.2 .0 MEASURED AT HUB
C
Pocket Tape
330 +.25 -.75
7"
13mm
16.4 +0.2 .0 MEASURED AT HUB
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH:
1.6
DRAWN BY DATE
1.9±.4 21 ±.4
4600 Silicon Drive Durham, N.C 27703 Phone (919) 313-5300 Fax (919) 313-5558
TITLE
D. CRONIN
CHECK
11/29/10
DATE
-APPROVED
THIRD ANGLE PROJECTION
-MATERIAL
13.1 ±.2
DATE
---
A
XP HEW LOADING SPEC
SIZE
-FINAL PROTECTIVE FINISH
B
6 5 4 3
-2
C
3.000
DRAWING NO.
2402-00014
SHEET OF
REV.
A
1 /1
B
SCALE
12.4 +1.0 -.5 MEASURED AT EDGE
1
60°
60°
A
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks REV BY DATE APP'D DESCRIPTION Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. UNLESS OTHERWISE SPECIFIED
DRAWN BY DATE
REVISONS
THIRD ANGLE PROJECTION
DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .01 .XXX ± .005 X° ± .5 °
D. CRONIN --
09/29/09 --
CHECK
DATE
4600 Silicon Drive Durham, N.C 27703 Fax (919) 313-5558
Phone (919) 313-5300
13
APPROVED
DATE
-MATERIAL
--
TITLE
A
REEL, 13" X 12MM, 3 PIECE SNAP
Dessicant Desiccant x lamp xT-E lEDs (inside bag) (inside bag) Humidity Indicator Humidity Indicator Card (inside bag) (inside bag) PacKaGinG Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag
Label with Cree Bin CREE Bin Code & Barcode Label # Code, Qty, Lot Label with CREE Bin Code Cree Bin & Barcode Label Code, Qty, Lot # Labelwith CustomerBin Label with Cree P/N, Qty, Lot Lot # Code, Qty, #, PO # Label with Cree Bin Label with Customer P/N, Qty, Lot #, PO Code, Qty, Lot# #
Patent Label Patent Label Label with Customer Order Code, Qty, Reel ID, PO # Label with Customer Order Code, Qty, Reel ID, PO #
Label with Customer Order Code, Qty, Reel ID, PO#
Label with Cree Bin Code, Qty, Lot #
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright © 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc.
14
