LM6-PPG1-3B-N1

Cree® SMD LED Model # LM6-PPG-3B-N Data Sheet 120-degree, 3.3 x 3.5-mm, SMT LED in green color with water-transparent lens and black coated surface Applications • • • • Indoor and Outdoor Displays Backlighting Coupling into Light Guides RGB Full-Color Displays Absolute Maximum Ratings (TA = 25°C) Absolute Maximum Rating R Forward Current Note 1 Items Symbol IF Note 2 Unit mA mA V mW °C °C °C °C/W °C/W °C/W °C/W 3 x 40 3 x 100 5 3 x 160 -40 ~ +100 -40 ~ +100 110 400 580 280 430 Peak Forward Current Reverse Voltage Power Dissipation IFP VR PD Topr Tstg TJ Note 3 Operation Temperature Storage Temperature Junction Temperature Junction/ambient 1 chip on RTHJA RTHJA RTHJS RTHJS Junction/ambient 3 chips on Note 3 Junction/solder point 1 chip on Junction/solder point 3 chips on 1. 2. 3. Notes: Single-color light. Pulse width ≤0.1 msec, duty ≤1/10. RTH test condition: mounted on PC Board FR 4 (pad size ≥16 mm2) LD-CT178.000 Data Sheet: C Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Dominant Wavelength Viewing Angle at 50% Forward Voltage Luminous Intensity Reverse Current (max) Condition IF = 3 x 20 mA IF = 3 x 20 mA IF = 3 x 20 mA IF = 3 x 20 mA VR = 5 V Symbol λDOM 2θ½ VF IV IR 1120 Minimum 520 Typical 527 120 3.4 1600 10 4.0 Maximum 540 Unit nm deg V mcd μA Subject to change without notice. www.cree.com/ledlamps  Standard Bins for LM6-PPG-3B-N (IF = 3 x 20 mA) Lamps are sorted to luminous intensity (IV) and chromaticity coordinates (x,y) bins shown. Orders for LM6-PPG1-3B-N1 may be filled with any or all bins contained as below. All luminous intensity (IV) and chromaticity coordinates (x,y) values shown and specified are at IF = 3 x 20 mA. X7 X8 X9 X10 Y1 or above X2 Luminous Intensity (IV) 2800 mcd 2240 mcd X1 1800 mcd W2 1400 mcd W1 1120 mcd 520 nm 525 nm 530 nm 535 nm 540 nm Dominant Wavelength (WD) Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. Tolerance of measurement of luminous intensity is ±10%. 3. Tolerance of measurement of the dominant wavelength is ±1 nm. 4. Tolerance of measurement of VF is ±0.05 V. 5. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 6. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 7. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 2 CLD-CT78.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Graphs Graphs 100.0 80.0 60.0 40.0 20.0 0.0 3.0 3.4 3.6 3.8 4.0 3.2 FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE. Vf(V) If (mA) Vr(V) -50 -40 Document No. Rev. No. -30 -20 -10 0 0.0 -10.0 -20.0 -30.0 -40.0 Ir(uA) FIG.2 REVERSE CURRENT VS. REVERSE VOLTAGE. -50.0 SPE/LM6-PPG1-3B-N1 01 RELATIVE LUMINOUS INTENSITY 5.0 4.0 3.0 2.0 1.0 0.0 0.0 If(mA) 20.0 40.0 60.0 80.0 100.0 Half Power WL=38nm Domi WL= 527nm 100% 75% 50% 25% 0% 300 400 500 600 WL(nm) 700 FIG.3 RELATIVE LUMINOUS INTENSITY VS. FORWARD CURRENT FIG.4 RELATIVE LUMINOUS INTENSITY VS. WAVELENGTH. 50% Power Angle : 120¢X 0 100 80 60 40 20 0 IF(mA) Ie(%) 100% 80% 60% 40% 1 CHIP ON 3 CHIP ON 0 20 40 60 80 20% T ( C) 100 -90 -60 -30 0 30 60 90 0% FIG.5 MAXIMUM FORWARD DC CURRENT VS SOLDER POINT TEMPERATURE IF(mA) FIG.6 FAR FIELD PATTERN. 100 80 60 40 20 0 1 CHIP ON 3 CHIP ON 0 20 40 60 80 T ( C) 100 FIG.7 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE Items Prepared by Signatures WangFJ Date 2007-04-06 Rev.No Date Revision History Change Description Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Cree logo are registered trademarks of Cree, Inc. XieJH 2007-04-06 Checked by Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the 3 CLD-CT78.000 DavidLiu Approved by 2007-04-06 splays Mechanical Dimensions ides ys gs at Ta = 25°C Symbol IF IFP VR PD Topr Tstg Tj Rth JA Rth JA on on Rth JS Rth JS 3 Document No. Rev. No. Dimension Draw ing SPE/LM6-PPG1-3B-N1 01 All dimensions are in mm. Absolute maximum Rating 3X40 3X100 5 3X160 -40~+100 -40~+100 +110 400 580 280 430 Unit mA mA V mW °C °C °C °C/W °C/W °C/W °C/W y =16mm2) al Characteristics(Ta = 25°C) Symbol Condition Min. Typ. Max. Unit Notes 2½ dom IF=3X20mA 520 527 540 nm IF=3X20mA Deg. --120 --RoHS Compliance VF IF=3X20mA -3.4 4.0 V The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the Iv IF=3 X 20mA 1120 1600 -mcd threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment IR VR=5V --10 A (RoHS), as amended through --April 21, 2006. Vision Advisory Claim Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.  CLD-CT78.000 2/4 Format #: COTCO-D-074 REV.4 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color aaaaaaaaa-aaa-aa- x x x x x IV 1: Full-color distribution 2~9, A~Z . . . : special request * 0: Full luminous intensity distribution 1~9, A~Z . . . : special request * Packing type Product P/N 0: Standard = tape pack 1~9, A~Z . . . : special request * * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number LM6-PPG1-3B-N1-00001 Description SMD 120 Pure Green 527nm, FULL RANK, Tape & Reel * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 5 CLD-CT78.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps