LP377PPG1-60G-03

Cree® P4 LED Model # LP377PPG-60G-03 Data Sheet 60-degree, 7.6 x 7.6 LED lamp in pure-green color with water-transparent lens and stopper Applications • • • Advertising Signs Indicators Message Boards Absolute Maximum Ratings (TA = 25°C) Items Forward Current Peak Forward Current Reverse Voltage Power Dissipation Operation Temperature Storage Temperature Lead Soldering Temperature Note Symbol IF IFP VR PD Topr Tstg Tsol Absolute Maximum Rating 30 100 5 132 -40 ~ +95 -40 ~ +100 Unit mA mA V mW °C °C Max. 260°C for 3 sec. max. (3 mm from the base of the epoxy bulb) Note: Pulse width ≤0.1 msec, duty ≤1/10. Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Forward Voltage Reverse Current Dominant Wavelength Luminous Flux 50% Power Angle Symbol VF IR λD ΦV 2θ½ Condition IF = 30 mA VR = 5 V IF = 30 mA IF = 30 mA IF = 30 mA Unit V μA nm mlm deg 515 1500 527 2500 60 Minimum Typical 3.6 Maximum 4.4 100 535 LD-CT116.000 Data Sheet: C Subject to change without notice. www.cree.com/ledlamps  Standard Bins for LP377PPG-60G-03 (IF = 30 mA) Lamps are sorted to luminous flux (ΦV ), VF and dominant wavelength (λD) bins shown. Orders for LP377PPG1-60G-03 may be filled with any or all bins contained as below. All luminous flux (ΦV) , VF and dominant wavelength (λD) values shown and specified are at IF = 30 mA. X6 X7 X8 X9 J or above Luminous Flux (ΦV) H G F 520 nm 525 nm 530 nm 535 nm 515 nm Dominant Wavelength (λD) Rank Luminous Flux Rank Voltage V7 2.8-3.0 V F 1500-2400 mlm G 2000-3000 mlm H 2500-3600 mlm V8 3.0-3.2 V V9 3.2-3.4 V V10 3.4-3.6 V V11 3.6-3.8 V V12 3.8-4.0 V V13 4.0-4.2 V V14 4.2-4.4 V Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. No tolerance in the measurement of luminous flux. 3. Tolerance of measurement of dominant wavelength is ±1 nm. 4. Tolerance of measurement of VF is ±0.05 V. 5. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 6. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 7. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 2 CLD-CT6.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Document No. SPE/LP377PBL1-60G-03 Rev. No. 02 Graphs Graphs If (mA) -50 Vr(V) -40 -30 -20 -10 0 0.0 -10.0 -20.0 -30.0 -40.0 Vf(V) 3.4 3.8 4.2 4.6 5.0 REVERSE VOLTAGE. Ir(uA) FIG.2 REVERSE CURRENT VS. -50.0 100.0 80.0 60.0 40.0 20.0 0.0 3.0 FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE. 2.5 2.0 1.5 1.0 0.5 0.0 0.0 If(mA) 20.0 40.0 60.0 80.0 100.0 100% 75% 50% 25% Half Power WL=28nm Domi WL= 470nm 0% 300 400 500 600 WL(nm) 700 FIG.3 RELATIVE LUMINOUS FLUX VS. FORWARD CURRENT FIG.4 RELATIVE LUMINOUS FLUX VS. WAVELENGTH. 50 40 30 20 10 0 IF(mA) 50% Power Angle : 60 Ie(%) 0 100% 80% 60% 40% Ta( C) 0 20 40 60 80 100 120 -90 -60 -30 0 30 60 90 20% 0% FIG.5 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE (Tjmax=120 C) FIG.6 FAR FIELD PATTERN Items Prepared by Checked by Approved by FCN# Signatures LiuZM Aldosin David Date 2005-07-07 2005-07-07 2005-07-07 Rev. No 02 Date Revision History Change Description V 2005-07-07 Release. add B rank. FCN20050221 Data is subject to change without prior notice; please refer to COTCO Website for the latest version. Copyright@2002 Cotco International Ltd. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps 3 CLD-CT6.000 4/4 Format #: COTCO-D-074 REV.4 Mechanical Dimensions Document No. SPE/LP377PBL1-60G-03 Rev. No. 02 All dimensions are in mm. Tolerance is ±0.25 mm unless otherwise noted. An epoxy meniscus may extend about 1.5 mm down the leads. Burr around bottom of epoxy may be 0.5 mm max. Dimension Drawing maximum ting 0 0 Unit mA mA V 2 +100 +100 mW °C °C °C for 3 sec Max. Notes base of the epoxy bulb) RoHS Compliance The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the = 25 ) Tathreshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. s( °C ondition should be cautioned not to stareTyp. light of this LED ax. Min. M product. The bright light can damage the eye. Unit Users at the F= Vision Advisory Claim 30mA ----- 3.6 --- 4.4 100 V A Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps VR = 5V 4 Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT6.000 Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color aaaaaaaaa-aaa-aa- x x x x x IV 1: Full-color distribution 2~9, A~Z . . . : special request * 0: Full luminous intensity distribution 1~9, A~Z . . . : special request * Packing type Product P/N 0: Standard = tube pack 1~9, A~Z . . . : special request * * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number LP377PPG1-60G-03-00001 Description P4 60 Pure Green 527nm, FULL RANK, Tube Pack * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 5 CLD-CT6.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps