LP377THR1-40G

Cree® P4 LED Model # LP377THR-40G Data Sheet 40-degree, 7.6 x 7.6 mm LED lamp in red color with water-transparent lens and stopper Applications • • • • Advertising Signs Indicators Traffic Signals Automotive Lighting Absolute Maximum Ratings (TA = 25°C) Items Forward Current Note 2 Symbol IF Note 1 Absolute Maximum Rating 70 200 5 220 -40 ~ +100 -40 ~ +100 Unit mA mA V mW °C °C Peak Forward Current Reverse Voltage Power Dissipation IFP VR PD Topr Tstg Tsol Operation Temperature Storage Temperature Lead Soldering Temperature Max. 260°C for 3 sec. max. (3 mm from the base of the epoxy bulb) 1. 2. Notes: Pulse width ≤0.1 msec, duty ≤1/10. A heat sink is recommended if the device is operated at ambient temperatures higher than 25°C. Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Forward Voltage Reverse Current Dominant Wavelength Symbol VF IR λD ΦV 2θ½ Condition IF = 70 mA VR = 5 V IF = 70 mA IF = 70 mA IF = 70 mA Unit V μA nm mlm deg 620 2500 628 4000 40 Minimum Typical 2.6 Maximum 3.2 100 637 LD-CT129.000 Data Sheet: C Luminous Flux 50% Power Angle Subject to change without notice. www.cree.com/ledlamps  Standard Bins for LP377THR-40G (IF = 70 mA) Lamps are sorted to luminous flux (ΦV), VF and dominant wavelength (λD) bins shown. Orders for LP377THR1-40G may be filled with any or all bins contained as below. All luminous flux (ΦV), VF and dominant wavelength (λD) values shown and specified are at IF = 70 mA. M or above L K J H 620 nm Dominant Wavelength (λD) 637 nm Rank Luminous Flux Forward Voltage (VF) Rank Voltage V4 H 2500-3600 mlm J 3000-4200 mlm K 3500-4800 mlm L 4000-6100 mlm V5 2.4-2.6 V V6 2.6-2.8 V V7 2.8-3.0 V V8 3.0-3.2 V 2.2-2.4 V Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. No tolerance of measurement of luminous flux. 3. Tolerance of measurement of dominant wavelength is ±1 nm. 4. Tolerance of measurement of VF is ±0.05 V. 5. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 6. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 7. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 2 CLD-CT29.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Graphs Document No. SPE/LP377THR1-40G Rev. No. 13 Graphs 100.0 80.0 60.0 40.0 20.0 0.0 2.0 2.2 2.4 2.6 2.8 3.0 FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE. Vf(V) If (mA) -60 Vr(V) -50 -40 -30 -20 -10 0.0 -10.0 -20.0 -30.0 -40.0 -50.0 Ir(uA) FIG.2 REVERSE CURRENT VS. REVERSE VOLTAGE. 2.5 2.0 1.5 1.0 0.5 0.0 0.0 If(mA) 20.0 40.0 60.0 80.0 100.0 Half Power WL=23nm Domi WL= 628nm 100% 75% 50% 25% WL(nm) 0% 400 500 600 700 800 900 FIG.4 RELATIVE LUMINOUS FLUX VS. WAVELENGTH. FIG.3 RELATIVE LUMINOUS FLUX VS. FORWARD CURRENT. 100 80 60 40 20 0 IF(mA) 50% Power Angle : 40 Ie(%) 0 100% 80% 60% 40% Ta( C) 0 20 40 60 80 100 120 -90 -60 -30 0 30 60 90 20% 0% FIG.5 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE (Tjmax=120 C) FIG.6 FAR FIELD PATTERN Items Prepared by Checked by Approved by FCN# Signatures LiuZM Aldosin David Date 2006-12-20 2006-12-20 2006-12-20 Rev. No 11 12 13 Date Revision History Change Description V 23Sep04 Add ESD and Notes; Change FIG.1&3&5; Change & D Rank form. 13Oct04 2006-12-20 D(max) V from 635nm to 637nm. FCN20060418 add H rank. Data is subject to change without prior notice; please refer to COTCO Website for the latest version. Copyright@2002 Cotco International Ltd. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps 3 CLD-CT29.000 4/4 Format #: COTCO-D-074 REV.4 Mechanical Dimensions All dimensions are in mm. Tolerance is ±0.25 mm unless otherwise noted. Rev. No. 13 An epoxy meniscus may extend about 1.5 mm down the leads. Document No. SPE/LP377THR1-40G Dimen be 0.5 mm max. Burr around bottom of epoxy maysion Draw ing maximum ting 0 0 Unit mA mA V 0 +100 +100 mW °C °C °C forNotes Max. 5 sec base of the Compliance RoHS epoxy bulb) otherwise restricted materials in temperatures higher maximum concentration values (also he device is operated at ambient this product are below thethan 25 deg C. For long term referred to as the (RoHS), as amended through April 21, 2006. Vision Advisory Claim The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or tive are recommended. Please contact certain hazardous substances in electrical and nd 50mA2002/95/EC on the restriction of the use of COTCO sales representative for more electronic equipment threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Direc- = 2 should s ( TaUsers5°C) be cautioned not to stare at the light of this LED product. The bright light can damage the eye. ondition F Min. --- Typ. 2.6 Max. 3.2 Unit V Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps = 70mA 4 Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT29.000 Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color aaaaaaaaa-aaa-aa- x x x x x IV 1: Full-color distribution 2~9, A~Z . . . : special request * 0: Full luminous intensity distribution 1~9, A~Z . . . : special request * Packing type Product P/N 0: Standard = tube pack 1~9, A~Z . . . : special request * * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number LP377THR1-40G-00001 LP377THR1-40G-00011 Description P4 40 Red 628nm, FULL RANK, Tube Pack P4 40 Red 628nm, J or above, Tube Pack * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 5 CLD-CT29.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps