LP377TYL1-40G

Cree® P4 LED Model # LP377TYL-40G Data Sheet 40-degree, 7.6 x 7.6 mm LED lamp in amber color with water-transparent lens and stopper Applications • • • • Advertising Signs Indicators Traffic Signals Automotive Lighting Absolute Maximum Ratings (TA = 25°C) Items Forward Current Note 2 Symbol IF Note 1 Absolute Maximum Rating 70 200 5 220 -40 ~ +100 -40 ~ +100 Unit mA mA V mW °C °C Peak Forward Current Reverse Voltage Power Dissipation IFP VR PD Topr Tstg Tsol Operation Temperature Storage Temperature Lead Soldering Temperature Max. 260°C for 3 sec. max. (3 mm from the base of the epoxy bulb) 1. 2. Notes: Pulse width ≤0.1 msec, duty ≤1/10. A heat sink is recommended if the device is operated at ambient temperatures higher than 25°C. Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Forward Voltage Reverse Current Dominant Wavelength Symbol VF IR λD ΦV 2θ½ Condition IF = 70 mA VR = 5 V IF = 70 mA IF = 70 mA IF = 70 mA Unit V μA nm mlm deg 584 2000 591 3200 40 Minimum Typical 2.6 Maximum 3.2 100 599 LD-CT132.000 Data Sheet: C Luminous Flux 50% Power Angle Subject to change without notice. www.cree.com/ledlamps  Standard Bins for LP377TYL-40G (IF = 70 mA) Lamps are sorted to luminous flux (ΦV), VF and dominant wavelength (λD) bins shown. Orders for LP377TYL1-40G may be filled with any or all bins contained as below. All luminous flux (ΦV), VF and dominant wavelength (λD) values shown and specified are at IF = 70 mA. X2 X3 X4 X5 X6 L or above K J H G 584 nm 587 nm 590 nm 596 nm 593 nm 599 nm Dominant Wavelength (λD) Rank Luminous Flux Forward Voltage (VF) Rank Voltage V4 G 2000-3000 mlm H 2500-3600 J 3000-4200 mlm K 3500-4800 mlm V5 2.4-2.6 V V6 2.6-2.8 V V7 2.8-3.0 V V8 3.0-3.2 V 2.2-2.4 V Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. No tolerance of measurement of luminous flux. 3. Tolerance of measurement of dominant wavelength is ±1 nm. 4. Tolerance of measurement of VF is ±0.05 V. 5. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 6. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 7. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 2 CLD-CT32.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Model No. Doc. No. LP377TYL1-40G 12 23Sep04 Graphs Graphs If (mA) -60 Vr(V) -50 -40 -30 -20 -10 0.0 -10.0 -20.0 -30.0 -40.0 Vf(V) -50.0 Ir(uA) FIG.2 REVERSE CURRENT VS. REVERSE VOLTAGE. 100.0 80.0 60.0 40.0 20.0 0.0 2.0 2.2 2.4 2.6 2.8 3.0 FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE. 2.5 2.0 1.5 1.0 0.5 0.0 0.0 If(mA) 20.0 40.0 60.0 80.0 100.0 Half Power WL=20nm Domi WL= 591nm I (RELATIVE LUMINOUS FLUX) 100% 75% 50% 25% WL(nm) 500 600 700 800 900 FIG.4 RELATIVE LUMINOUS FLUX VS. WAVELENGTH. 0% 400 FIG.3 RELATIVE LUMINOUS FLUX VS. FORWARD CURRENT. 100 80 60 40 20 0 IF(mA) 50% Power Angle : 40 Ie(%) 0 100% 80% 60% 40% Ta( C) 0 20 40 60 80 100 120 -90 -60 -30 0 30 60 90 20% 0% FIG.5 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE (Tjmax=120 C) FIG.6 FAR FIELD PATTERN Items Prepared by Checked by Approved by ECN# Signatures LiuZM AldosinLi David Date 2004/09/23 2004/09/23 2004/09/23 DOC. No. J 16Jul03 K 11Nov03 12 23Sep04 Revision History CHANGE DESCRIPTION Cancel VF(min). add V8 & X6 PD from 150 to 220; Change FIG.5 Add ESD and Notes; Change FIG.1&3&5; Change V ECN-H20040261 & D Rank form. Data is subject to change without prior notice. Copyright@2002 Cotco International Ltd. Obsoletes Doc: K 11Nov03. 3 Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps CLD-CT32.000 4/4 COTCO-D-074 REV.1 Mechanical Dimensions Model No. LP377TYL1-40G Doc. No. 12 23Sep04 All dimensions are in mm. Tolerance is ±0.25 mm unless otherwise noted. An epoxy meniscus may extend about 1.5 mm down the leads. Burr around bottom of epoxy may be 0.5 mm max. Dimension Drawing maximum ting 0 0 Unit mA mA V 0 +100 +100 mW °C °C °C forNotes Max. 5 sec base of the epoxy bulb) RoHS Compliance threshold recommended. Please contact or are used in an exempted application, in accordance with EU Direcand 50mA are limits) permitted for such substances, COTCO sales representative for more tive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. Vision Advisory Claim The he devicelevelsperated at ambient this product are below thethan 25 deg C. For long term referred to asor is o of environmentally sensitive, persistent biologically toxic (PBT), persistent values (also temperatures higher maximum concentration organic pollutants (POP), the otherwise restricted materials in = 2 should s ( TaUsers 5°C) be cautioned not to stare at the light of this LED product. The bright light can damage the eye. ondition F Min. Typ. Max. Unit Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Copyright reserved. The to change and = 70mA © 2007 Cree, Inc. --rightsof Cree, Inc. information in this document is subject3.2 without notice. Cree V the -All 2.6 Cree logo are registered trademarks 4 CLD-CT32.000 Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color aaaaaaaaa-aaa-aa- x x x x x IV 1: Full-color distribution 2~9, A~Z . . . : special request * 0: Full luminous intensity distribution 1~9, A~Z . . . : special request * Packing type Product P/N 0: Standard = tube pack 1~9, A~Z . . . : special request * * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number LP377TYL1-40G-00001 LP377TYL1-40G-00011 Description P4 40 Amber 591nm, FULL RANK, Tube Pack P4 40 Amber 591nm, H or above, Tube Pack * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 5 CLD-CT32.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps