LP377TYL1-A0G

Cree® P4 LED Model # LP377TYL-A0G Data Sheet 100-degree, 7.6 x 7.6 mm LED lamp in amber color with water-transparent lens and stopper Applications • • • Advertising Signs Indicators Automotive Lighting Absolute Maximum Ratings (TA = 25°C) Items Forward Current Note 2 Symbol IF Note 1 Absolute Maximum Rating 70 200 5 220 -40 ~ +100 -40 ~ +100 Unit mA mA V mW °C °C Peak Forward Current Reverse Voltage Power Dissipation IFP VR PD Topr Tstg Tsol Operation Temperature Storage Temperature Lead Soldering Temperature Max. 260°C for 3 sec. max. (3 mm from the base of the epoxy bulb) 1. 2. Notes: Pulse width ≤0.1 msec, duty ≤1/10. A heat sink is recommended if the device is operated at ambient temperatures higher than 25°C. Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Forward Voltage Reverse Current Dominant Wavelength Luminous Flux Symbol VF IR λD ΦV 2θ½ Condition IF = 70 mA VR = 5 V IF = 70 mA IF = 70 mA IF = 70 mA Unit V μA nm mlm deg 584 2000 591 3200 100 Minimum Typical 2.6 Maximum 3.2 100 599 LD-CT134.000 Data Sheet: C 50% Power Angle Subject to change without notice. www.cree.com/ledlamps  Standard Bins for LP377TYL-A0G (IF = 70 mA) Lamps are sorted to luminous flux (ΦV), VF and dominant wavelength (λD) bins shown. Orders for LP377TYL1-A0G may be filled with any or all bins contained as below. All luminous flux (ΦV), VF and dominant wavelength (λD) values shown and specified are at IF = 70 mA. X2 X3 X4 X5 X6 L or above K J H G 584 nm 587 nm 590 nm 596 nm 593 nm 599 nm Dominant Wavelength (λD) Rank Luminous Flux Forward Voltage (VF) Rank Voltage V4 G 2000-3000 mlm H 2500-3600 mlm J 3000-4200 mlm K 3500-4800 mlm V5 2.4-2.6 V V6 2.6-2.8 V V7 2.8-3.0 V V8 3.0-3.2 V 2.2-2.4 V Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. No tolerance of measurement of luminous flux. 3. Tolerance of measurement of dominant wavelength is ±1 nm. 4. Tolerance of measurement of VF is ±0.05 V. 5. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 6. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 7. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 2 CLD-CT34.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Model No. Doc. No. LP377TYL1-A0G 10 23Sep04 Graphs Graphs 100.0 80.0 60.0 40.0 20.0 If (mA) -60 Vr(V) -50 -40 -30 -20 -10 0.0 -10.0 -20.0 -30.0 -40.0 0.0 2.0 Vf(V) 2.2 2.4 2.6 2.8 3.0 FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE. -50.0 Ir(uA) FIG.2 REVERSE CURRENT VS. REVERSE VOLTAGE. 2.5 2.0 1.5 1.0 0.5 0.0 0.0 If(mA) 20.0 40.0 60.0 80.0 100.0 Half Power WL=20nm Domi WL= 591nm I (RELATIVE LUMINOUS FLUX) 100% 75% 50% 25% WL(nm) 500 600 700 800 900 FIG.4 RELATIVE LUMINOUS FLUX VS. WAVELENGTH. 0% 400 FIG.3 RELATIVE LUMINOUS FLUX VS. FORWARD CURRENT. 100 80 60 40 20 0 IF(mA) 50% Power Angle : 100 Ie(%) 0 100% 80% 60% 40% Ta( C) 0 20 40 60 80 100 120 -90 -60 -30 0 30 60 90 20% 0% FIG.5 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE (Tjmax=120 C) FIG.6 FAR FIELD PATTERN Items Prepared by Checked by Approved by ECN# Signatures LiuZM AldosinLi David Date 2004/09/23 2004/09/23 2004/09/23 DOC. No. H 16Jul03 I 11Nov03 10 23Sep04 Revision History CHANGE DESCRIPTION Cancel VF(min). add V8 & X6 PD from 150 to 220; Change FIG.5 Add ESD and Notes; Change FIG.1&3&5; Change V ECN-H20040261 & D Rank form. Data is subject to change without prior notice. Copyright@2002 Cotco International Ltd. Obsoletes Doc: I 11Nov03. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps 4/4 COTCO-D-074 REV.1 3 CLD-CT34.000 Mechanical Dimensions Model No. LP377TYL1-A0G Doc. No. 10 23Sep04 All dimensions are in mm. Tolerance is ±0.25 mm unless otherwise noted. An epoxy meniscus may extend about 1.5 mm down the leads. Burr around bottom of epoxy may be 0.5 mm max. Dimension Drawing aximum ng Unit mA 0 mA V 0 +100 +100 mW °C °C C for NotesMax. 5 sec base of the epoxy bulb) RoHS Compliance threshold limits) permitted or are accordance with EU Direc nd 50mA are recommended.for such substances, certain used in an exempted application, inand electronic equipment Please contact COTCO sales representative for more tive 2002/95/EC on the restriction of the use of hazardous substances in electrical (RoHS), as amended through April 21, 2006. Vision Advisory Claim e device is operated atmaterials in temperatures below the maximum concentration values (also referred to as the otherwise restricted ambient this product are higher than 25 deg C. For long term The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or = 25should ( Ta Users °C) be cautioned not to stare at the light of this LED product. The bright light can damage the eye. ondition Cree = 70mAlogo Min. --- Typ. 2.6 Max. 3.2 Unit V Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the are registered trademarks of Cree, Inc. 4 CLD-CT34.000 Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color aaaaaaaaa-aaa-aa- x x x x x IV 1: Full-color distribution 2~9, A~Z . . . : special request * 0: Full luminous intensity distribution 1~9, A~Z . . . : special request * Packing type Product P/N 0: Standard = tube pack 1~9, A~Z . . . : special request * * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number LP377TYL1-A0G-00001 LP377TYL1-A0G-00011 Description P4 100 Amber 591nm, FULL RANK, Tube Pack P4 100 Amber 591nm, H or above, Tube Pack * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 5 CLD-CT34.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps