LP379THR1-C0G

Cree® P4 LED Model # LP379THR-C0G Data Sheet 120-degree, 7.6 x 7.6 mm LED lamp in high-red color with water-transparent lens and stopper Applications • • • Advertising Signs Indicators Automotive Lighting Absolute Maximum Ratings (TA = 25°C) Items Forward Current Note 2 Symbol IF Note 1 Absolute Maximum Rating 70 200 5 220 -40 ~ +100 -40 ~ +100 Unit mA mA V mW °C °C Peak Forward Current Reverse Voltage Power Dissipation IFP VR PD Topr Tstg Tsol Operation Temperature Storage Temperature Lead Soldering Temperature Max. 260°C for 3 sec. max. (3 mm from the base of the epoxy bulb) 1. 2. Notes: Pulse width ≤0.1 msec, duty ≤1/10. A heat sink is recommended if the device is operated at ambient temperatures higher than 25°C. Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Forward Voltage Reverse Current Dominant Wavelength Luminous Flux Symbol VF IR λD ΦV 2θ½ Condition IF = 70 mA VR = 5 V IF = 70 mA IF = 70 mA IF = 70 mA Unit V μA nm mlm deg 620 3000 628 4000 120 Minimum Typical 2.6 Maximum 3.2 100 637 LD-CT135.000 Data Sheet: C 50% Power Angle Subject to change without notice. www.cree.com/ledlamps  Standard Bins for LP379THR-C0G (IF = 70 mA) Lamps are sorted to luminous flux (ΦV), VF and dominant wavelength (λD) bins shown. Orders for LP379THR1-C0G may be filled with any or all bins contained as below. All luminous flux (ΦV), VF and dominant wavelength (λD) values shown and specified are at IF = 70 mA. M or above L K J 620 nm Dominant Wavelength (λD) 637 nm Rank Luminous Flux Forward Voltage (VF) Rank Voltage V4 2.2-2.4 V J 3000-4200 mlm K 3500-4800 mlm L 4000-6100 mlm V5 2.4-2.6 V V6 2.6-2.8 V V7 2.8-3.0 V V8 3.0-3.2 V Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. No tolerance of measurement of luminous flux. 3. Tolerance of measurement of dominant wavelength is ±1 nm. 4. Tolerance of measurement of VF is ±0.05 V. 5. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 6. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 7. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 2 CLD-CT35.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Model No. Doc. No. LP379THR1-C0G 06 13Oct04 Graphs Graphs 100.0 80.0 60.0 40.0 20.0 If (mA) -60 Vr(V) -50 -40 -30 -20 -10 0.0 -10.0 -20.0 -30.0 -40.0 0.0 2.0 2.2 2.4 2.6 2.8 3.0 FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE. Vf(V) -50.0 Ir(uA) FIG.2 REVERSE CURRENT VS. REVERSE VOLTAGE. 2.5 2.0 1.5 1.0 0.5 0.0 0.0 If(mA) 20.0 40.0 60.0 80.0 100.0 Half Power WL=23nm Domi WL= 628nm I (RELATIVE LUMINOUS FLUX) 100% 75% 50% 25% WL(nm) 500 600 700 800 900 FIG.4 RELATIVE LUMINOUS FLUX VS. WAVELENGTH. 0% 400 FIG.3 RELATIVE LUMINOUS FLUX VS. FORWARD CURRENT. 100 80 60 40 20 0 IF(mA) 50% Power Angle : 120 Ie(%) 0 100% 80% 60% 40% Ta( C) 0 20 40 60 80 100 120 -90 -60 -30 0 30 60 90 20% 0% FIG.5 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE (Tjmax=120 C) FIG.6 FAR FIELD PATTERN Items Prepared by Checked by Approved by ECN# Signatures LiuZM AldosinLi David Date 2004/10/13 2004/10/13 2004/10/13 DOC. No. D 08Oct03 05 23Sep04 06 13Oct04 Revision History CHANGE DESCRIPTION PD from 150mW to 220mW. Change FIG.5 Add ESD and Notes; Change FIG.1&3&5; Change D(max) V & D Rank form. ECN-H20040276 from 635nm to 637nm. Data is subject to change without prior notice. Copyright@2002 Cotco International Ltd. Obsoletes Doc: 05 23Sep04. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps 3 CLD-CT35.000 4/4 COTCO-D-074 REV.1 Mechanical Dimensions All dimensions are in mm. Tolerance is ±0.25 mm unless otherwise noted. An epoxy meniscus may extend about 1.5 mm down the leads. Burr around bottom of epoxy maysion Dramax. g Dimen be 0.5 mm win Model No. Doc. No. LP379THR1-C0G 06 13Oct04 maximum ting 0 0 Unit mA mA V 0 +100 +100 mW °C °C °C forNotes Max. 5 sec base of theCompliance RoHS epoxy bulb) The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the he device is operated at ambient temperatures higher than 25 deg C. For long in rm threshold limits) permitted for such substances, or are used in an exempted application, teaccordance with EU Directive and 50mA2002/95/EC on the restriction of the use of certain hazardous representative for moreelectronic equipment are recommended. Please contact COTCO sales substances in electrical and (RoHS), as amended through April 21, 2006. Vision Advisory Claim s ( Ta = 25°C) ondition F Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye. Min. --- Typ. 2.6 Max. 3.2 Unit V Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps = 70mA 4 Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT35.000 Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color aaaaaaaaa-aaa-aa- x x x x x IV 1: Full-color distribution 2~9, A~Z . . . : special request * 0: Full luminous intensity distribution 1~9, A~Z . . . : special request * Packing type Product P/N 0: Standard = tube pack 1~9, A~Z . . . : special request * * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number LP379THR1-C0G-00001 LP379THR1-C0G-00011 Description P4 120 High Red 628nm, FULL RANK, Tube Pack P4 120 High Red 628nm, K or above, Tube Pack * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 5 CLD-CT35.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps