LP476THR1-90G-01

Cree® P4 LED Model # LP476THR-90G-0 Data Sheet 90-degree, 7.6 x 7.6 mm LED lamp in red color with water-transparent lens and stopper Applications • • • Advertising Signs Indicators Automotive Lighting Absolute Maximum Ratings (TA = 25°C) Items Forward Current Note 2 Symbol IF Note 1 Absolute Maximum Rating 70 200 5 220 -40 ~ +100 -40 ~ +100 Unit mA mA V mW °C °C Peak Forward Current Reverse Voltage Power Dissipation IFP VR PD Topr Tstg Tsol Operation Temperature Storage Temperature Lead Soldering Temperature Max. 260°C for 3 sec. max. (3 mm from the base of the epoxy bulb) 1. 2. Notes: Pulse width ≤0.1 msec, duty ≤1/10. A heat sink is recommended if the device is operated at ambient temperatures higher than 25°C. Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Forward Voltage Reverse Current Dominant Wavelength Luminous Flux Symbol VF IR λD ΦV 2θ½H-H 2θ½V-V Condition IF = 70 mA VR = 5 V IF = 70 mA IF = 70 mA IF = 70 mA IF = 70 mA Unit V μA nm mlm deg deg 620 1520 628 3000 90 35 Minimum Typical 2.6 Maximum 3.2 100 637 LD-CT137.000 Data Sheet: C 50% Power Angle Subject to change without notice. www.cree.com/ledlamps  Standard Bins for LP476THR-90G-0 (IF = 70 mA) Lamps are sorted to luminous intensity (IV), VF and dominant wavelength (λD) bins shown. Orders for LP476THR1-90G-01 may be filled with any or all bins contained as below. All luminous intensity (IV), VF and dominant wavelength (λD) values shown and specified are at IF = 70 mA. 5860 mcd Luminous Intensity (IV) Y or above X 4180 mcd W 3000 mcd V 2130 mcd U 1520 mcd 620 nm 637 nm Dominant Wavelength (λD) Forward Voltage (VF) Rank Voltage V4 2.2-2.4 V V5 2.4-2.6 V V6 2.6-2.8 V V7 2.8-3.0 V V8 3.0-3.2 V Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. Tolerance of measurement of luminous intensity is ±15%. 3. Tolerance of measurement of dominant wavelength is ±1 nm. 4. Tolerance of measurement of VF is ±0.05 V. 5. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 6. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 7. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 2 CLD-CT37.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Document No. SPE/LP476THR1-90G-01 Rev. No. 02 Graphs Graphs -60 Vr(V) -50 -40 -30 -20 -10 0.0 -10.0 -20.0 -30.0 -40.0 Vf(V) 100.0 80.0 60.0 40.0 20.0 If (mA) 0.0 2.0 2.2 2.4 2.6 2.8 3.0 FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE. Ir(uA) -50.0 FIG.2 REVERSE CURRENT VS. REVERSE VOLTAGE. 2.5 2.0 1.5 1.0 0.5 0.0 0.0 If(mA) 20.0 40.0 60.0 80.0 100.0 Half Power WL=23nm Domi WL= 628nm I (RELATIVE LUMINOUS INTENSITY) 100% 75% 50% 25% WL(nm) 0% 400 500 600 700 800 900 FIG.4 RELATIVE LUMINOUS INTENSITY VS. WAVELENGTH. FIG.3 RELATIVE LUMINOUS INTENSITY VS. FORWARD CURRENT. 50% Power Angle : 100 80 60 40 20 0 Ta( C) 0 20 40 60 80 100 120 -90 -60 -30 0 30 IF(mA) H-H : 90 V-V : 35 Ie(%) 100% H-H V-V 0 80% 60% 40% 20% 60 90 0% FIG.5 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE (Tjmax=120 C) FIG.6 FAR FIELD PATTERN Items Prepared by Checked by Approved by FCN# Signatures LiuZM Aldosin David Date 2005-05-18 2005-05-18 2005-05-18 Rev. No 02 Date Revision History Change Description 2005-05-18 Release. Change D(max)635 to 637nm; IV from V,,W,X,Y(typ)4000 to U,V,W,X(typ)4000mcd. FCN20050163 Data is subject to change without prior notice; please refer to COTCO Website for the latest version. Copyright@2002 Cotco International Ltd. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps 3 CLD-CT37.000 4/4 Format #: COTCO-D-074 REV.4 Mechanical Dimensions All dimensions are in mm. Tolerance is ±0.25No. unless otherwise noted. Rev. mm 02 An epoxy meniscus may extend about 1.5 mm down the leads. Document No. SPE/LP476THR1-90G-01 Dimenbe 0.5 Dr max. Burr around bottom of epoxy may sion mmaw ing maximum ting 0 00 5 20 +100 +100 Unit mA mA V mW °C °C Notes °C for 5 sec Max. e base RoHS Compliance of the epoxy bulb) otherwise restricted materials in temperatures higher maximum concentration values rm the device is operated at ambientthis product are below the than 25 deg C. For long te(also referred to as the (RoHS), as amended through April 21, 2006. Vision Advisory Claim Users 5°C) s ( Ta = 2should be cautioned not to stare at the light of this LED product. The bright light can damage the eye. The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or tive 2002/95/EC on the restriction of the use of COTCO sales representative for more and 50mA are recommended. Please contactcertain hazardous substances in electrical and electronic equipment threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Direc- Condition Cree logo IF = 70mA Min. --- Typ. 2.6 Max. 3.2 Unit V Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the are registered trademarks of Cree, Inc. 4 CLD-CT37.000 Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color aaaaaaaaa-aaa-aa- x x x x x IV 1: Full-color distribution 2~9, A~Z . . . : special request * 0: Full luminous intensity distribution 1~9, A~Z . . . : special request * Packing type Product P/N 0: Standard = tube pack 1~9, A~Z . . . : special request * * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number LP476THR1-90G-01-00001 LP476THR1-90G-01-00011 Description P4 90 High Red 628nm, FULL RANK, Tube Pack P4 90 High Red 628nm, V or above, Tube Pack * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 5 CLD-CT37.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps