Cree® SMD LED
Model # LP6-PPP2-0-N Data Sheet
120-degree, 6.0 x 5.0-mm, SMT LED in full color with white diffused lens
Applications
• • • • Indoor and Outdoor Displays Backlighting Camera Flash RGB Full-Color Displays
Absolute Maximum Ratings (TA = 25°C)
Absolute Maximum Rating R 80 200 5 200 G 80 100 5 410 -40 ~ +100 -40 ~ +100 110 250 500 150 150 110 210 300 130 160 110 210 300 130 160 B 80 100 5 410
Items Forward Current
Note 1
Symbol IF
Note 2
Unit mA mA V mW °C °C °C °C/W °C/W °C/W °C/W
Peak Forward Current Reverse Voltage Power Dissipation
IFP VR PD Topr Tstg TJ
Note 3
Operation Temperature Storage Temperature Junction Temperature Junction/ambient 1 chip on
RTHJA RTHJA RTHJS RTHJS
Junction/ambient 3 chips on
Note 3
Junction/solder point 1 chip on Junction/solder point 3 chips on
Notes:
1. 2. 3.
Single-color light. Pulse width ≤0.1 msec, duty ≤1/10. RTH test condition: mounted on PC Board FR 4 (pad size ≥40 mm2)
Typical Electrical & Optical Characteristics (TA = 25°C)
Characteristics Condition IF = 50 mA IF = 50 mA IF = 50 mA IF = 50 mA IF = 50 mA IF = 50 mA VR = 5 V Symbol λPEAK λDOM Δλ 2θ½ VF(avg) VF(max) IV(min) IV(avg) IR Values R 620 610~625 24 120 2.0 2.5 450 710 10 G 521 514~534 38 120 4.0 5.1 710 1000 10 B 468 460~480 28 120 4.0 5.1 280 450 10 Unit nm nm nm deg V V mcd mcd μA
LD-CT181.000 Data Sheet: C
Wavelength at peak emission Dominant Wavelength Spectral bandwidth at 50% IREL max Viewing Angle at 50% IV Forward Voltage
Luminous Intensity Reverse Current (max)
Subject to change without notice. www.cree.com/ledlamps
Standard Bins for LP6-PPP2-0-N (IF = 50 mA)
Lamps are sorted to luminous intensity (IV) and dominant wavelength (λD) bins shown. Orders for LP6-PPP2-01-N1 may be filled with any or all bins contained as below. All luminous intensity (IV) and dominant wavelength (λD) values shown and specified are at IF = 50 mA.
Luminous Intensity (IV)
1800 mcd 1120 mcd
X or above W V
710 mcd U 450 mcd 610 nm Dominant Wavelength (λD) 625 nm
Luminous Intensity (IV)
1800 mcd 1120 mcd
X or above W V
710 mcd 514 nm Dominant Wavelength (λD) 534 nm
Luminous Intensity (IV)
710 mcd 450 mcd
V or above U T
280 mcd 460 nm Dominant Wavelength (λD) 480 nm
Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. Tolerance of measurement of luminous intensity is ±10%. 3. Tolerance of measurement of the dominant wavelength is ±1 nm. 4. Tolerance of measurement of VF is ±0.05 V. 5. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 6. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 7. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely.
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
2
CLD-CT8.000
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps
Graphs
Graphs
Document No. SPE/LP6-PPP2-01-N1 Rev. No. 02
100.0 80.0 60.0 40.0 20.0
If (mA)
100.0
GREEN
If (mA)
80.0 60.0
BLUE
40.0 20.0
Vf(V) 5.0
RED
0.0 3.0
3.4
3.8
4.2
4.6
0.0
Vf(V) 1.6 1.8 2.0 2.2 2.4 2.6
F ORWARD CURRENT VS. FORWARD VOLTAGE.
FIG.1 FORWARD CURRENT VS. F ORWARD VOLTAGE.
4/6
Format #: COTCO-D-074
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
CLD-CT8.000
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps
REV.4
Graphs
Graphs
Document No. SPE/LP6-PPP2-01-N1 Rev. No. 02
5/6
Format #: COTCO-D-074
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
CLD-CT8.000
Cree, Inc. REV.4 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps
Document No. SPE/LP6-PPP2-01-N1 Rev. No. 02
Graphs
CIE Graph
the color coordinates of the mixed light can be expected within the area of the color triangle marked a). The color coordinates of the mixed light can be expected within the area of the color triangle marked “a)”. the achromatic (x=0.33, y=0.33) is marked “+”. The achromatic point point (x=0.33,y=0.33) is marked“+”
Items Prepared by Checked by Approved by FCN#
Signatures
WangFJ XieJH DavidLiu
Date
2007-04-05 2007-04-05 2007-04-05 Rev.No 02 Date 2007-04-05 Release
Revision History
Change Description
FCN20070101
Data is subject to change without prior notice; Please refer to COTCO Website for the latest version. Copyright@2002 Cotco International Ltd.
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps
5
CLD-CT8.000
6/6
Format #: COTCO-D-074
REV.4
displays
Mechanical Dimensions
Document No. SPE/LP6-PPP2-01-N1 Rev. No. 02 Dimension Draw ing
All dimensions are in mm.
ays tings at Ta = 25°C
Symbol IF IFP VR PD Topr Tstg Tj n* n*
3 3
Absolute maximum Rating
R
80 200 5 200
G
80 100 5 410 -40 ~ + 100 -40 ~ + 100
B
80 100 5 410
Unit mA mA V mW
°C °C
110 210 300 130 160
110 250 500 150 150
110 210 300 130 160
3
°C °C/W °C/W °C/W °C/W
Rth JA Rth JA Rth JS Rth JS
on on
width
很抱歉,暂时无法提供与“LP6-PPP2-01-N1”相匹配的价格&库存,您可以联系我们找货
免费人工找货