6351

DC Output Buffered Modul es • Compatible wi th 5 & 15 Volt Logic Systems • Buffered Inverting and Non-Inverting Mo dules INPUT SPECIFICATIONS Buffered output modules contain additional internal amplification to reduce drive requirements to a level suitable for the MOS devices used in many microprocessor systems. To further reduce the need for additional interface components, they are available with both inverting and non-inverting inputs, for 5 volt or 15 volt logic. 6311 6321 6341 6351 5 5 15 15 Non-Inverting Inverting Non-Inverting Inverting Must Turn On Voltage Range @ pin 4 [Vdc] 0.0 - 0.8 2.4 - 6.0 0.0 - 2.0 8.0 - 18 Must Turn Off Voltage Range @ pin 4 [Vdc] 2.4 - 6.0 0.0 - 0.8 8.0 - 18 0.0 - 2.0 Max. Input On-Current (Sink) @ pin 4 [µA] 75 @ 0.8V Ñ 175 @ 2.0V Ñ 100 @ 0.0V Ñ 250 @ 0.0V Ñ Ñ 75 @ 2.4V Ñ 75 @ 8.0V Ñ 250 @ 6.0V Ñ 200 @ 18V 10 10 10 10 10 10 10 10 3.5 - 6.0 3.5 - 6.0 10 -18 10 -18 Max. Logic Supply Current (w/o LED) @ 5Vdc [mA] ➀ 20 20 25 25 Max. Logic Supply Current (w/ LED) @ 5Vdc [mA] ➀ 15 15 22 22 0.02 - 3.5 0.02 - 3.5 0.02 - 3.5 0.02 - 3.5 3.0 - 60 3.0 - 60 3.0 - 60 3.0 - 60 Max. Surge Current [A] 5.0 5.0 5.0 5.0 Max. On-State Voltage [Vdc] 1.5 1.5 1.5 1.5 Max. Off-State Leakage [mA] 1.0 1.0 1.0 1.0 Max. Turn On Time [µS] 100 100 100 100 Max. Turn Off Time [µS] 100 100 100 100 60 60 60 (All voltages referenced to pin 5) Nominal Input Voltage [Vdc] Output Module Type Max. Input On-Current (Source) @ pin 4 [µA] Max. Input Current For Output (Sink) Off-State @ pin 4 [µA] ➁ (Source) Logic Supply Voltage Range [Vdc] OUTPUT SPECIFICATIONS Load Current Range @ 45û C [A] Load Voltage Range [Vdc] Transient Overvoltage [Vdc] GENERAL NOTES 60 © 2002 CRYDOM CORP Specifications subject to change without notice. ➀ LED optional. Placed in series with pin 3 for status indication. ➁ Max. allowable leakage current from driver maintain output off-state. ➂ Inductive loads must be diode suppressed. FastFax Document No. 309 Rev. 031902 PAGE 1 OF 2 For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540 Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154 Email: sales@crydom.com WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: intsales@crydom.com. GERMANY: +49 (0)180 3000 506 DC Output Buffered M odules GENERAL SPECIFICATIONS Min. Dielectric Input/Output (1 minute) 4,000 VRMS Min. Isolation Resistance Input/Output (@ 500V) 1010 Ohms 8 pF Capacitance input to output Temperature Range Ñ Operating -40û C to 80˚C Temperature Range Ñ Storage -40û C to 125˚C C U R R E N T D E R AT I N G C U RV E W IRING & M ECHANICAL DIAGRAM S LOAD CURRENT (AMPS) 3.5 1 (+) 3.0 2.5 ➂ ① 3 DC LOGIC SUPPLY DC LOGIC INPUT (+) INV or Non-INV Logic 4 LOAD DC Output Drive Circuit (-) 2.0 2 5 1.5 COM (-) 1.0 0 20 40 60 BOTTOM VIEW 80 AMBIENT TEMPERATURE (˚C) .30 (7.6) Max. Load Current vs. Temp. CAPTIVE #4-40. PHILLIPS HEAD HOLD DOWN SCREW BUFFERED OUTPUT M ODULES A buffered non-inverting module turns on when pin 4 is held in the low state (logic 0), the same as standard modules driven in the sink mode. A buffered inverting module conversely turns on when pin 4 is held high (logic 1). In the absence of an input signal and/or logic supply (open Circuit), all models will be in the off-state. Buffered modules may be used with standard 5 pin PB or MS mounting boards. However, the 3.3K pull-up resistor will add to the logic drive current of a non-inverting module and may be removed. For an inverting module, the resistor must be removed to avoid a false ÒonÓ command, unless a Ònor mally closedÓ condition is desirable for use with a ground seeking (logic 0) signal source. 1.70 (43.1) .60 (15.2) .100 (2.5) 1.00 (25.4) 1.25 (31.7) .25 (6.3) 5 4 3 2 1 .30 (7.6) .040 (1.0) DIA. (5 PLACES) .70 (17.8) 1.20 (30.5) 1.40 (35.5) 1.60 (40.6) All dimensions are in inches (millimeters) © 2002 CRYDOM CORP Specifications subject to change without notice. FastFax Document No. 309 Rev. 031902 PAGE 2 OF 2 For recommended applications and more information contact: USA: Sales Support (877) 502-5500 Tech Support (877) 702-7700 FAX (619) 710-8540 Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154 Email: sales@crydom.com WEB SITE: http://www.crydom.com UK: +44 (0)1202 365070 • FAX +44 (0)1202 365090 Crydom International Ltd., 7 Cobham Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: intsales@crydom.com. GERMANY: +49 (0)180 3000 506