PB32HQ

PB32HQ MOUNTING BOARD • Plug-compatible logic connections • Screw terminal barrier block for load connections • 5 amp field-replaceable fuses (LITTLEFUSE #251005 or equivalent) • Input and output modules accepted interchangeably • Operate with 5, 15 or 24 volt logic supplies • Captive-screw retaining system for Quad-Pack modules • All even-numbered logic connections are logic ground MECHANICAL SPECIFICATIONS DIMENSIONS: INCHES (MILLIMETERS) TOLERANCE: ±0.020 (±0.50) SWAGED STANDOFF THRU HOLE 0.15 (3.8) DIA. x 0.75 (19,1) LONG (4) 11.5 (291,9) 11.0 (279,4) 5.5 (139,7) 0.25 (6,4) 1 2 TB1 0.25 (6,4) PWR ON 5A SPARE FUSE D2 R1 D1 GND +5V C C 3 4 5 6 C C 7 8 9 10 C C 11 13 12 14 C C 15 17 16 18 C C 19 21 20 22 C C 23 24 25 26 C C 27 28 29 30 C C 31 32 TB3 F1A POWER BARRIER STRIPS (SEE NOTE 2,3) 6.5 (164,9) 6.0 (152,4) 4-40 SCREW TERMINAL LOGIC SUPPLY BARRIER STRIP REPLACEABLE 2 AMP LOGIC SUPPLY FUSE (SEE NOTE 4) J1 J2 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 REPLACEABLE 5 AMP LINE FUSES (16) (SEE NOTE 5) GORDOS QUAD-PACK DIGITAL I/O MODULES SOLD SEPERATELY 0-3 4-7 8-11 12-15 16-19 20-23 24-27 28-31 J3 57-462 PB-32HQ 3.15 (80,0) 3.9 (100,2) 50 CONDUCTOR MALE PIN CONNECTORS (J1,J2) (SEE NOTE 1) PAM-4 MULTIPLEXER BOARD SOLD SEPERATELY HEADER CONNECTOR (J3) CARD SUPPORTS (2) NOTES: 1) CONNECTOR IS CIRCUIT ASSEMBLY CA-50H-2B-SR OR EQUIVALENT. CONNECTORS ARE WIRED IN PARALLEL. 2) 6-32 SCREW TERMINAL BARRIER STRIPS ACCEPT WIRE SIZES FROM 24 TO 12 AWG. 3) OPTIONAL JUMPERS AVAILABLE TO INTERCONNECT BARRIER STRIP COMMONS. ORDER 2 EACH JUMPERS "JQ2" AND 4 EACH JUMPERS "JQ4". 4) LITTLE FUSE 251001 OR EQUIVALENT. 5) LITTLE FUSE 251005 OR EQUIVALENT. 1 C 3 5 C 7 9 C 11 13 C 15 17 C 19 21 C 23 25 C 27 29 C 31 LOWER BARRIER STRIP 32 LOGIC SUPPLY BARRIER STRIP 1 AMP LOGIC SUPPLY FUSE +5V GND 2 C 4 6 C 8 10 C 12 14 C 16 18 C 20 22 C 24 26 C 28 30 C UPPER BARRIER STRIP 5 AMP LINE FUSES (16) 1 2 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PWR ON 3 4 5 6 7 I/O MODULE PIN SOCKETS 70-PIN MALE CONNECTOR ACCEPTS PAM4 MULTIPLEXER BOARD J1 J2 SIGNAL INPUT/OUTPUT 50 CONDUCTOR MALE PIN CONNECTORS. J1 AND J2 ARE WIRED IN PARALLEL. Rev. 070808 DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / PERIGO HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. • Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION • Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil • Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. • Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen • Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSI ONE. • Spenga tutta l'alimentazion e che fornisce questa apparecchiatu ra prima del lavorare a questa apparecchiatu ra • Verificare tutti i collegamenti e sostituire tutte le coperture prima della rotazione sull'alimentazi one L'omissione di seguire queste istruz ioni provocherà la morte o di lesioni serie RISCO DE DESCARGA ELÉTTRICA OU EXPLOSÃO • Desconectar o equipamento de toda á energia antes de instalar ou trabalhar com este equipamen to • Verificar todas as conexões e recolocar todas as tampas antes de religar o equipamento O não cumprimento destas instruções pode levar á morte ou lesões sérias. ANNEX - ENVIROMENTAL INFORMATION