CCSO-914X-1000.000

Ultra-Low Phase Noise 1GHz SAW Clock CCSO-914X-1000 True SineWave SAW Based Clock Oscillator 9×14mm SMD 5 Volt CCSO-914X-1000 Model CCSO-914X-1000 is a 1 GHz SAW (surface acoustic wave) Clock Oscillator (CCSO). SAW crystal technology provides low-noise and low-jitter performance with true sinewave output. Features include -146dBc/Hz phase noise at 10 kHz offset, 5V input voltage, -40°C to +85°C operating temperature, FR5 PCB and 9×14 mm SMT package. The oscillator has no sub-harmonic and the second harmonic is typically -20dBc. Applications include: System Clock for Network Clock Generator/Synchronizer, Clock for DDS, Test and Measurement, Avionics, Point-to-Point Radios, and Multi-point Radios. Rev: R Date: 28-Apr-2022 Page 1 of 3 C CRYSTEK CORPORATION 16850 Oriole Road • Fort Myers, Florida 33912 Phone: 239-561-3311 • 800-237-3061 www.crystek.com CCSO-914X-1000 True SineWave SAW Based Clock Oscillator 9×14mm SMD 5 Volt Frequency: Temperature Range: Storage: Input Voltage: 1 GHz -40°C to +85°C -45°C to 90°C 5.0V ± 0.25V Frequency vs Temperature: Input Current: Output: Output Power: Start-Up Time: 2nd Harmonic: Sub-Harmonics: Jitter: ±200ppm Typical 25mA Typical, 35mA Max True SineWave +8dBm Min into 50 Ω Load 2ms Typical, 10ms Max -20dBc Typical, -15dBc Max None See Plot on page 1 Phase Noise Typical: See Plot on page 1 G-sensitivity: 0.9×10-9 per g 0.090 (2.29) 0.040 (1.01) 1 2 4 3 SUGGESTED PAD LAYOUT 0.050 (1.27) 0.560 (14.2) 0.090 (2.29) CRYSTEK CCSO-914X 1 GHz Date Code 0.360 (9.14) 0.180 (4.57) 0.125 (3.18) 0.100 (2.54) 0.560 (14.2) 0.280 (7.11) 0.200 (5.08) PAD FINISH: Immersion Gold (ENIG); 5 micro inches maximum Package Height Options Option L 0.040 (1.02) 0.050 (1.27) 0.200 (5.08) See Table A Standard 0.280 (7.11) inches mm 0.210 5.33 0.135 3.43 Pad Connection 1 2 3 4 N/C GND Output Vdd Table A Rev: R Date: 28-Apr-2022 Page 2 of 3 C CRYSTEK CORPORATION 16850 Oriole Road • Fort Myers, Florida 33912 Phone: 239-561-3311 • 800-237-3061 www.crystek.com CCSO-914X-1000 True SineWave SAW Based Clock Oscillator 9×14mm SMD 5 Volt Crystek Part Number Guide CCSO - 914X L - 1000 #1 #2 #3 #1 Crystek Saw Oscillator #2 Model 914X with -40/85°C Temperature Range #3 Height (L = 0.135") (Blank = 0.210") Frequency vs Temperature RECOMMENDED REFLOW SOLDERING PROFILE Ramp-Up 3°C/Sec Max. TEMPERATURE 260°C Critical Temperature Zone Ramp-Down 6°C/Sec. 217°C 200°C 150°C Preheat 180 Secs. Max. 90 Secs. Max. 8 Minutes Max. 260°C for 10 Secs. Max. NOTE: Reflow Profile with 240°C peak also acceptable. Parameter Mechanical Shock MIL-STD-883, Method 2002, Condition B Mechanical Vibration MIL-STD-883, Method 2007, Condition A Solderability MIL-STD-883, Method 2003 Solvent Resistance MIL-STD-202, Method 215 Resistance to Soldering Heat MIL-STD-202, Method 210, Condition I or J Thermal Shock MIL-STD-883, Method 1011, Condition A Moisture Resistance MIL-STD-883, Method 1004 Crystek Corporation reserves the right to make changes to its products and/or information contained herein without notice. No liability is assumed as a result of its use or application. C Conditions CRYSTEK CORPORATION Rev: R Date: 28-Apr-2022 Page 3 of 3 16850 Oriole Road • Fort Myers, Florida 33912 Phone: 239-561-3311 • 800-237-3061 www.crystek.com