CPLL66-4380

CPLL66-4160-4380 0.60" SQ SMD Features 1GHz-5GHz Range Standard 3 Wire Interface Small layout 0.6" x 0.6" Applications Digital Radio Equipment Fixed Wireless Access Satellite Communications Systems Base Stations Personal Communications Systems Portable Radios Test Instruments Wireless Infrastructure The CPLL66 is a complete PLL/Synthesizer needing only an external frequency reference and supply voltages for the internal PLL (phase lock loop) and VCO (voltage controlled oscillator). The Crystek CPLL66 is programmed using a standard three line interface (Data, Clock and Load Enable). The newly introduced CPLL66 family has been initially released to cover 1GHz to 5GHz in bands. It is housed in a compact 0.6-in. x 0.6-in. x 0.15-in. SMD package which saves board space. Typical phase noise at 4GHz is -90dBc/Hz at 10KHz offset with 0dBm minimum output power. Rev. B Page 1 of 6 CPLL66-4160-4380 0.60" SQ SMD UNITS GHz KHz msec dBm dBc/Hz dBc/Hz dBc/Hz dBc/Hz Volts Volts mA mA -60 -70 -10 -15 5 dBc dBc dBc dBc MHz dBm Ohm Ohm °C P ERFORMANCE SPECIFICATION Frequency Range: Step Size Settling Time Output Pow er: Output Phase Noise @1KHz offset @10KHz offset @100KHz offset @1MHz offset Pow er Supply V1=VCO Supply V2=PLL Supply Supply Current I1=VCO Input Current I2=PLL Input Current Spurious Suppression PFDSpur Reference Feedthru Harmonic Suppression (2nd Harmonic): 2nd 3rd Reference Frequency RF Output Level Input Impedance Rf Output Impedance Operating Temperature Range: MIN 4.160 TYP 2500 1 3 -80 -90 -90 -125 4.75 2.7 5 3 50 25 -70 -80 -15 -25 10 0 100K 50 MAX 4.380 0 6 -75 -85 -85 -130 5.25 3.3 -5 -40 +85 Output Phase Noise: Page 2 of 6 CPLL66-4160-4380 0.60" SQ SMD TOP VIEW 0.600 0.500 0.420 0.340 0.260 0.180 0.100 BOTTOM VIEW 0.00 GND GND GND GND GND GND 0.00 CRYSTEK CPLL66 4160-4380 Date Code 0.140 0.220 0.300 0.380 0.460 0.600 GND REF V2 V1 RF GND GND GND GND GND GND LE DATA CLK LD N/C TOP ORIENTATION MARK LE= Load Enable, CMOS Input DATA= Serial Data Input CLK= Serial Data Input LD= Lock Detect REF= Reference Input V1= Analog Supply Input (VCO) V2= Digital Supply Input (PLL) RF= RF Output BOTTOM ORIENTATION MARK 0.042 0.000 0.000 0.030 0.060 0.220 RECOMMENDED REFLOW SOLDERING PROFILE Ramp-Up 3°C/Sec Max. Critical Temperature Zone Ramp-Down 6°C/Sec. 260°C TEMPERATURE 217°C 200°C 150°C Preheat 180 Secs. Max. 8 Minutes Max. 0.000 Pad Detail 90 Secs. Max. 260°C for 10 Secs. Max. Page 3 of 6 CPLL66-4160-4380 0.60" SQ SMD ENVIRONMENTAL COMPLIANCE Parameter Mechanical Shock Mechanical Vibration Solderability Resistance to Solvents Conditions MIL-STD-883, Method 2002 MIL-STD-883, Method 2007 MIL-STD-883, Method 1014 MIL-STD-883, Method 2016 Programming Guide for CPLL66-XXXX Introduction The CPLL66 uses a simple 3 wire interface to program four internal registers. See Figure 1. Figure 1. Timing Diagram There are four 24 bit registers that need to be programmed. Which register is written into is simply controlled by Control Bits C1 and C2. Table I summarizes the Truth Table for Control Bits C1 and C2. Table I. C2, C1 Truth Table Control Bits C2 C1 0 0 0 1 1 0 1 1 Data Latch R Counter N Counter (A and B) Function Latch (Including Prescaler) Initialization Latch Table II shows the details of the four 24 bit registers. Page 4 of 6 CPLL66-4160-4380 0.60" SQ SMD Table II. Latch Summary REFERENCE COUNTER LATCH LOCK DETECT PRECISION TEST MODE BITS ANTIBACKLASH WIDTH DB17 ABP2 DB16 ABP1 DB15 R14 DB14 R13 DB13 R12 DB12 R11 DB11 R10 CONTROL BITS RESERVED 14-BIT REFERENCE COUNTER DB23 X DB22 0 DB21 0 DB20 LDP DB19 T2 DB18 T1 DB10 R9 DB9 R8 DB8 R7 DB7 R6 DB6 R5 DB5 R4 DB4 R3 DB3 R2 DB2 R1 DB1 C2 (0) DB0 C1 (0) N COUNTER LATCH CP GAIN CONTROL BITS RESERVED 13-BIT B COUNTER 6-BIT A COUNTER DB23 DB22 DB21 G1 DB20 B13 DB19 B12 DB18 B11 DB17 B10 DB16 B9 DB15 B8 DB14 B7 DB13 B6 DB12 B5 DB11 B4 DB10 B3 DB9 B2 DB8 B1 DB7 A6 DB6 A5 DB5 A4 DB4 A3 DB3 A2 DB2 A1 DB1 C2 (0) DB0 C1 (1) FUNCTION LATCH FASTLOCK MODE FASTLOCK ENABLE CP THREESTATE PD POLARITY PRESCALER VALUE CURRENT SETTING 2 DB20 CP16 DB19 CP15 DB18 CP14 DB17 CP13 CURRENT SETTING 1 DB16 CP12 DB15 CP11 DB14 TC4 TIMER COUNTER CONTROL MUXOUT CONTROL COUNTER RESET DB2 F1 POWERDOWN 2 POWERDOWN 1 CONTROL BITS DB23 P2 DB22 P1 DB21 PD2 DB13 TC3 DB12 TC2 DB11 TC1 DB10 F5 DB9 F4 DB8 F3 DB7 F2 DB6 M3 DB5 M2 DB4 M1 DB3 PD1 DB1 C2 (1) DB0 C1 (0) INITIALIZATION LATCH FASTLOCK MODE FASTLOCK ENABLE CP THREESTATE PD POLARITY PRESCALER VALUE CURRENT SETTING 2 DB20 CP16 DB19 CP15 DB18 CP14 DB17 CP13 CURRENT SETTING 1 DB16 CP12 DB15 CP11 DB14 TC4 TIMER COUNTER CONTROL MUXOUT CONTROL COUNTER RESET DB2 F1 POWERDOWN 2 POWERDOWN 1 CONTROL BITS DB23 P2 DB22 P1 DB21 PD2 DB13 TC3 DB12 TC2 DB11 TC1 DB10 F5 DB9 F4 DB8 F3 DB7 F2 DB6 M3 DB5 M2 DB4 M1 DB3 PD1 DB1 C2 (1) DB0 C1 (1) When using the CPLL66 family in a synthesizer application, all four 24 bit registers need to be written into after power-up. After writing all four latches the first time, subsequent frequency step changes can be accomplished by changing the N Counter Latch only. Page 5 of 6 CPLL66-4160-4380 0.60" SQ SMD Programming Crystek p/n: CPLL66-4160-4380 The following is specific programming for CPLL66-4160-4380 (4.160GHz~4.380GHz with 2500KHz Step Size and 10MHz input reference frequency). Program all three registers with the following: Function Latch: 9F8083 H N Counter Latch: 003401 H R Counter Latch: 000010 H The above values will set the CPLL66-4160-4380 to 4.160GHz Page 6 of 6