110

Series 110 ® Commercial 3 /4" (19mm) Diameter, 11/2 and 2 Watt Wirewound Variable Resistors Features • Inexpensive design • Open construction • Four mounting styles • Incorporated fixed resistor available • Available with nylon knob • Interchangeable mounting with CTS Series 115 preset potentiometer • RoHS compliant Electrical and Mechanical Specifications Resistance Range 1 ohm through 10K ohms (linear taper) Resistance Tolerance Standard:±20% Special:±5% or 10% Power Rating, Watts 2 watts @ 55°C derated to no load @ 105°C, mounted on steel panel 1.5 watts @ 55°C derated to no load @ 105°C, mounted on bakelite panel Voltage Rating Determined by resistance value and wattage rating Resistance Taper Standard:Linear taper only Minimum Resistance At ends of rotation: 1% or 1 ohm, whichever is greater Resistance Taper None Incorporated Fixed Resistor A fixed resistor can be incorporated in the Series 110 at the end of CW or CCW rotation to a minimum of 10% of the total resistance. The rotation is shortened by an amount proportional to the ratio of the fixed resistor to the total resistance. Available at extra cost. Angle of Rotation 246°±5°without fixed resistor stop Resistor Adjustment Standard Cross Slot: Provided in drive plate for screwdriver adjustment. Special Molded Knob: Available at extra cost secured to drive plate cross slot. Mounting Types Available Type 110: Solder or clinch-ear mounted Type XPC - 110: Vertically mounted on printed circuit board Type 111: Snap-in mounting Type 112: Eyelet or rivet mounting Rotational Torque 1/ 2 to 10 inch ounces (36 – 720 gf-cm) Terminals Terminals at end of CW or CCW rotation may be omitted. Refer to terminals on all types by numbers 1 and 3 as indicated on line drawings. 1-3 CTS Electronic Components © 2006 CTS Corporation. All right s reser ved. I nf ormation subj ect t o change. www.ctscorp.com 9/30/06 Type 110, Solder or Clinch-Ear Mounted, Long Terminal Length SCREWDRIVER ADJUSTMENT SLOT 246° KNOB OPTIONAL 17.86 .703 1.57 .062 7.14 .281 PRINTED CIRCUIT PANEL 2.39 .094 5.56 .219 1.52 .060 MIN. 1.40 .055 2.79±0.05 .110±.002 20.58±0.05 .810±.002 10.29±0.05 .405±.002 14.30 .563 END C.C.W. ROT. NO. 1 TERM 57° 57° END C.W. ROT. NO. 3 TERM 11.13 .438 10.72 .422 TERM 1.98 x 0.40 .078 .014 40° 1.40 .055 2.79±0.05 .110±.002 40° 9.40±0.05 .370±.002 1.5 .060 19.94 .785 4.37 .172 5.56 .219 16.66 .656 U - Long Terminal Length DIMENSION: mm INCH TYPE M110, Solder Mounted, Medium Terminal Length 14.68 .578 4.44 .175 PRINTED CIRCUIT PANEL 2.39 .094 8.43 .332 9.40±0.05 .370±.002 1.5 .060 19.9±0.4 .783±.016 246° rot screwdriver adjustment slot KNOB OPTIONAL 20.58±0.05 .810±.002 10.29±0.05 .405±.002 1.52 .060 MIN. 1.40 .055 2.79±0.05 .110±.002 11.1 .437 1.57 .062 14.3 .562 end c.w. rot. no. 1 terminal 57° 57° end c.w. rot. no. 3 terminal 1.98 x 0.36 .078 .014 10.67 .420 2.87 .113 REF. 40° 1.40 .055 2.79±0.05 .110±.002 40° M - Medium Terminal Length DIMENSION: mm INCH TYPE XPC110, Vertically Mounted 246° 21.59 .850 11.91 .469 2.77 DIA. .109 5.77 .227 28.17 1.109 7.62 .300 15.24 .600 23.42 .922 12.7 .500 4.75 .187 57° END C.C.W. ROT. NO. 1 TERM 57° END C.W. ROT. NO. 3 TERM END TERMINAL 1.98X.081 .078 .032 CENTER TERMINAL 1.98X0.41 .078 .016 DIMENSION: mm INCH Type 111, Snap-In Mounted END C.C.W ROT NO.1 TERM 7.14 .281 MOUNTING PANEL 5.54 .218 10.11 .398 1.57 .062 2.79 .110 246° 21.59 .850 14.3 .563 9.40 .370 2 1.5 60 .0 20.22 .796 KNOB OPTIONAL 57° 1.4 .055 19.94 .785 57° 11.13 .438 END C.W ROT NO.3 TERM 1.57 .062 10.72 .422 3.96 .156 5.56 .219 17.86 .703 40° 1 .05 .40 5 2 .11 .79 0 40° SCREWDRIVER ADJUSTMENT SLOT DIMENSION: mm INCH Type 112, Eyelet or Rivet Mounted 240° ROT. 31.75 1.25 25.4 1.000 MOUNTING PANEL KNOB OPTIONAL 19.94 .785 3.45 .136 9.53 .375 57° 40° 40° 57° 14.3 .563 OPTIONAL TERM LOC. B 25.4 1.000 12.7 .500 Ø3.45 .136 END C.C.W ROT NO.1 TERM END C.W ROT NO.3 TERM SCREWDRIVER ADJUSTMENT SLOT TERM LOC. A 11.13 .438 1.57 .062 TERMS 1.98/.078 X 0.4/.016 R8.64 .340R. 40° 40° DIA. OF HOLE TO SUIT TERM CLEARANCE. 1.57 .062 9.53 .375 8.74 .344 DIMENSION: mm INCH Ordering Information 110 SERIES MOUNTING DESIGNATION 110 – CLINCH EAR MOUNT OR VERTICAL MOUNT 111 – SNAP-IN MOUNT 112 – EYELET MOUNT U A KNOB OPTION A – NO KNOB B – .438" (11.1mm) LONG KNOB 103 RESISTANCE CODE EXAMPLES CODERESISTANCE 5A0 5 OHMS 500 50 101 100 501 500 102 1K 252 2.5K 502 5K 103 10K 203 20K B RESIST TOL A – ±10% B – ±20% D – ± 5% 1 TAPER 1 – LINEAR TERMINAL STYLE X – PC MOUNT (XPC-110 AND 112 ONLY) U – PC TERMINALS FORMED TO FRONT (110, 111, 112 ONLY) M – PC TERMINALS FORMED TO FRONT MEDIUM LENGTH (110 ONLY) 3-3 CTS Electronic Components © 2006 CTS Corporation. All right s reser ved. I nf ormation subj ect t o change. www.ctscorp.com 9/30/06