206-8ST

Series 206 Through-Hole DIP Switch ▪ Available with SPST, SPDT, DPST, 3PST circuit choices ▪ Available with low profile, standard, or extended actuator heights. Consult the ordering information for options. ▪ Blue housing ▪ RoHS compliant ▪ Optional top tape seal for board spray washing ▪ Gold plated contacts Description The terminals are molded into the thermoset base and provide an electrostatic discharge shield rating to 22KV when the front row of terminals are connected to ground. The optimized contact design incorporates a dimpleto-flat surface wiping interface for long-term contact corrosion resistance, making the 206 series an ideal choice for many applications. Ordering Information Series Number of Poles 206- Number of B Number of Throws S Switch Positions 1 20212124 2 1 1 2 Code No. of poles Blank 1 2 3 For SPST Single pole Double pole 3 poles 1 Spec. Blank 1 2 For SPST Single throw Double throw 1 2 3 4 5 6 7 8 9 10 12 E Top Tape Seal S 1 position 2 positions 3 positions 4 positions 5 positions 6 positions 7 positions 8 positions 9 positions 10 positions 12 positions Code Actuation Preset T Spec. Blank Standard (0.89mm/.035”) Extended (3.43mm/.135”) (SPST only) Low profile (Flush) (SPST & SPDT only) E LP Code Bottom epoxy seal Blank No epoxy seal Epoxy seal (Required for 206-1S) S Notes: Bottom Epoxy Seal N E of switch Code No. positions Code Actuator Height 1.Contact CTS for other common features not listed. Code BLANK N Spec. Ship at OFF position Ship at ON position (SPST, DPST & 3PST only) Code Top tape seal Blank No top tape seal Top tape seal (Not available for extended actuator or 1-position SPST DIP switch) T 2. Not available in a Double Pole Double Thow (DPDT) construction 2019-2-27 Rev. E Page 1 of 5 ©2019 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote. Series 206 Through-Hole DIP Switch Electrical Specifications Parameter Contact Resistance Insulation Resistance Dielectric Strength Switch Capacitance Conditions & Remarks Initial At end of life Between insulated terminals 500 VAC between adjacent switches Between adjacent closed switches Min 1000 Nonswitching Rating SPST SPDT DPST 3PST Circuit Max 50 100 1 1 1 1 Unit milliohms Megohms 1 minute 5.0 pF 100 or 50 12 6 6 4 mA or VDC Position Position Position Position Mechanical and Environmental Actuation Life Soldering Shock Vibration Seal Marking Packaging: Operating Temperature Range Storage Temperature Range 2019-2-27 Rev. E 10,000 cycles switching 50mA @ 24VDC Maximum wave temperature, 260°C for 5 seconds Per MIL-STD-202F, method 213B, condition A(50G’s) with no contact inconsistencies greater than 1 microsecond Per MIL-STD-202F, method 204D, condition B (.06” or 15G’s between 10 HZ to 2K HZ) with no contact inconsistencies greater than 1 microsecond Bottom epoxy seal optional Optional top tape seal for board spray washing Special side or top marking available-consult CTS Standard anti-static tube packaging -55°C to +85°C -55°C to +85°C Page 2 of 5 ©2019 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote. Series 206 Through-Hole DIP Switch Mechanical Specifications Figure 1 - SPST Figure 2 – SPDT Figure 3 – DPST 2019-2-27 Rev. E Page 3 of 5 ©2019 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote. Series 206 Through-Hole DIP Switch Figure 4 - 3PST Figure 5 – Low Profile Actuators (SPST & SPDT only) Figure 6 – Extended Actuators (SPST only) 2019-2-27 Rev. E Page 4 of 5 ©2019 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote. Series 206 Through-Hole DIP Switch 2019-2-27 Rev. E Page 5 of 5 ©2019 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote.