208-8ST

Series 208 Through-Hole DIP Switch ▪ Available with SPST circuit choices ▪ Available with low profile, standard, or extended actuator heights. Consult the ordering information for options. ▪ Black housing ▪ RoHS compliant ▪ Optional top tape seal for board spray washing Description The terminals are molded into the thermoset base and provide an electrostatic discharge shield rating to 22KV when front row of terminals are connected to ground. Tin plated contact design incorporates a dimple-to-flat surface wiping interface for contact corrosion resistance, making it the economical choice for many applications. Ordering Information Series Number of S Switch Positions 208- 1 of switch Code No. positions 1 2 3 4 5 6 7 8 9 10 12 1 position 2 positions 3 positions 4 positions 5 positions 6 positions 7 positions 8 positions 9 positions 10 positions 12 positions Actuator Height E Code Blank E LP Bottom Epoxy Seal Top Tape Seal Actuation Preset S T N Code Spec. Standard (0.89mm/.035”) Extended (3.43mm/.135”) Low profile (Flush) BLANK N Code Bottom epoxy seal Blank No epoxy seal Epoxy seal (Required for 208-1S) S Code Top tape seal Blank No top tape seal Top tape seal (Not available for extended actuator or 1-position SPST DIP switch) T Notes: 1.Contact CTS for other common features not listed. 2019-3-25 Rev. A Spec. Ship at OFF position Ship at ON position Page 1 of 4 ©2019 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote. Series 208 Through-Hole DIP Switch Electrical Specifications Parameter Contact Resistance Insulation Resistance Dielectric Strength Switch Capacitance Conditions & Remarks Initial At end of life Between insulated terminals 500 VAC between adjacent switches Between adjacent closed switches Min 1000 Nonswitching Rating Circuit SPST Max 100 500 1 Unit milliohms Megohms 1 minute 5.0 pF 100 or 50 12 mA or VDC Position Mechanical and Environmental Actuation Life Soldering Shock Vibration Seal Marking Packaging: Operating Temperature Range Storage Temperature Range 2019-3-25 Rev. A 2,000 cycles switching 50mA @ 24VDC Maximum wave temperature, 260°C for 5 seconds Per MIL-STD-202F, method 213B, condition A(50G’s) with no contact inconsistencies greater than 1 microsecond Per MIL-STD-202F, method 204D, condition B (.06” or 15G’s between 10 HZ to 2K HZ) with no contact inconsistencies greater than 1 microsecond Bottom epoxy seal optional Optional top tape seal for board spray washing Special side or top marking available-consult CTS Standard anti-static tube packaging -55°C to +85°C -55°C to +85°C Page 2 of 4 ©2019 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote. Series 208 Through-Hole DIP Switch Mechanical Specifications Figure 1 - SPST Figure 2 – Low Profile Actuators Figure 3 – Extended Actuators 2019-3-25 Rev. A Page 3 of 4 ©2019 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote. Series 208 Through-Hole DIP Switch 2019-3-25 Rev. A Page 4 of 4 ©2019 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote.