219-5LPSTR

® Electrocomponents Series 219 Data Sheet SMD DIP Switch Surface Mount DIP Switch — Auto Placeable Features Optimized Mechanical Features • Positive detent separate from contactor • Available low profile, medium, and extended height actuators • Gull-wing and "J" lead terminal configurations • Tube or tape and reel packaging available Optimized Contact System • Redundant, wiping contact • Contactor does not deflect during actuation Premium Materials • Gold plated beryllium copper contacts • High temperature materials (UL94V-0) • RoHS compliant • Optional top tape seal for board spray washing Electrical and Mechanical Specifications Switch Function SPST- 2 through 10 and 12 positions Switch Contact Resistance 25 milliohms maximum initial 50 milliohms maximum at the end of life Insulation Resistance 1,000 megohms minimum between insulated terminals Dielectric Strength 500 VDC for 1 minute between adjacent switches Nonswitching Rating 100 mA or 50 VDC maximum Switch Capacitance 5 pF maximum between adjacent closed switches Operating Temperature - 55°C to +85°C Actuation Life 2,000 cycles switching 100 mA @ 20 VDC or 0.1 mA @ 5 VDC (dry circuit) 1-2 CTS Electrocomponents Coplanarity 0.10mm (.004") maximum Allowable Solder Time Up to 60 seconds at 260°C Vibration Per MIL-STD-202F, method 204D, condition B (.06" or 15 G’s between 10 HZ to 2K HZ) with no contact inconsistencies greater than 1 microsecond. Shock Per MIL-STD-202F, method 213B, condition A (50 G’s) with no contact inconsistencies greater than 1 microsecond. Sealing Standard bottom seal Optional top tape seal for board spray washing Marking Special marking available consult CTS. Packaging Standard : Anti-static tube packaging Optional : Tape and reel packaging © 2017 CTS Corporation. All rights reserved. Information subject to change. 06/14/17 www.ctscorp.com CTS SERIES 219 SMT CONTACT FEATURES 1. Value of Redundant (Bifurcated) Gold Plated Contacts: Redundancy dramatically reduces the probability of contact failure while gold contact material provides the highest environmental protection, IMPROVING RELIABILITY. "A" Overall Dimension 6.55/.258 9.09/.358 11.63/.458 14.17/.558 16.71/.658 19.25/.758 21.79/.858 24.33/.958 26.87/1.058 31.95/1.258 2. Value of Wiping Contact Action: Clean contact area, IMPROVING RELIABILITY. 3. Value of Contactor Not Deflecting During Actuation: Constant contact pressure eliminates overstressing contacts, IMPROVING RELIABILITY. 4. Value of Detent Separate from Contactor: Separate detent allows optimization of nondeflecting contactor and detent designs, IMPROVING RELIABILITY. 2. Wiping contact action 1. Redundant (bifurcated) gold plated cross radial contactor 4. Detent separate from contactor 3. Contactor does not deflect during actuation Gull Wing Terminals Medium Height Actuator "J" Bend Terminals Low Profile Actuator 1.0 X45° CHAMFER (2) .039 TRAVEL 0.70 .028 DATE CODE CTS DATE CODE ON 1 2 3 4 5 10 1.50 .059 TYP. 2.54 .100 TYP. 11 12 1 0.55±0.08 .022±.003 +0.05 3.80 -0.10 .150 +.002 -.004 2 4 3 5 10 11 12 1.50 .059 TYP. 8.00 .315 +0.13 0.25 -0.00 +.005 .010 -.000 "A" 8.00 .315 ±0.30 ±.012 +0.05 3.80 -0.10 .150 +.002 -.004 STANDOFF 0.25±0.10 .010±.004 SOLDER COATED CTS 2.54 .100 TYP. TYP. "A" ±0.30 ±.012 0.55 .022 3.62 .143 6.70±0.25 .264±.010 219 6.70±0.25 3.62 .264±.010 .143 1.0 X45° CHAMFER (2) .039 TRAVEL 0.70 .028 219 ON No. of Switch positions 2 3 4 5 6 7 8 9 10 12 1.50 .059 7.62±0.20 .300±.008 9.91±0.08 .390±.003 Gull Wing Surface Mount Pad Layouts 0.55±0.08 .022±.003 STANDOFF 1.27±0.10 .050±.004 8.51 .335 MAX TYP. 1.3 .050 "J" Bend Surface Mount Pad Layouts 2.44 .096 6.17 .243 8.60 .339 2.54 .100 TYP. 1.13 .044 Ordering Information 11.04 .435 4.57 .180 6.73 .265 TYP. DIMENSION: 219 – 12 XX: NO. OF POSITIONS E: EXTENDED HEIGHT ACTUATOR(0.60mm/.024") M: MEDIUM HEIGHT ACTUATOR(0.25mm/.010") LP: LOW PROFILE ACTUATOR(Flush) mm LP S 1.13 .044 TYP. 2.54 .100 TYP. inch T J R 8.89 .350 F BLANK: SHIP AT ON POSITION F: SHIP AT OFF POSITION BLANK : ANTI-STATIC TUBE PACKAGING R: TAPE AND REEL PACKAGING BLANK: GULL-WING TERMINAL J: "J" BEND TERMINAL BLANK: NO TOP TAPE SEAL * T : TOP TAPE SEAL * Not available on extended actuator S: BOTTOM SEAL © 2017 CTS Corporation. All rights reserved. Information subject to change. 2-2 CTS Electronic Components 06/14/17 www.ctscorp.com