292V1X00B

Series 292 20mm Optical Ring Encoder       Compact Ø20mm size package 3 million cycles rotational life (1 million cycles with detent) 24 PPR resolution Wide operating temperature range (-10°C to +85°C) 5.0 VDC and 3.3 VDC power options Integrated Schmitt trigger and pull-up resistor Applications      Medical diagnostic equipment Industrial automation controls Automotive HVAC controls Infotainment controls Professional audio and lighting equipment Description The Series 292 optical ring encoder provides a reliable and durable solution to applications that require extended rotational life where traditional mechanical contacting designs fall short. The hollow shaft design allows the engineer to integrate an additional push switch or LED in the center of the unit. Power options allow for use in standard or energy efficient circuits. The integrated Schmitt trigger and pull up resistor reduces the number of components required when adding an encoder to a circuit. The reduced number of components translates into cost savings and reduction in required PCB space. Ordering Information Series Terminal Type 292 V1 Code V1 Output Combination X24 A Spec. .050” pitch pin rear facing Code X00 X24 2020-02-19 Rev. A Voltage www.ctscorp.com Output Combination 24 PPR No detents 24 PPR 24 detents Code Spec. A B 5.0 VDC 3.3 VDC Page 1 of 3 ©2020 CTS® CTS® Corporation. Corporation. Information/product(s) Information/product(s) subject subject to to change. change. No No warranty warranty that that product(s) product(s) will will meet meet the the stated stated specifications specifications for for customer customer specific specific applications applications or or test test ©2020 equipment. Visit Visit www.ctscorp.com www.ctscorp.com for for list list of of applicable applicable patent(s), patent(s), more more information, information, or or to to request request aa quote. quote. equipment. Series 292 20mmOptical Ring Encoder Electrical Specifications Encoder Function Parameter Conditions & Remarks Input Voltage Supply Current Dielectric Strength Insulation Resistance Output Code Sink Current Power Consumption Logic Output Resolution 5.0 VDC 3.3 VDC For 1 minute At 50 VDC 2-Bit Quadrature Channel A leads Channel B by 90°±45˚ during clockwise rotation 5.0 VDC 3.3 VDC 5.0 VDC 3.3 VDC Logic High Logic Low Min Nominal Max 4.95 2.97 5.0 3.3 5.50 3.63 30 20 50 10 mA mA VDC MegΩ 150 80 mW mW 2.0mA 1.0mA 3.8 0.8 24 Unit VDC VDC Pulses per Revolution Mechanical and Environmental Wave Soldering Operating Temperature: Storage Temperature: Rotational Life Rotational Torque Non-detent Detent Detent Position Travel Operational Speed RoHS IP Rating Marking Packaging Weight Maximum temperature of 260°C for 5 seconds -10°C to +85°C -10°C to +100°C 3 million cycles (no detent @ 30 RPM) 1 million cycles (with detent @ 30 RPM) 500k cycles (with detent @30 RPM and 300 to 350 gf of side load) 10 gf-cm max. 78 ± 30 gf-cm Every 15° ± 3° of mechanical rotation 360˚ endless 120 RPM max. Fully compliant to RoHS3 directive IP 50 CTS logo, part number, date code Standard anti-static tray packaging 1.2g All testing is performed at room ambient conditions except as noted. Users should verify device actual performance in their specific applications RoHS3 Directive 2015/863 Amendments of Annex II on March 31,2015 Custom and value-added options available on request. Please contact your sales representative for additional information. 2020-02-19 Rev. A www.ctscorp.com Page 2 of 3 ©2020 CTS® CTS® Corporation. Corporation. Information/product(s) Information/product(s) subject subject to to change. change. No No warranty warranty that that product(s) product(s) will will meet meet the the stated stated specifications specifications for for customer customer specific specific applications applications or or test test ©2020 equipment. Visit Visit www.ctscorp.com www.ctscorp.com for for list list of of applicable applicable patent(s), patent(s), more more information, information, or or to to request request aa quote. quote. equipment. Series 292 20mmOptical Ring Encoder Mechanical Specifications Channel A leads channel B in the CW direction, and lags in the CCW direction. Schmitt trigger and pull-up resistor (4.7kΩ) are integrated into the optical encoder eliminating the necessity to use external pullup resistors for the application circuit. 2020-02-19 Rev. A www.ctscorp.com Page 3 of 3 ©2020 CTS® CTS® Corporation. Corporation. Information/product(s) Information/product(s) subject subject to to change. change. No No warranty warranty that that product(s) product(s) will will meet meet the the stated stated specifications specifications for for customer customer specific specific applications applications or or test test ©2020 equipment. Visit Visit www.ctscorp.com www.ctscorp.com for for list list of of applicable applicable patent(s), patent(s), more more information, information, or or to to request request aa quote. quote. equipment.