CMT-1603

Part No: CMT-1603 Description: piezo audio transducer Date: 9/19/2006 Unit: mm Page No: 1 of 6 Specifications Operating voltage Current consumption Sound pressure level Electrostatic capacity Operating tempurature Storage tempurature Dimensions Weight Material Terminal RoHS 25 Vp-p max. 3 mA max. at 3 Vp-p, square wave, 4.0 KHz 70 db min. at 10 cm / 3 Vp-p, square wave, 4.0 KHz 14,000 pF ±30% at 1 KHz / 1 V -30 ~ +70° C -40 ~ +85° C L16.0 x W16.0 x H2.6 mm 0.96 g max. LCB (White) + PCB (FR4) Pin type (Sn Plating) yes Appearance Drawing Tolerance: ±0.2 Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CMT-1603 Description: piezo audio transducer Date: 9/19/2006 Unit: mm Page No: 2 of 6 Typical Frequency Response Curve Measurement Method S.P.L. Measuring Circuit Input Signal: 3 V p-p, 4.0 KHz, Square Wave Mic: RION UC 30 S.G.: Hewlett Packard 33120A Function Generator or equivalent Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CMT-1603 Description: piezo audio transducer Date: 9/19/2006 Unit: mm Page No: 3 of 6 Mechanical Characteristics Item Solderability Evaluation Standard Test Condition 95% of the surface of the lead Lead terminals are immersed in rosin for pads should be covered with 5 seconds and then immersed in solder bath solder. of 270 ±5°C for 2 ±0.5 seconds. 1) IR Reflow Pre-heating conditions should be 150~200°C for 60 to 180 seconds. Ascending time up to 245°C should be longer than 55 seconds. Heating conditions should be within 20 to 40 seconds at 245°C min. Peak temperature should be lower than 255°C. The transducer should be measured after 1 hour in normal No interference in operation. conditions. 2) Soldering Iron A soldering iron of 270±5°C should be placed 0.5mm away from the electrode of the transducer. Melted solder should be applied to the electrode for 3±1 seconds. The transducer should be measured after 4 hours in normal conditions. For 10 seconds, the force of 9.8N (1.0kg) is applied to each terminal in axial direction. The transducer should be subjected to a vibration cycle of 10 to 55 Hz band of vibration frequency for a period of 1 minute. Total peak amplitude should be 1.5mm. The vibration test should consist of 2 hours per axis in each axial direction (X, Y, Z) for a total of 6 hours. Soldering Heat Resistance Terminal Mechanical Strength Vibration No damage or cutting off. After the test, the part should meet specifications without any damage in appearance or performance except for SPL. The SPL should be within ±10dB compared with the initial measurement. Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CMT-1603 Description: piezo audio transducer Date: 9/19/2006 Unit: mm Page No: 4 of 6 Environment Test Item High temp. test Low temp. test Humidity test Temp. cycle test Test Condition After being placed in a chamber at +85°C for 240 hours. After being placed in a chamber at -40°C for 240 hours. After being placed in a chamber at +40°C and 90±5% relative humidity for 240 hours. The part shall be subjected to 5 cycles. One cycle will consist of: Evaluation Standard The transducer should be measured after being placed at +25°C for 4 hours. The value of the oscillation frequency/current consumption should be ±10% compared to the initial measurements. The SPL should be within ±10dB compared to the initial measurements. Reliability Test Item Operating (Life Test) Test Condition 1. Continuous life test: The part will be subjected to 48 hours of continuous operation at +55°C with rated voltage applied. 2. Intermittent life test: A duty cycle of 1 minute on, 1 minute off, a minimum of 5,000 times at room temp (+25 ±2°C) with rated voltage applied. Evaluation Standard The transducer will be measured after being placed at +25°C for 4 hours. The value of the oscillation frequency/current consumption should be ±10% compared to the initial measurements. The SPL should be within ±10dB compared to the initial measurements. Test Conditions Standard Test Condition Judgement Test Condition a) Tempurature: +5 ~ +35°C a) Tempurature: +25 ±2°C b) Humidity: 45 - 85% b) Humidity: 60 - 70% c) Pressure: 860-1060 mbar c) Pressure: 860-1060 mbar Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CMT-1603 Description: piezo audio transducer Date: 9/19/2006 Unit: mm Page No: 5 of 6 Recommended Temperature Profile for Reflow Oven Note: 255°C is less than 20 seconds, but only pass the lead free reflow once Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CMT-1603 Description: piezo audio transducer Date: 9/19/2006 Unit: mm Page No: 6 of 6 Packaging Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062