CSS-73B16K

Part No: CSS-73B16K Description: magnetic buzzer Date: 12/28/2007 Unit: mm Page No: 1 of 5 RoHS Specifications Rated voltage Operating voltage Mean current Coil resistance Sound output 3.6 Vo-p 2.5 - 4.5 Vo-p 100 mA max. 16.0 ±2.4 Ω Min. 87 (Typical 92) dBA Applying rated voltage, 2730 Hz square wave, ½ duty Distance at 10cm (A-weight free air). Applying rated voltage of 2730 Hz, square wave, ½ duty. Rated frequency Operating tempurature Storage tempurature Dimensions Weight Material Terminal RoHS 2,730 Hz -30 ~ +70° C -40 ~ +85° C L8.5 x W8.5 x H4.0 mm 0.6 g L.C.P. (White) SMD type (Au Plating) yes See attached drawing See attached drawing Frequency Response Curve Phone: 800.275.4899 Fax: 503.612.2383 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CSS-73B16K Description: magnetic buzzer Date: 12/28/2007 Unit: mm Page No: 2 of 5 Appearance Drawing Tolerance: ±0.5 Measurement Method Phone: 800.275.4899 Fax: 503.612.2383 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CSS-73B16K Description: magnetic buzzer Date: 12/28/2007 Unit: mm Page No: 3 of 5 Mechanical Characteristics Item Solderability Soldering Heat Resistance Terminal Mechanical Strength Test Condition Lead terminals are immersed in solder bath of +270 ±5°C for 3 ±1 seconds. The product follows the reflow temperature curve to test its reflow thermo stability. Lead pads shall be soldered onto the pc board and the force of 9.8 N (1.0 kg) shall be applied behind the part for 10 seconds. The buzzer will be measured after applying a vibration amplitude of 1.5 mm with 10 to 55 Hz band of vibration frequency to each of the 3 perpendicular directions for 2 hours. The part is to be dropped from a height of 75 cm onto a 40 mm thick wooden board 3 times in 3 axis (X, Y, Z) for a total of 9 drops. Evaluation Standard 95% surface of lead pads must be covered with fresh solder. No in interference in operation. No damage or cutting off. Vibration Drop Test After the test, the part shall meet specifications without any damage to the appearance and the SPL should be within ±10 dBA of the initial SPL. Environment Test Item High temp. test Low temp. test Thermal shock Test Condition The part will be subjected to +85°C for 96 hours. The part will be subjected to -40°C for 96 hours The part will be subjected to 10 cycles. One cycle will consist of: Evaluation Standard Temp./Humidity cycle The part shall be subjected to 10 cycles. One cycle will last for 24 hours and consist of: After the test, the part shall meet specifications without any damage to the appearance or performance and the SPL after 4 hours at 25°C should be within ±10 dBA of the initial SPL. Phone: 800.275.4899 Fax: 503.612.2383 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CSS-73B16K Description: magnetic buzzer Date: 12/28/2007 Unit: mm Page No: 4 of 5 Mechanical Characteristics Item Operating (Life Test) Evaluation Standard Test Condition 1. Continuous life test: The part will be subjected to 72 hours at +55°C After the test, the part shall meet specifications without any with 3.6 V, 2730 Hz applied. damage to the appearance. After 4 hours at 25°C, the SPL 2. Intermittent life test: should be within ±10 dBA of the A duty cycle of 1 minute on, 1 minute off, a initial SPL. minimum of 10,000 times at room temp (+25±10°C) with 3.6 V, 2730 Hz applied. Test Conditions Standard Test Condition Judgement Test Condition a) Tempurature: +5 ~ +35°C a) Tempurature: +25±2°C b) Humidity: 45 - 85% b) Humidity: 60 - 70% c) Pressure: 860 - 1060 mbar c) Pressure: 860 - 1060 mbar Recommended Temperature Profile for Reflow Oven Phone: 800.275.4899 Fax: 503.612.2383 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CSS-73B16K Description: magnetic buzzer Date: 12/28/2007 Unit: mm Page No: 5 of 5 Recommended Land Pattern Packaging Phone: 800.275.4899 Fax: 503.612.2383 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062