V7802-1000-SMT

date page 11/23/2011 1 of 6 SERIES: V78-1000-SMT │ DESCRIPTION: NON-ISOLATED SWITCHING REGULATOR FEATURES • • • • • • • • 1 A current output high efficiency up to 92% no heat sink required SMT package remote on/off control low ripple and noise short circuit protection, thermal shutdown wide temperature( -40°C~+85°C) RoHS MODEL V7802-1000-SMT V7803-1000-SMT V7805-1000-SMT V7806-1000-SMT Notes: 1. 20 MHz bandwidth 2. Measured at Vin min. and 100% load input voltage range (Vdc) output voltage (Vdc) output current (mA) output power max (W) ripple and noise1 max (mVp-p) efficiency level2 typ (%) 5 ~ 18 5 ~ 18 7 ~ 18 8.5 ~ 18 2.5 3.3 5.0 6.5 1,000 1,000 1,000 1,000 2.5 3.3 5 6.5 35 35 35 35 82 84 90 92 PART NUMBER KEY V78 XX - XXXX -SMT Base Number Output Voltage Output Current cui.com CUI Inc │ SERIES: V78-1000-SMT │ DESCRIPTION: NON-ISOLATED SWITCHING REGULATOR date 11/23/2011 │ page 2 of 6 INPUT parameter operating input voltage input filter remote on/off on/off control current conditions/description 2.5, 3.3 V models 5.0 V model 6.5 V model capacitor on: off: on: off: open or 1.2 < Vc ≤ 6 V Vc < 0.6 V open or 1.2 < Vc ≤ 6 V GND or Vc < 0.4 V 100 200 μA min 5.0 7.0 8.5 typ 12 12 12 10 max 18 18 18 units Vdc Vdc Vdc μF OUTPUT parameter line regulation load regulation voltage accuracy adjustability1 switching frequency temperature coefficient quiescent current max capacitance load Notes: 1. Output voltage adjustment must meet Vin-Vo > 2V requirement, see adjustment resistor values on page 4. conditions/description measured from low line to high line at 100% load measured from 10% to full load at nominal input measured from low line to high line at 100% load 2.5 3.3 5.0 6.5 V V V V model model model models, fixed output min typ ±0.2 ±0.4 ±2 max ±0.5 ±1.0 ±3 3.9 5.5 6.5 units % % % Vdc Vdc Vdc MHz 1.5 1.8 2.5 1.4 PWM type -40°C ~ +85°C ambient ±0.02 1 3 1,000 %/°C mA μF PROTECTIONS parameter short circuit protection thermal shutdown current limit conditions/description continuous, automatic recovery (hiccup mode) internal IC junction 150 1.8 °C A min typ max units SAFETY AND COMPLIANCE parameter thermal resistance EMI/EMC RoHS compliant MTBF EN55022, class A and class B (refer to page 4), IEC/EN 61000-4-2 Criteria B, IEC/EN 61000-4-4 Criteria B, IEC/EN 61000-4-5 Criteria B (refer to page 4) yes 25°C (MIL-HDBK-217K) 1,000,000 hours conditions/description min typ max 90 units °C/W ENVIRONMENTAL parameter case operating temperature operating temperature storage temperature storage humidity power derating above 71°C -40 -55 conditions/description min typ max 100 85 125 95 units °C °C °C % cui.com CUI Inc │ SERIES: V78-1000-SMT │ DESCRIPTION: NON-ISOLATED SWITCHING REGULATOR date 11/23/2011 │ page 3 of 6 MECHANICAL parameter dimensions case material weight conditions/description 15.24 x 8.50 x 7.25 mm (0.600 x 0.335 x 0.285 inch) Plastic (UL94-V0) 2.3 g min typ max units MECHANICAL DRAWING units: mm [in] pin tolerance: ±0.10 mm [±0.004 in] general tolerance: ±0.25 mm [±0.010 in] 2.54 0.100 10 9 7 6 12.10 0.476 1 5 10.16 0.400 15.24 0.600 8.50 0.335 1.13 0.044 5° max 7.25 0.285 7.00 0.276 DETAIL A SCALE 10 : 1 0.25 0.010 A RECOMMENDED FOOTPRINT 11.02 [0.434] 10 9 76 5 2.54 [0.100] PIN CONNECTIONS 1 7,9 5 6 10 +Vin GND +Vout Vadj On/Off 1 1.80 [0.071] 1.00 [0.039] 2.54 [0.100] cui.com CUI Inc │ SERIES: V78-1000-SMT │ DESCRIPTION: NON-ISOLATED SWITCHING REGULATOR date 11/23/2011 │ page 4 of 6 TYPICAL APPLICATION CIRCUIT Vin DERATING CURVE Vo u t V7805-1000-SMT 1 10 C1 ON/OFF 7,9 6 R1 C2 C4 470pF 5 120 100 Output Power (%) 80 60 Safe Operating Area R2 GND GND 40 20 0 -40 0 40 71 85 120 Operating Temperature (°C) 1. C1 and C2 are required for best performance and should be fitted close to the converter pins. 2. See the capacitor values for C1 and C2 in the external capacitor table below. These can be increased if required and tantalum or low ESR electrolytic capacitors will also suffice. 3. No parallel connection or plug and play. EXTERNAL CAPACITOR TABLE MODEL V7802-1000-SMT V7803-1000-SMT V7805-1000-SMT V7806-1000-SMT C1 (Ceramic) 10 μF / 25 V 10 μF / 25 V 10 μF / 25 V 10 μF / 25 V C2 (Ceramic) 22 μF / 16 V 22 μF / 16 V 22 μF / 16 V 22 μF / 16 V REFLOW SOLDERING PROFILE 2 50 P ea k .Te m p 2 4 0 C 10 Se c M ax 220 C 90 S ec Max (>2 2 0 C) Temperature (°C) 2 00 1 50 APPLICATION EXAMPLE 100 50 0 Vin C1 1 DC/DC Converter L 5 +Vo u t 7 ,9 C4 6 470pF C2 22 F GND To reduce output ripple, it is recommended to add a LC filter to the output port. L: Recommended parameter 10 ~ 47μH. cui.com Load Time (seconds) CUI Inc │ SERIES: V78-1000-SMT │ DESCRIPTION: NON-ISOLATED SWITCHING REGULATOR date 11/23/2011 │ page 5 of 6 ADJUSTMENT RESISTOR VALUES MODEL Vo (nominal) Vadj (V) 1.5 1.8 2.5 3.0 3.3 3.6 3.9 4.5 4.9 5.0 5.1 5.5 6.0 6.5 51.1 104.3 V7802 2.5 V R1 (kΩ) R2 (kΩ) 88.7 41.3 20.1 8.0 15.4 87 339 V7803 3.3 V R1 (kΩ) R2 (kΩ) 121 51.0 16.6 8.0 6.5 5.2 1.1 9.7 30.5 48.8 75 115 338 1,835 V7805 5.0 V R1 (kΩ) R2 (kΩ) 426 58.7 16.9 3.2 The R1, R2 in the above table are used to set the output voltage. If no need to adjust the output voltage, connect a ceramic capacitor to GND with 470pF typical value for increase immunity. Insure the output voltage is in the adjust range or else may cause permanent damage to the device. Fine-tune output voltage must appease Vin-Vo>2V. EMC RECOMMENDED CIRCUIT +Vin L1 V7805-1000-SMT 1 10 7,9 6 5 + Vo +Vin L2 V7805-1000-SMT 1 10 7,9 6 5 + Vo T VS C1 RL ON/O FF C2 47 0p F C3 RL O N/O FF C4 470 pF GN D GND GND G ND TVS: SMCJ18A, 1500W L1: 68 μH C1: 680 μF / 50 V electrolytic capacitors L2: 516 μH C3: 1 μF / 50 V ceramic capacitor cui.com CUI Inc │ SERIES: V78-1000-SMT │ DESCRIPTION: NON-ISOLATED SWITCHING REGULATOR date 11/23/2011 │ page 6 of 6 REVISION HISTORY rev. 1.0 description initial release date 11/23/2011 The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 CUI offers a two (2) year limited warranty. Complete warranty information is listed on our website. Fax 503.612.2383 cui.com techsupport@cui.com CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.