VBSD1-S15-S3.3-DIP

rev. rev. page date 1 of 3 09/2008 PART NUMBER: VBSD1-DIP series DESCRIPTION: dc-dc converter description Designed to convert fixed voltages into an isolated voltage, the VBSD1-DIP series is well suited for providing board-mount local supplies in a wide range of applications, including mixed analog/digital circuits, test & measurement equip., process/machine controls, datacom/telecom fields, etc... The semi-regulated output can be followed by 3-terminal regulators to provide output protection, in addition to output regulation. features · isolated 1 W output ·temperature range: -40°C~+85°C ·unregulated ·high efficiency to 80% ·single voltage output ·small footprint ·DIP package style ·industry standard pinout ·UL94-V0 package ·no heatsink required ·1K Vdc isolation ·power density 0.85 W/cm³ ·no external component required ·low cost MODEL VBSD1-S3.3-S3.3-DIP VBSD1-S3.3-S5-DIP VBSD1-S5-S3.3-DIP VBSD1-S5-S5-DIP VBSD1-S5-S9-DIP VBSD1-S5-S12-DIP VBSD1-S5-S15-DIP VBSD1-S12-S3.3-DIP VBSD1-S12-S5-DIP VBSD1-S12-S9-DIP VBSD1-S12-S12-DIP VBSD1-S12-S15-DIP VBSD1-S15-S3.3-DIP VBSD1-S15-S5-DIP VBSD1-S15-S9-DIP VBSD1-S15-S12-DIP VBSD1-S15-S15-DIP VBSD1-S24-S3.3-DIP VBSD1-S24-S5-DIP VBSD1-S24-S9-DIP VBSD1-S24-S12-DIP VBSD1-S24-S15-DIP VBSD1-S24-S24-DIP input voltage nominal range (V dc) (V dc) output voltage (V dc) output current max. min. (mA) (mA) efficiency typ. (%) UL60950-1 3.3 3.3 5 5 5 5 5 12 12 12 12 12 15 15 15 15 15 24 24 24 24 24 24 3.00~3.60 3.00~3.60 4.5~5.5 4.5~5.5 4.5~5.5 4.5~5.5 4.5~5.5 10.8~13.2 10.8~13.2 10.8~13.2 10.8~13.2 10.8~13.2 13.5~16.5 13.5~16.5 13.5~16.5 13.5~16.5 13.5~16.5 21.6~26.4 21.6~26.4 21.6~26.4 21.6~26.4 21.6~26.4 21.6~26.4 3.3 5 3.3 5 9 12 15 3.3 5 9 12 15 3.3 5 9 12 15 3.3 5 9 12 15 24 303 200 303 200 111 83 67 303 200 111 83 67 303 200 111 83 67 303 200 111 83 67 42 31 20 30 20 12 9 7 30 20 12 9 7 31 20 12 9 7 31 20 12 9 7 4 72 74 72 70 78 78 80 72 71 76 78 79 73 74 75 79 75 76 73 78 78 79 78 NO NO NO YES YES YES YES NO YES YES YES YES NO NO NO NO NO NO YES YES YES YES NO 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 phone fax rev. page date 2 of 3 09/2008 PART NUMBER: VBSD1-DIP series DESCRIPTION: dc-dc converter O UTPUT parameter output power voltage accuracy ripple noise line regulation load regulation conditions/description refer to tolerance envelope graph @ 20 MHz bandwidth @ 20 MHz bandwidth for Vin change of 1% (3.3 V output) for Vin change of 1% (other V output) 10% to 100% full load 3.3 V 5V 12 V 9V 15 V refer to recommended circuit 100% load, nominal input min 0.1 nom max 1 75 150 1.5 1.2 20 15 15 15 15 0.03 units W mVpp mVpp % % % % % % % %/°C KHz 50 75 15 12.8 8.3 6.8 6.3 100 temperature coefficient switching frequency note: 1. All specifications measured at TA-25°C, humidity 3,500,000 hours ISOLATION SPECIFICATIONS parameter isolation voltage isolation resistance conditions/description flash tested for 1 minute test at 500 V dc min 1000 1000 nom max units V dc MΩ DIMENSIONS (mm) Side View 12.70 (0.5) Bottom View 2.54 (0.1) +0.15 0 Note: All Pins on a 2.54mm(0.1) pitch; All Pin diameters are 0.50 mm(0.02); Tolerances: ±0.25mm(0.01) Unit: mm(inch) 1 7 4 5 7 1 5 4 Pin 1 4 5 7 GND Vin + Vo 0V 1 7 4 5 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 phone fax rev. page date 3 of 3 09/2008 PART NUMBER: VBSD1-DIP series DESCRIPTION: dc-dc converter APPLICATION NOTES: - Requirement on output load To ensure this module can operate efficiently and reliably, the minimum output load should not be less than 10% of the full load. Also, this product should never be operated under no load conditions. If the actual output power is too small, please connect a resistor with proper resistance at the output end in parallel to increase the load. - Output voltage regulation and over-voltage protection circuit The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series (Figure 2). FIGURE 2 Vin GND REG +Vout DC DC 0V REG - Overload protection Under normal operating conditions, the output circuit of these products has no protection against overload. The simplest method is to connect a self-recovery fuse in series at the input end or to add a circuit breaker to the circuit. - Recommended circuit If you want to further decrease the input/output ripple, an “LC” filtering network may be connected to the input and output ends of the dc-dc converter, see (Figure 1). Vin GND +Vout DC DC 0V TYPICAL CHARACTERISTICS FIGURE 1 +Vin Cin L L +Vout Cout -Vin DC DC -Vout To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of dc-dc converter in addition to a maximum load (namely full load). During operation, make sure the specified range of input voltage is not exceeded, the minimum output load is not less than 10% of the full load, and that this product should never be operated under no load. If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, or use our company’s products with a lower rated output power. Ambient Temperature ( C ) EXTERNAL CAPACITOR TABLE Vin 3.3/5VDC 12VDC 24VDC ---External capacitor 4.7uF 2.2uF 1uF ---Vout 3.3VDC 5VDC 9VDC 12VDC 15VDC External capacitor 10uF 10uF 4.7uF 2.2uF 1uF It is not recommended to connect any external capacitor in the application field with less than a 0.5 watt output. 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 phone fax