VMS-365-12

Additional Resources: Product Page date 10/21/2018 page 1 of 5 SERIES: VMS-365 │ DESCRIPTION: AC-DC POWER SUPPLY U up to 365 W continuous power industry standard 3" x 5" footprint 18 W/in3 power density universal input (85-264 Vac / 125-373 Vdc) single output from 12 to 48 V active power correction (98%) 12 V auxiliary fan output, 5 V standby no minimum load required over load, over voltage, and short circuit protections full medical and ITE safety approvals efficiency up to 90% V DE VMS-365-12 output voltage output current (Vdc) max (A) 12 VMS-365-24 24 VMS-365-48 48 ripple and noise2 efficiency max (W) max (mVp-p) typ (%) 365 120 90 30.4 15.2 365 240 90 7.6 365 480 90 1. Total continuous output power will not exceed 365 W forced air (400 LFM), 200 W without fan 2. Measured at 20 MHz, twisted pair with 0.47 µF ceramic and 22 µF tantalum parallel capacitors O N Notes: output power1 TI MODEL N • • • • • • • • • • • ED FEATURES VMS-365 - XX Base Number Output Voltage D IS C PART NUMBER KEY cui.com Additional Resources: Product Page CUI Inc │ SERIES: VMS-365 │ DESCRIPTION: AC-DC POWER SUPPLY date 10/21/2018 │ page 2 of 5 INPUT conditions/description min voltage frequency at 90 Vac, cold start at 180 Vac, cold start inrush current no damage at 230 Vac, full load, cold start power factor measured at full load and 115 Vac/60 Hz and 230 Vac/50 Hz input source, coming impedance will be less than 0.25Ω, compliant to EN61000-3-2 for harmonic currents OUTPUT conditions/description low line to high line load regulation all other outputs 12 V aux. output 5 V SB standby 5 Vdc, 2A (400 LFM forced air) / 1A (convection) PROTECTIONS O conditions/description max units 0.98 typ ±1 % ±1 ±15 ±5 % % % 0.25 mV/°C ms min 20 ms 16.6 ms ±5 % typ automatically recovers max units 130 % 150 % max units auto recovery with no damage from a short on any output IS C short circuit protection A A TI 12 Vdc / 500 mA for external fan N fan drive over current protection 5 2.5 0.2 115 Vac /60 Hz adjustability over voltage protection Hz 500 rise time parameter 63 25% Imax to Imax , 0.1 A/µs slew rate, ±5% max. deviation, 10 ms recovery start-up time hold-up time 47 min temperature coefficient transient response Vac Vdc N parameter line regulation units 264 373 0.9 typ U current max 90 125 ED parameter SAFETY & COMPLIANCE parameter conditions/description min isolation voltage primary to secondary (for 1 second): primary to earth ground (for 1 second): safety approvals UL 60950-1/60601-1, VDE EN60950-1/EN60601-1, EMI/EMC EN55022:1998 (CISPR 22 class A conducted), EN61000-3-2: 2000, EN61000-3-3: A1:2001, EN55024 (IEC61000-4-2: 1995, IEC61000-4-3: 1995, IEC61000-4-4: 1995, IEC61000-4-5: 1995, IEC61000-4-6: 1996, IEC61000-4-11: 1994), CE measured per IEC 60950-1, paragraph 5.1, test voltage of 120 Vac/60 Hz test voltage of 230 Vac / 60 Hz MTBF with 400 LFM forced air, MIL-HDBK-217E-1, 75% of rated full load, 25°C ambient RoHS 2011/65/EU D leakage current cui.com typ 5,656 5,656 Vdc Vdc 0.110 0.275 300,000 mA mA hrs Additional Resources: Product Page CUI Inc │ SERIES: VMS-365 │ DESCRIPTION: AC-DC POWER SUPPLY date 10/21/2018 │ page 3 of 5 ENVIRONMENTAL conditions/description min operating temperature storage temperature operating humidity non-condensing max units -20 50 °C -40 80 °C 90 % 95 % 8 storage humidity vibration operating (10 ~ 300 Hz, 1 hour per axis, 3 hours total) non-operating (10 ~ 500 Hz, 1 hour per axis, 3 hours total) 10 140 G G 1 2 Grms Grms U shock operating (11 ms, half sine, for a total of 6 shock inputs) non-operating (2 ms, half sine, for a total of 6 shock inputs) typ ED parameter DERATING CURVES N output power vs. ambient temperature TI 2 80 60 54 1 40 20 4 -20 0 N Load (%) 100 10 20 30 40 50 60 1 Convection 2 Forced air (400 LFM) 70 O Ambient Temperature (°C) APPLICATION NOTES D IS C 1. P/S ON Logic Table Negative Logic SW Closed (VPSON 2.5 Vor Open Circuit Output off cui.com Additional Resources: Product Page CUI Inc │ SERIES: VMS-365 │ DESCRIPTION: AC-DC POWER SUPPLY date 10/21/2018 │ page 4 of 5 2. Power OK POWER OK SIGNAL CHARACTERISTICS +5 V TTL Compatible Logic Level Low < 0.4 V while Sinking a maximum of 10 mA Logic Level High Between 2.4 V and 5 V Output while Sourcing 200 μA High State Output Impedance 1 K Pull-Up from +5 Vsb to Termination Point Max. Low Level Surge Current 56 mA for 5μS with a 500 mS on/150 mS off duty cycle U Signal Type Ø4.04[Ø0.159] MOUNTING HOLE TYP 4 PLCS A 64.80 2.551 CN1 1 AC Line 2 AC Neutral INPUT SPADE CONNECTOR Gnd 76.40 3.008 2 J1 MOLEX (26-60-4030) 3 PIN, CTR PIN REMOVED 0.156" SPACING QUICK DISCONNECT TAB 6.35[0.250] X 0.81[0.032] MOLEX (19705-4301) IS C 29.60 1.17 35.65 1.40 MAX 4.40 0.17 MAX SMT COMPONENT HEIGHT J3 8 7 6 5 4 3 2 1 7 8 9 10 11 12 DETAIL A SCALE 1 : 1 cui.com 1 V1 2 V1 3 V1 4 V1 5 V1 6 V1 7 DC Returns 8 DC Returns 9 DC Returns 10 DC Returns 11 DC Returns 12 DC Returns CN3 1 2 3 4 5 6 J2 AC Ground CN2 1 O Ø6.35[Ø0.250] MAX DIA OF MOUNTING HARDWARE TYP 4 PLCS 115.60 4.551 TI MOLEX (39-28-1123) MINIFIT JR., VERTICAL DUAL ROW CONNECTOR, 12 PIN 0.165" PITCH MATING CONNECTOR: MOLEX (39-01-2120) 127.00 5.000 N MOLEX (90130-1108) C-GRID III SHROUDED HEADER VERTICAL, DUAL ROW, 8 PIN 0.10" PITCH MATING CONNECTOR: MOLEX (90142-0008) N MECHANICAL DRAWING D ED The POK pin of CN3 shall change from STATE (4.5V) 100-500 ms after the main outputs are within the regulation limits. Conversely, the POK should be de-asserted to a low srare when any of the main output voltages fall below its under-voltage threshold, or when the main power has been removed for a time sufficiently long such that the power supply operation cannot be guaranteed beyond the power-down warning time. The power down warning time must be 1mS minimum. The electrical characteristics for the Power OK output driver are shown below. 1 +5V Aux 2 FAN- 3 RS+ 4 FAN+ 5 P OK 6 PS ON 7 RS- 8 -5V Aux GND Additional Resources: Product Page CUI Inc │ SERIES: VMS-365 │ DESCRIPTION: AC-DC POWER SUPPLY date 10/21/2018 │ page 5 of 5 REVISION HISTORY description date 05/13/2011 1.0 initial release 1.01 new template applied 1.02 V-Infinity branding removed 1.03 updated drawing 1.04 added CCC safety approval 1.05 removed CCC safety approval ED rev. 08/01/2011 08/22/2012 04/18/2013 12/16/2013 10/21/2018 D IS C O N TI N U The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 Fax 503.612.2383 cui.com techsupport@cui.com CUI offers a two (2) year limited warranty. Complete warranty information is listed on our website. CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.