1/5
VPM-S800-XXR(I)-N Switching Power Supply
Rev. 04-2007
Features
·Universal AC Input / Full Range ·Built-in active PFC function ·Short Circuit, overload, over voltage, over temperature protected ·Current Sharing (Available) ·Current Monitoring ·Power Good Signal ·Built-in Remote Inhibit ·Built-in Remote Sense ·Extended temperature range: -40 ~ +75 ºC available
Model 1 VPM-S800-12R(I)-N VPM-S800-15R(I)-N VPM-S800-24R(I)-N VPM-S800-36R(I)-N VPM-S800-40R(I)-N VPM-S800-48R(I)-N
Preset Voltage 12V 15V 24V 36V 40V 48V
Output Current Output 2, 3, 4 12 15 20 27 37 14 19 26 36 47 V V V V V Minimum 0A 0A 0A 0A 0A 0A Maximum 62.5 A 50 A 40 A 29.63 A 21.62 A 16.67 A
Ripple & Noise 7, 8 Max. Power 5, 6 Regulation 7 750 W +/- 1% 750 W +/- 1% 800 W +/- 1% 800 W +/- 1% 800 W +/- 1% 800 W +/- 1% (Vpp) 1% 1% 1% 1% 1% 1%
48 - 60 V
Notes:
1 2 3 4 Adding “I” Indicates Current sharing model. Customer must specify output voltage. Output is fully isolated. Output voltage is measured at output power connector.
5 Provides peak power of 900 W within 500 µS for all models. For longer duty duration please contact us. 6 Must use external forced airflow min. 30 CFM to achieve maximum power. 7 1% minimum load is required to maintain the ripple and regulation. 8 Ripple and noise is measured from 10 KHz to 20 MHz at output terminals with a 0.1 µF ceramic capacitor and a 22 µF electrolytic capacitor in parallel.
V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062
www.v-infinity.com
1-866-372-1258
2/5
VPM-S800-XXR(I)-N Switching Power Supply
Rev. 04-2007
Input
Parameter Input Frequency Input Voltage Input Current Inrush Current Power Factor Conditions/Description Min 47 90 At 90-264 VAC Peak measured at 230 VAC at full load, cold start Active power factor correction meets EN61000-3-2 class D Nom Max 63 264 12 70 Units Hz VAC A A
Output
Parameter Transient response Conditions/Description Min Nom Max Units Output voltage returns to within 1% in less than 2.5 mS for a 50% load change. Peak t ransient does not exceed 5%. Turn-on and turn-off overshoot shall not exceed 5 % over nominal voltage. Measured at 230 V and full load 12 V model: 80% All other models: 83% At 120 VAC 1 second 80% of rated maximim load 20 mS Adjustable with built-in trim pot. +/- 5% Designated as RS+ and RS- on the CN3. Total voltage compensation for cable losses with respect to the main output. (NOT available for current sharing models.) Designated as RSW on the CN3. Requires a low signal to inhibit the output. Green - the power supply is operating normally. Orange - when any protection occurs or when Remote Inhibit is in effect. Designated as PG on the CN3. This signal goes high 100-500 mS after the output reaches regulation. I t goes low at least 1 mS before loss of regulation. Designated as CSH on (CN3), use in parallel for forced current sharing function. Accuracy of shared current with up to 4 parallel units is within 10% at full load. Disignated as CMN on (CN3) for current sense purpose. CMN is a 0.5 to 3VDC output voltage to represent a linear 0% to 100% output current.
Overshoot Efficiency
Turn on delay Hold up time Adjustability Remote sense Remote Inhibit LED display (LED 1) Power Good
Current Sharing Current Monitor
Protection Circuit
Parameter Input Fuse Input under-voltage Conditions/Description Built-in ac fuse. A blown fuse usually indicates permanent damage to the power supply serviceable by factory only. Power supply shuts down when ac input is under 80 VAC. When ac line reappears over 86 +/- 5 VAC, t he power supply restarts automatically. Overload Short circuit Output Over-voltage Current limiting starts at 110-140% of the rated output current and recovers automatically. Short circuit can be continuous. Recovers automatically upon removal of short. Output is protected agaist overvoltage. Unit shuts down and latches when voltage at output terminals exceeds 130%. AC input needs to be r eset to restart the power supply. Over temp. Power supply shuts down when temperature is in excess of 85 ºC. Auto recovery.
V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062
www.v-infinity.com
1-866-372-1258
3/5
VPM-S800-XXR(I)-N Switching Power Supply
Rev. 04-2007
General and Safety
Parameter Operating temp. Optional operating temp. Storage temp. Optional storage temp. Operating humid. Storage humid. EMI Safety Conditions/Description Derates linearly from 100% load at 50 ºC to 50% load at 70 ºC. Derates linearly from 100% load at 50 ºC to 37.5% load at 75 ºC. -20 -40 85 85 ºC ºC Min 0 -40 Nom Max 50 75 Units ºC ºC
Non-condensing 5% 90% RH Non-condensing 5% 95% RH FCC Part 15, CISPR 22 class B, Conducted UL60950-1 (E222889), CSA C22.2 No. 60950-1-03, TUV EN60950-1, CE Mark(LVD) E N61000-3-2,3 & IEC61000-4 series regulations and CB. Leakage Current at 240 VAC 3.5 mA Isolation Voltage Applied for 3 seconds (HI-POT) Primary to secondary: 3000 VAC Primary to transformer core: 1500 VAC Primary to earth ground: 1500 VAC Grounding Test Allowable resistance measured when 25 A current is 0.1 Ohm applied from the ground pin of the three prong plug t o the farthest earthed connection point. Warranty Standard warranty length 2 years MTBF According to MIL-HDBK-217 at 30 ºC 150,000 hours Burn-in Full load, at 45 +/- 5 ºC, 230 VAC. Burn-in for 1 8 hours up to 8 hours in early productions. Time reduced gradually as product matures. Note : Customer must specify extended temperature on PO.
Mechanical
P arameter Weight Enclosure Mounting holes Conditions/Description Min Nom Max 1450 9.17(L) x 4.25(W) x 2.5(H) Two sets of 8 threaded mounting holes available on the enclosure B: 6-32, maximum insertion depth of 0.2 inches. C: M4, maximum insertion depth of 0.2 inches. Units grams inches
Input Connector - (CN1)
P arameter AC input (Option 1) AC Input (Option 2) Conditions/Description IEC320 or equivalent Suggested mating plug: IEC320 or equivalent DINKLE Terminal block Part No. DT-35-A02W-03 (3 pin), M3 x 8.25mm centering
Note :
Suggested mating connector: M olex 19198-0045 or similar Input connector needs to be specified on the PO.
V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062
www.v-infinity.com
1-866-372-1258
4/5
VPM-S800-XXR(I)-N Switching Power Supply
Rev. 04-2007
Output Connector - (CN2)
Parameter Output (Option 1) Conditions/Description Molex Part No. 26-48-1201 or similar.(20 pin) Output pin assignment, VO+ (Pins 1-10), VO- (Pins 11-20) Suggested mating connector: M olex Part No. 09-91-2000, contact:08-50-0106 or similar. Output (Option 2) Howder Terminal block Part No. HD-121-8P (8 pin, M3.5 Screw) 9.5mm spacing Output pin assignment, VO+ (Pins 1-4), VO- (Pins 5-8)
Note:
Suggested mating connector: M olex 19198-0045 or similar. Output connector needs to be specified on the PO.
Logic Connector - (CN3)
Parameter Logic Pin Assignments: Conditions/Description JS B7B-XH-A Suggested mating connector: J ST XHP-7 or equivalent , Contact: SXH-001T-P0.6. 1. CMN - Current Monitoring 2. CSH - Current Sharing 3. RTN - Return / Output Ground 4. PG - Power Good Signal 5. RSW - (Remote On-Off / Remote Inhibit) 6. RS(-) - Remote Sense 7. RS(+) - Remote Sense JST B2B-XH-A Suggested mating connector: J ST XHP-2 or equivalent, Contact: SXH-001T-P0.6.
Fan
V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062
www.v-infinity.com
1-866-372-1258
5/5
VPM-S800-XXR(I)-N Switching Power Supply
Rev. 04-2007
VO+
VO+
V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062
LN
CN1
B B
C
B
B
C
C C B
C
C C
B
C
B
CN2
FAN
B
VO-
VO-
www.v-infinity.com
1-866-372-1258
