VWQAS2-Q48-D15-SIP

1/3 VWQAS2-SIP Series DC-DC Converter Rev. 07-2007 Description Designed to convert a wide input voltage range into an isolated regulated voltage, the VWQAS2-SIP series is well suited for providing board-mount local supplies in a wide range of applications, including mixed analog/digital circuits, test & measurement equip., process/machine controls, datacom/telecom fields, etc... Features ·Ultrawide (4:1) input range ·High efficiency to 82% ·Regulated ·Dual voltage output ·I/O Isolation 1500VDC ·No heatsink required ·Short circuit protection ·Remote on/off ·MTBF >1,000,000 hrs ·Temperature range: -40°C~+85°C Model Number Nominal VWQAS2-Q24-D5-SIP 24 Vdc VWQAS2-Q24-D9-SIP 24 Vdc VWQAS2-Q24-D12-SIP 24 Vdc VWQAS2-Q24-D15-SIP 24 Vdc VWQAS2-Q48-D5-SIP 48 Vdc VWQAS2-Q48-D9-SIP 48 Vdc VWQAS2-Q48-D12-SIP 48 Vdc VWQAS2-Q48-D15-SIP 48 Vdc Input Voltage Range 9.0~36.0 Vdc 9.0~36.0 Vdc 9.0~36.0 Vdc 9.0~36.0 Vdc 18.0~72.0 Vdc 18.0~72.0 Vdc 18.0~72.0 Vdc 18.0~72.0 Vdc Max. 40 Vdc 40 Vdc 40 Vdc 40 Vdc 80 Vdc 80 Vdc 80 Vdc 80 Vdc Output Voltage ±5 Vdc ±9 Vdc ±12 Vdc ±15 Vdc ±5 Vdc ±9 Vdc ±12 Vdc ±15 Vdc Output Current Max. Min. ±200 mA ±0 mA ±111 mA ±0 mA ±83 mA ±0 mA ±67 mA ±0 mA ±200 mA ±0 mA ±111 mA ±0 mA ±83 mA ±0 mA ±67 mA ±0 mA Efficiency 76% 78% 82% 81% 75% 77% 81% 80% Package Style SIP SIP SIP SIP SIP SIP SIP SIP Note: 1. All specifications measured at TA=25°C, humidity 1,000,000 hrs. 7g Isolation Specifications Item Isolation Voltage Isolation Resistance Isolation Capacitance Test Conditions Flash tested for 1 min. Test at 500 Vdc Input/Output Min. 1500 1000 Typ. Max. Units Vdc MΩ PF 80 Typical Characteristics Vc Vin Li n Cou t 7 C1 C2 1 8 Cou t Ic R 2 3 6 R= Vc/Ic -0.15 ( 5 mA TY P) R:KΩ +Vo 0V GND -V o O utline Dimensions & Recommended Layout Pattern 26. 00 [ 1. 024] 0. 30 [ 0. 012] 12. 50 [ 0. 492] 4. 00 [ 0. 157] 2. 00 [ 0. 079] 7. 62 [ 0. 300] 2. 54 [ 0. 100] 3. 68 [ 0. 145] 2. 90 [ 0. 114] date 0. 50 [ 0. 020] Pin 1 2 3 6 7 0V 8 NC 9 -Vo Fu nctio n GN D V in C TRL +Vo Note: Tolerances : (pin: ± 0.1(0.004); others: ±0.25(0.01)) V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062 www.v-infinity.com 1-866-372-1258 0. 50 [ 0. 020] 123 6789 9. 50 [ 0. 374] Bottom View 3/3 VWQAS2-SIP Series DC-DC Converter Rev. 07-2007 Application Notes: - All of the VWQAS2-SIP Series have been tested according to the following recommended testing circuit before leaving the factory. This series should be tested under load(Figure 1). If you want to further decrease the input/output ripple, you can increase capacitance properly or choose capacitors with low ESR. However, the capacitance should not be too high(Table 2). - Input current Nominal input voltage range. The input current of the power supply must be sufficient to the startup current (Ip) of the DC/DC module (Figure 2) Input Current(A) Ip Table 2 Vout ±5 ±9 ±12 ±15 Cout (Max) ±330μF ±220μF ±150μF ±120μF Input Voltage Range Input Voltage (V ) - Output Load In order to ensure the product operates efficiently and reliably, make sure the specified range of input voltage is not exceeded. No parallel connection or plug and play. Figure 1 Temperature Derating Graph Operating Temp.( C ) - NC Terminals Unless otherwise specified, NC terminals of all series are used for converter's interior circuit connection, and are not allowed connection of any external circuit.; - CTRL Terminal When open or high impedance, the converter will work well; When this pin is ‘high’; the converter will shutdown; It should be noted that the input current should remain between 5-10mA,exceeding the maximum 20mA will cause permanent damage to the converter. V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062 www.v-infinity.com 1-866-372-1258