CDMG13008L-02

Part No: CDMG13008L-02 Description: micro dynamic speaker Date: 10/18/2006 Unit: mm Page No: 1 of 6 Specifications Dimensions Impedance Resonant frequency Sound pressure level Response Distortion Input power Operation Buzz, rattle, etc. Magnet Operating temp. Weight Material RoHS ø13.0 x 2.0 mm 8 Ohm ± 15% at 1.5 KHz 1 V 1050 Hz ± 20% at 1V 86 dB/w ± 3 dB 0.2 w 10 cm at 1.5K, 2.0K, 2.5K, 3.0K Hz 75 dB/w ± 3 dB 1 w 1m at 1.5K, 2.0K, 2.5K, 3.0K Hz Fo Hz ~ 20 KHz max. 10% max. at 1.5 KHz 0.2W Nominal 0.2 W Handling capacity 0.4 W must be normal at program source 0.2 W must be normal at sine wave 1.26 V ø7.0 x 0.7 (Nd-Fe-B) -20 ~ +55°C 0.7 g Metal yes Mechanical Drawing Tolerance: ±0.3 Week 01 02 . . Year 05---2005 06---2006 . . 2.0 1.0 13.0 9.0 SOLDERING POINT BLACK POLYESTER Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CDMG13008L-02 Description: micro dynamic speaker Date: 10/18/2006 Unit: mm Page No: 2 of 6 Frequency Response Curve Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CDMG13008L-02 Description: micro dynamic speaker Date: 10/18/2006 Unit: mm Page No: 3 of 6 Measurement Circuit Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CDMG13008L-02 Description: micro dynamic speaker Date: 10/18/2006 Unit: mm Page No: 4 of 6 Mechanical Characteristics Item PCB Wire Pull Strength Evaluation Standard Test Condition The pull force should be applied to double lead No damage or cutting off. wire: Horizontal 3.0N (0.306kg) for 30 seconds The speaker should be measured after applying No obstacle will be harmful to a vibration amplitude of 1.5 mm with 10 to normal operation; damage, 55 Hz band of vibration frequency to each of cracks, rust, and distortions. the 3 perpendicular directions for 2 hours. Should not be audible at 1.26 V The part will be dropped, contained inside a sine wave between Fo ~ 20 KHz. normal box, from a height of 75 cm onto a 40 mm thick wooden board 10 times. Vibration Drop Test Environment Test Item High temp. test Low temp. test Humidity test Temp. cycle test Test Condition After being placed in a chamber at 55°C for 96 hours. After being placed in a chamber at -20°C for 96 hours. After being placed in a chamber at +40°C and 90% relative humidity for 240 hours. The part shall be subjected to 5 cycles. One cycle will consist of: Evaluation Standard The speaker will be measured after being placed at +25°C for 6 hours. No obstacle will be harm ful to normal operation; damage, cracks, rust, and distortions. Should not be audible at 1.26 V sine wave between Fo ~ 20 KHz. The SPL should be within ±3dB compared to the initial measurements. Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CDMG13008L-02 Description: micro dynamic speaker Date: 10/18/2006 Unit: mm Page No: 5 of 6 Reliability Test Item Load Test Test Condition 0.2 W white noise, applied for 96 hours, at room temperature. Evaluation Standard The speaker will be measured after being placed at +25°C for 6 hours. No obstacle will be harm ful to normal operation; damage, cracks, rust, and distortions. Should not be audible at 1.26 V sine wave between Fo ~ 20 KHz. The SPL should be within ±3dB compared to the initial measurements. Test Conditions Standard Test Condition Judgement Test Condition a) Tempurature: +5 ~ +35°C a) Tempurature: +25 ±2°C b) Humidity: 45 - 85% b) Humidity: 60 - 70% c) Pressure: 860-1060 mbar c) Pressure: 860-1060 mbar Recommended Temperature Profile for Hand Soldering Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062 Part No: CDMG13008L-02 Description: micro dynamic speaker Date: 10/18/2006 Unit: mm Page No: 6 of 6 Packaging Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062