PBK-5-24-B

Additional Resources: Product Page date 06/07/2016 page 1 of 7 SERIES: PBK-5 │ DESCRIPTION: AC-DC POWER SUPPLY up to 5 W continuous output ultra compact SIP package universal input voltage: (85~264 Vac / 100~400 Vdc) single regulated outputs from 3.3~24 Vdc 3,000 Vac isolation over current, short circuit, and over voltage protections UL 60950-1 safety approval efficiency up to 75% output voltage output current output power ripple and noise1 efficiency (Vdc) max (A) max (W) max (mVp-p) typ (%) 1 3.3 150 65 PBK-5-3 3.3 PBK-5-5 5 PBK-5-9 9 12 PBK-5-15 PBK-5-24 5 120 70 5 120 72 0.42 5 120 74 15 0.34 5 120 75 24 0.21 5 150 75 1. Measured at 20 MHz bandwidth, see Test Configuration section. O Note: 1 0.56 N PBK-5-12 TI MODEL N U • • • • • • • • ED FEATURES PBK-5- XX - X Base Number Output Voltage D IS C PART NUMBER KEY cui.com Orientation “blank” = vertical B = right-angle Additional Resources: Product Page CUI Inc │ SERIES: PBK-5 │ DESCRIPTION: AC-DC POWER SUPPLY date 06/07/2016 │ page 2 of 7 INPUT conditions/description min voltage frequency current at 115 Vac at 230 Vac inrush current at 115 Vac at 230 Vac leakage current CY0 is 1nF/400Vac max units 85 100 264 400 Vac Vdc 47 440 Hz 200 100 mA mA 20 30 no load power consumption 1 A/250 V, slow-blow type (external, recommended) U input fuse OUTPUT parameter conditions/description min line regulation at full load load regulation at 10%~100% load PBK-5-3 all other models N at 115 Vac at 230 Vac switching frequency parameter short circuit protection conditions/description over voltage protection 0.25 mA 0.5 W max units % 2200 1500 680 470 330 100 μF μF μF μF μF μF ±0.1 ±0.5 % ±1.0 ±1.5 % ±2 ±3 % ±1 ±2 20 80 min % ms ms 100 kHz ±0.02 %/°C typ max units continuous, auto restart auto restart 110 IS C over current protection O temperature coefficient PROTECTIONS TI capacitive load 3.3 Vdc output models 5 Vdc output models 9 Vdc output models 12 Vdc output models 15 Vdc output models 24 Vdc output models hold-up time typ A A 10 N output current voltage set accuracy typ ED parameter % zener diode clamp SAFETY & COMPLIANCE parameter conditions/description isolation voltage input to output for 1 minute at 5mA min isolation resistance typ max Vac 100 MΩ UL 60950-1 safety standards UL 60950-1 safety class class II conducted emissions CISPR22/EN55022 external circuit required, Class A (see figure 2); Class B (see figure 3) radiated emissions CISPR22/EN55022 external circuit required, Class B (see figures 2 or 3) ESD IEC/EN61000-4-2 Class B, contact ±4 kV D safety approvals radiated immunity EFT/burst IEC/EN61000-4-3 Class A, 10V/m IEC/EN61000-4-4 Class B, ±2 kV (external circuit required, see figure 2) IEC/EN61000-4-4 Class B, ±4 kV (external circuit required, see figure 3) cui.com units 3,000 Additional Resources: Product Page CUI Inc │ SERIES: PBK-5 │ DESCRIPTION: AC-DC POWER SUPPLY date 06/07/2016 │ page 3 of 7 SAFETY & COMPLIANCE (CONTINUED) conditions/description IEC/EN61000-4-5 Class B, ±1 kV/±2 kV (external circuit required, see figure 3) min conducted immunity IEC/EN61000-4-6 Class A, 3 Vr.m.s (external circuit required, see figure 3) PFM IEC/EN61000-4-8 Class A, 10 A/m voltage dips & interruptions IEC/EN61000-4-11 Class B, 0%-70% MTBF at 25°C, max. load RoHS 2011/65/EU conditions/description min operating temperature see derating curves -25 storage temperature case temperature N non-condensing DERATING CURVES Safe operating area 60 Safe operating area 40 -5 0 5 55 65 75 95 85 95 105 110 115 235 240 245 O efficiency vs. load PBK-5-12   110 VAC   240 VAC IS C  120 VAC 220 VAC 230 VAC  264 VAC         255 °C 85 % ~ ~ 100 80 60 Safe operating area 40 20 100 264 135 320 efficiency vs. input voltage (Vac)  PBK-5-3  PBK-5-5  PBK-5-9  PBK-5-12 PBK-5-15  PBK-5-24            Input Voltage (VAC) efficiency vs. load PBK-5-12 efficiency vs. input voltage (Vdc)  100 VDC 200 VDC D  Efficency (%) 100     300 VDC 400 VDC    PBK-5-3  PBK-5-5      PBK-5-9 PBK-5-12 PBK-5-15    °C Input Voltage (Vdc) Load (%)  °C    85 105  85 VAC   125 units load vs. input voltage (Vdc) (at 25°C) Input Voltage (Vac) EFFICIENCY CURVES Efficency (%) 85 max ~ ~ ~ ~ 45 Ambient Temperature (°C) Efficiency (%) -15 N 20 ~ ~ 20 80 Load (%) 60 ~ ~ ~ ~ 100 80 Load (%) Load (%) load vs. input voltage (Vac) (at 25°C) TI load vs. ambient temperature (at 110~240 Vac input voltage) -25 typ -40 humidity PBK-5-24        Load (%)   units hours U parameter 40 max 300,000 ENVIRONMENTAL 100 typ ED parameter surge         Input Voltage (VDC) cui.com   353 Additional Resources: Product Page CUI Inc │ SERIES: PBK-5 │ DESCRIPTION: AC-DC POWER SUPPLY date 06/07/2016 │ page 4 of 7 SOLDERABILITY conditions/description min typ max units for 3~5 seconds 350 360 370 °C wave soldering for 5~10 seconds 255 260 265 °C parameter conditions/description min dimensions vertical models: 42 x 11 x 27 right-angle models: 42 x 25 x 13 material UL94V-0 MECHANICAL ED parameter hand soldering typ 10 U MECHANICAL DRAWING VERTICAL ORIENTATION N PIN CONNECTIONS -Vin (N) 3 +Vin (L) 5 +V(CAP) 7 -V(CAP) 12 -Vo 14 +Vo O Note: 1. It is required to add C1 between pins 5 & 7 (see application circuits). TI FUNCTION 1 N PIN Front View IS C D units mm mm weight units: mm[inch] tolerance: ±0.5[±0.020] pin tolerance: ±0.1[±0.004] max Top View PCB Layout Bottom View cui.com g Additional Resources: Product Page CUI Inc │ SERIES: PBK-5 │ DESCRIPTION: AC-DC POWER SUPPLY date 06/07/2016 │ page 5 of 7 MECHANICAL DRAWING (CONTINUED) RIGHT-ANGLE ORIENTATION ED units: mm[inch] tolerance: ±0.5[±0.020] pin tolerance: ±0.1[±0.004] FUNCTION 1 -Vin (N) 3 +Vin (L) 5 +V(CAP) 7 -V(CAP) 12 -Vo 14 +Vo U PIN CONNECTIONS PIN Front View Side View N TI N Note: 1. It is required to add C1 between pins 5 & 7 (see application circuits). Bottom View O Top View PCB Layout IS C TEST CONFIGURATION Table 1 Recommended External Circuit Components C on n e c t Os c illo g r ap h Pro b e C o pp e r s h e e t $&/ Figure 1 F U SE C1 D $&1 +Vo  L1   C2 AC -D C    -Vo C Y0 C3 C4 L oa d VOUT (Vdc) C11 C21 L11 C31 C4 CY0 (Y1 capacitor) 3.3 22μF/400V 470μF/10V 0.47μH 150μF/35V 100nF/50V 1nF/400Vac 5 22μF/400V 470μF/16V 0.47μH 150μF/35V 100nF/50V 1nF/400Vac 9 22μF/400V 330μF/25V 1μH 150μF/35V 100nF/50V 1nF/400Vac 12 22μF/400V 330μF/25V 1μH 150μF/35V 100nF/50V 1nF/400Vac 15 22μF/400V 330μF/25V 1μH 150μF/35V 100nF/50V 1nF/400Vac 24 22μF/400V 100μF/35V 4.7μH 47μF/35V 100nF/50V 1nF/400Vac Note: 1. Required components. 2. 1 A/250 V fuse required. cui.com Additional Resources: Product Page CUI Inc │ SERIES: PBK-5 │ DESCRIPTION: AC-DC POWER SUPPLY date 06/07/2016 │ page 6 of 7 TYPICAL APPLICATION CIRCUIT 1 7& Figure 2 MOV CX 1 C1 + 7 1 C3 T VS C4 RL + 5 AC -D C A C( N) L1 +V o C2 14 3 ED ) 86 ( AC( L ) + 12 -Vo  Note: (1) is Pi filter circuit. C Y0 U Table 2 Recommended external circuit components VOUT (Vdc) C11 C21 L11 C31 C4 CX1 3.3 22μF/400V 470μF/10V 0.47μH 150μF/35V 100nF/50V 0.1µF/275Vac 5 22μF/400V 470μF/16V 0.47μH 150μF/35V 100nF/50V 0.1µF/275Vac 1nF/400Vac 9 22μF/400V 330μF/25V 1μH 150μF/35V 100nF/50V 0.1µF/275Vac 1nF/400Vac 12 22μF/400V 330μF/25V 1μH 150μF/35V 100nF/50V 0.1µF/275Vac 15 22μF/400V 330μF/25V 1μH 150μF/35V 100nF/50V 0.1µF/275Vac 24 22μF/400V 100μF/35V 4.7μH 47μF/35V 100nF/50V 0.1µF/275Vac 1. Required components. AC(L) FUSE LDM LCM CY2 C1 + O IS C D 1. 2. 3. 4. 5. 6. 7. 8. 9. TVS 1nF/400Vac 1A/250V 5D-9 S14K350 SMBJ7.0A 1A/250V 5D-9 S14K350 SMBJ7.0A 1A/250V 5D-9 S14K350 SMBJ12A 1nF/400Vac 1A/250V 5D-9 S14K350 SMBJ20A 1nF/400Vac 1A/250V 5D-9 S14K350 SMBJ20A 1nF/400Vac 1A/250V 5D-9 S14K350 SMBJ30A 5 L1 TVS 14 +Vo CY1 + AC-DC 7 C2 + C4 RL C3 -Vo 12 AC(N) AC(N) Notes: MOV AC(L) CX Figure 3 NTC N N EMC RECOMMENDED CIRCUIT FUSE TI Note: CY0 CY0 Table 3 Recommended External Circuit Components MOV2 S10K300 CY1, CY2 1nF/400Vac CX 0.1μF/275Vac LCM 3.5mH LDM 5mH FUSE 1A/250V Note: 1. Also refer to Table 2. C1, C2, and C3 are electrolytic capacitors. They are required for both AC input and DC input. For AC input, C1 is used as a filter capacitor. The recommended C1 value is 22 μF/400 V. For DC input, C1 is used as an EMC filter capacitor. The recommended C1 value is 10μF/400V. When the input voltage is above 370VDC, we recommend a 10μF/450V capacitor. C2 and C3 are output filer capacitors, we recommend high frequency and low impedance electrolytic capacitors. For capacitance and rated ripple current of capacitors refer to the datasheets provided by the manufacturers, voltage derating of capacitors should be 80% or above. C4 is a ceramic capacitor which is used to filter high frequency noise. C2, C3 and L1 form a pi-type filter circuit. For the current of L1, refer to the datasheets provided by the manufacturers, current derating should be 80% or above. TVS is a recommended component to protect post-circuits (if converter fails). For standard EMC requirements, please refer to figure 2. If a higher EMC is required, please refer to figure 3. All specifications measured at Ta=25C, humidity