PQA30-D48-S5-D

Additional Resources: Product Page date 08/24/2021 page 1 of 7 SERIES: PQA30-D Ϳ DESCRIPTION: DC-DC CONVERTER FEATURES input voltage output voltage W\S (Vdc) range (Vdc) PQA30-D24-S3-D 24 18~36 PQA30-D24-S5-D 24 18~36 PQA30-D24-S9-D 24 18~36 24 18~36 24 18~36 output current output power ripple and noise1 HϒFLHQF\ min (A) max (A) max (W) max (mVp-p) W\S (%) 3.3 0.60 6 20 120 87 5 0.60 6 30 120 88 9 0.333 3.333 30 120 88 12 0.25 2.5 30 120 88 15 0.20 2 30 120 89 SC ON PQA30-D24-S12-D PQA30-D24-S15-D (Vdc) NU MODEL ED up to 30 W isolated output 2:1 input range (18~36 Vdc, 36~75 Vdc) smaller package single, regulated output 1,500 Vdc isolation short circuit, over current, and over voltage protections remote on/off operating temperature range (-40~85°C) six sided metal shielding efficiency up to 89% EN 62368-1 TI • • • • • • • • • • • PQA30-D24-S24-D 24 18~36 24 0.125 1.25 30 120 89 PQA30-D48-S3-D 48 36~75 3.3 0.60 6 20 120 87 PQA30-D48-S5-D 48 36~75 5 0.60 6 30 120 88 PQA30-D48-S12-D 48 36~75 12 0.25 2.5 30 120 89 PQA30-D48-S15-D 48 36~75 15 0.20 2 30 120 89 PQA30-D48-S24-D 48 36~75 24 0.125 1.25 30 120 88 Notes: 1. Ripple and noise are measured at 20 MHz BW by “parallel cable” method with 1 µF ceramic and 10 µF electrolytic capacitors on the output. DI PART NUMBER KEY PQA30 - DXX - SXX - DX Base Number Input Voltage Output Voltage Notes: *Discontinued heatsink versions. cui.com Packaging Style DIP Heatsink* "blank" = no heatsink H = with heatsink Additional Resources: Product Page CUI Inc Ϳ SERIES: PQA30-D Ϳ DESCRIPTION: DC-DC CONVERTER date 08/24/2021 Ϳ page 2 of 7 INPUT conditions/description operating input voltage 24 Vdc input models 48 Vdc input models start-up voltage 24 Vdc input models 48 Vdc input models under voltage shutdown 24 Vdc input models 48 Vdc input models surge voltage for maximum of 1 second 24 Vdc input models 48 Vdc input models start-up time nominal input, constant load min W\S max units 18 36 24 48 36 75 Vdc Vdc 17.8 35.8 18 36 Vdc Vdc 16 32 Vdc Vdc UE D parameter -0.7 -0.7 50 100 Vdc Vdc 10 ms 1 mA models ON (CTRL open or connect TTL high level, 2.5~12 Vdc) CTRL1 models OFF (CTRL connect GND or low level, 0~1.2 Vdc) ¿OWHU SL¿OWHU input current (models OFF) 1. CTRL pin voltage is referenced to GND. OUTPUT parameter conditions/description line regulation load regulation IN Note W\S max units full load, input voltage from low to high ±0.2 ±0.5 % 10% to 100% load ±0.5 ±1 % ±1 ±3 % DI SC ON T voltage accuracy min adjustability ±10 % switching frequency PWM mode 300 transient recovery time 25% load step change 300 500 kHz transient response deviation 25% load step change ±3 ±5 WHPSHUDWXUHFRHϒFLHQW 100% load ±0.02 NjV % %/°C PROTECTIONS parameter conditions/description short circuit protection hiccup, automatic recovery over current protection over voltage protection 3.3 Vdc output models 5 Vdc output models 9 Vdc output models 12 Vdc output models 15 Vdc output models 24 Vdc output models cui.com min 120 W\S max 130 150 3.96 6 10.8 15 18 28 units % Vdc Vdc Vdc Vdc Vdc Vdc Additional Resources: Product Page CUI Inc Ϳ SERIES: PQA30-D Ϳ DESCRIPTION: DC-DC CONVERTER date 08/24/2021 Ϳ page 3 of 7 SAFETY AND COMPLIANCE parameter conditions/description isolation voltage input to output for 1 minute at 1 mA max. 1,500 min W\S max units Vdc 1,000 0Ÿ input to output at 500 Vdc FHUWL¿HGWR(1 conducted emissions CISPR22/EN55022 class A (no circuit required); class B (external circuit required, see Figure 1-b) radiated emissions CISPR22/EN55022 class A (no circuit required); class B (external circuit required, see Figure 1-b) ESD IEC/EN61000-4-2 class B, contact ± 4kV radiated immunity IEC/EN61000-4-3 class A, 10V/m EFT/burst IEC/EN61000-4-4 class B, ± 2kV (external circuit required, see Figure 1-a) surge IEC/EN61000-4-5 class B, ± 2kV (external circuit required, see Figure 1-a) conducted immunity IEC/EN61000-4-6 class A, 3 Vr.m.s voltage dips & interruptions IEC/EN61000-4-29 class B, 0%-70% MTBF as per MIL-HDBK-217F @ 25°C RoHS 2011/65/EU NU Note 1,000,000 1. CE mark is only on models without heatsink. ENVIRONMENTAL conditions/description see derating curves storage temperature min non-condensing case temperature at full load, operating temperature curve range DI SC ON storage humidity vibration W\S hours max units -40 85 °C -55 125 °C 5 95 % 105 °C 10 G TI parameter operating temperature ED isolation resistance safety approvals1 10~55Hz, 30 min. along x, y, and z axis SOLDERABILITY parameter conditions/description max units hand soldering 1.5 mm from case for 10 seconds min W\S 300 °C wave soldering VHHZDYHVROGHULQJSUR¿OH 260 °C max units MECHANICAL parameter conditions/description dimensions board mount: 50.80 x 25.40 x 11.80 board mount with heatsink: 50.80 x 25.40 x 16.30 min case material aluminum alloy weight board mount board mount with heatsink W\S mm mm 22 35 cui.com g g Additional Resources: Product Page CUI Inc Ϳ SERIES: PQA30-D Ϳ DESCRIPTION: DC-DC CONVERTER date 08/24/2021 Ϳ page 4 of 7 MECHANICAL DRAWING BOARD MOUNT units: mm[inch] tolerance: ±0.30[±0.012] pin diameter tolerance: ±0.10[±0.004] pin height tolerance: ±0.50[±0.020] PIN CONNECTIONS Function Ctrl 4 Trim 5 0V 6 +Vo 4.10 [0.161] Front View 5 2 6 1 50.80[2.000] 45.72[1.800] 6 1 2 5 3 PCB Layout Top View TI 4 Bottom View SC ON 10.16 [0.400] NU 3 ∅1.00[0.039] 4 3 25.40[1.000] GND 10.16 10.16 [0.400] [0.400] Vin 2 5.08[0.200] 1 2.54 [0.100] PIN Grid Size: 2.54mm x 2.54mm ED 11.80 [0.465] ∅1.50 [0.059] BOARD MOUNT WITH HEATSINK units: mm[inch] tolerance: ±0.30[±0.012] pin diameter tolerance: ±0.10[±0.004] pin height tolerance: ±0.50[±0.020] ∅1.50 [0.059] Grid Size: 2.54mm x 2.54mm PIN CONNECTIONS PIN Function 1 Vin 2 GND 3 Ctrl 4 Trim 0V DI 5 6 +Vo Top View 4 3 5 2 6 1 PCB Layout Top View Front View cui.com Additional Resources: Product Page CUI Inc Ϳ SERIES: PQA30-D Ϳ DESCRIPTION: DC-DC CONVERTER date 08/24/2021 Ϳ page 5 of 7 EMC RECOMMENDED CIRCUIT NU ED DERATING CURVES Table 1 Recommended external circuit components TI Figure 1 Vin (Vdc) 24 FUSE choose according to input current CO N MOV TEST CONFIGURATION S14K35 56µH 56µH TVS SMCJ48A SMCJ90A C0 330µF/50V 330µF/100V C1, C2 4.7µF/50V 2.2µF/100V LCM1 1mH 1mH CY1, CY2 1nF/2kV 1nF/2kV DI S Table 2 External components Lin Nj+ Cin Nj)(65Ÿ at 100 kHz ,QSXWUHÀHFWHGULSSOHFXUUHQWLVPHDVXUHGZLWKDQLQGXFWRU/LQDQG&DSDFLWRU&LQWRVLPXODWHVRXUFHLPSHGDQFH cui.com S14K60 LDM1 Figure 2 1RWH 48 Additional Resources: Product Page CUI Inc Ϳ SERIES: PQA30-D Ϳ DESCRIPTION: DC-DC CONVERTER date 08/24/2021 Ϳ page 6 of 7 APPLICATION NOTES Requirement on output load 7RHQVXUHWKLVPRGXOHFDQRSHUDWHHϒFLHQWO\DQGUHOLDEO\WKHPLQLPXPRXWSXWORDGFDQQRWEHOHVVWKDQRIWKHIXOOORDGGXULQJ operation. If the actual output power is small, please connect a resistor at the output end in parallel to increase the load. 2. Recommended circuit This series has been tested according to the following recommended testing circuit before leaving the factory. This series should be tested under load (see Figure 3). If you want to further decrease the input/output ripple, you can increase capacitance properly or choose capacitors with low ESR (see Table 3). However, the capacitance must not exceed the maximum capacitive load or a start-up problem might arise (see Table 4). Figure 3 UE D 1. Table 3 Cin (µF) Cout (µF) Vout (Vdc) Max. &DSDFLWLYH/RDGNj) 3.3 100 220 3.3 6800 5 100 220 5 6800 IN Vout (Vdc) 9 100 100 9 680 12 100 100 12 680 15 100 100 15 680 24 100 47 24 470 SC ON T 3. Table 4 Output Voltage Trimming Leave open if not used. Figure 4 Formula for Trim Resistor Application Circuit for Trim Pin (part in broken line is the interior of models) up: RT = aR2 -R3 R 2-a a= Vref R1 Vo’-Vref down: R T = aR1 -R3 R 1-a a= Vo’-Vref R2 Vref Note:    DI  Notes:      Value for R1, R2, R3, and Vref (see Table 5) RT: Trim Resistor D8VHUGH¿QHGSDUDPHWHUQRDFWXDOPHDQLQJV Vo': The trim up/down voltage  Table 5 Vout (Vdc) R1 NŸ R2 NŸ R3 NŸ Vref (V) 3.3 4.801 2.863 12 1.24 5 2.883 2.864 10 2.5 9 7.5 2.864 15 2.5 12 10.971 2.864 15 2.5 15 14.497 2.864 15 2.5 24 24.872 2.863 20 2.5 1. Minimum load shouldn't be less than 10%, otherwise ripple may increase dramatically. Operation under minimum load will not damage the converter, however, they may QRWPHHWDOOVSHFL¿FDWLRQVOLVWHG 2. Maximum capacitive load is tested at input voltage range and full load. $OOVSHFL¿FDWLRQVDUHPHDVXUHGDW7D ƒ&KXPLGLW\QRPLQDOLQSXWYROWDJHDQGUDWHGRXWSXWORDGXQOHVVRWKHUZLVHVSHFL¿HG cui.com Additional Resources: Product Page CUI Inc Ϳ SERIES: PQA30-D Ϳ DESCRIPTION: DC-DC CONVERTER date 08/24/2021 Ϳ page 7 of 7 REVISION HISTORY rev. description date initial release 07/08/2014 discontinued heat sink versions 06/21/2019 1.02 safeties updated in features and safety approvals line 01/19/2021 GHUDWLQJFXUYHVDQGFLUFXLW¿JXUHVXSGDWHG 08/24/2021 1.03 ED 1.0 1.01 DI S CO N TI NU The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 Fax 503.612.2383 cui.com techsupport@cui.com &8,RϑHUVDWZR\HDUOLPLWHGZDUUDQW\&RPSOHWHZDUUDQW\LQIRUPDWLRQLVOLVWHGRQRXUZHEVLWH CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a OLIHVXSSRUWGHYLFHRUV\VWHPZKRVHIDLOXUHWRSHUIRUPFDQEHUHDVRQDEO\H[SHFWHGWRFDXVHWKHIDLOXUHRIWKHOLIHVXSSRUWGHYLFHRUV\VWHPRUWRDϑHFWLWVVDIHW\RUHϑHFWLYHQHVV