PQQ6W-Q24-S3-S

Additional Resources: Product Page | 3D Model | PCB Footprint date 02/07/2023 page 1 of 9 SERIES: PQQ6W-S │ DESCRIPTION: DC-DC CONVERTER FEATURES • • • • • • • • • 6W isolated output ultra wide 4:1 input range single and dual regulated outputs high efficiency up to 87% short circuit and over-current protection 1,600 Vdc isolation operating temperature -40°C ~ 105°C control pin designed to meet EN/BS EN 62368 MODEL input voltage output voltage output current output power ripple & noise1 efficiency² typ (Vdc) range (Vdc) (Vdc) min (mA) max (mA) max (W) max (mVp-p) typ (%) PQQ6W-Q24-S3-S 24 9~36 3.3 0 1,350 4 100 78 PQQ6W-Q24-S5-S 24 9~36 5.0 0 1,200 6 100 82 PQQ6W-Q24-S9-S 24 9~36 9.0 0 667 6 100 84 PQQ6W-Q24-S12-S 24 9~36 12.0 0 500 6 100 86 PQQ6W-Q24-S15-S 24 9~36 15.0 0 400 6 100 87 PQQ6W-Q24-S24-S 24 9~36 24.0 0 250 6 100 85 PQQ6W-Q24-D5-S 24 9~36 ±5 0 ±600 6 150 80 PQQ6W-Q24-D9-S 24 9~36 ±9 0 ±333 6 150 83 PQQ6W-Q24-D12-S 24 9~36 ±12 0 ±250 6 150 83 PQQ6W-Q24-D15-S 24 9~36 ±15 0 ±200 6 150 83 PQQ6W-Q24-D24-S 24 9~36 ±24 0 ±125 6 150 82 Notes: 1. Ripple and noise are measured at 20 MHz BW by “parallel cable” method. See Figure 3. 2. At nominal input voltage. 3. Exceeding the maximum input voltage may cause permanent damage. PART NUMBER KEY PQQ6W - QXX - X XX - S Base Number Input Voltage Output S = single D = dual cui.com Output Voltage Packaging style S = SIP Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: PQQ6W-S │ DESCRIPTION: DC-DC CONVERTER date 02/07/2023 │ page 2 of 9 INPUT parameter conditions/description operating input voltage min typ max units 9 24 40 Vdc start-up voltage surge voltage for maximum of 1 second -0.7 current full load / no load 3.3 Vdc output 5 Vdc output 9, 12, 15, 24 Vdc output ±5 Vdc output ±9, ±12, ±15 Vdc output ±24 Vdc output filter capacitance filter CTRL module on: CTRL pin open or pulled high (3.5-12 Vdc) module off: CTRL pin pulled low to GND (0-1.2 Vdc) 283/5 305/5 305/10 313/12 301/12 305/12 9 Vdc 50 Vdc 245/12 313/12 313/16 320/16 309/16 313/16 mA mA mA mA mA mA OUTPUT parameter conditions/description maximum capacitive load4 3.3 Vdc output 5 Vdc output ±5, 9 & 12 Vdc output ±9, 15 Vdc output ±12 Vdc output ±15, 24 Vdc output ±24 Vdc output voltage accuracy 5%~100% load line regulation max units 1,800 1,000 470 220 120 100 68 μF μF μF μF μF μF μF Vout1 Vout2 ±2 ±3 % % at full load, from low to high input voltage Vout1 Vout2 ±1 ±1.5 % % load regulation 5%~100% load Vout1 Vout2 ±1.5 ±2 % % switching frequency PWM mode 500 transient recovery time 25% load step change, nominal input voltage single output models dual output models 300 450 500 500 μS μS transient response deviation 25% load step change, nominal input voltage ±9, ±12, ±15 & ±24 Vdc output all other outputs ±3 ±5 ±5 ±8 % % temperature coefficient at full load ±0.03 %/°C Notes: min 4. The specified maximum capacitive load for positive and negative output is identical. cui.com typ kHz Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: PQQ6W-S │ DESCRIPTION: DC-DC CONVERTER date 02/07/2023 │ page 3 of 9 PROTECTIONS parameter conditions/description min over current protection short circuit protection typ 110 max units 230 % max units continuous, auto recovery SAFETY AND COMPLIANCE parameter conditions/description isolation voltage input to output, for 1 minute with 1 mA max single output models dual output models min typ 1,600 1,500 isolation resistance input to output at 500 Vdc 1,000 isolation capacitance input to output, 100 kHz / 0.1 V safety approvals designed to meet 62368-1: EN/BS EN EMI/EMC CISPR32/EN 55032 Class B (see recommended circuit) ESD IEC/EN 61000-4-2 Contact ±4kV, perf. Criteria B radiated immunity IEC/EN61000-4-3 10V/m, perf. Criteria A EFT/burst IEC/EN61000-4-4 ±2KV (see recommended circuit), perf. Criteria B surge IEC/EN61000-4-5 line to line ±2KV (see recommended circuit), perf. Criteria B conducted immunity IEC/EN61000-4-6 3 Vr.m.s, perf. Criteria A MTBF as per MIL-HDBK-217F, 25°C RoHS yes Vdc Vdc MΩ 1,000 pF 1,000 K hours ENVIRONMENTAL parameter conditions/description min operating temperature see derating curve single output models dual output models storage temperature storage humidity non-condensing vibration 10-150Hz, 5G, 0.75mm. along X, Y and Z cui.com typ max units -40 -40 105 85 °C °C -55 125 °C 5 95 % Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: PQQ6W-S │ DESCRIPTION: DC-DC CONVERTER date 02/07/2023 │ page 4 of 9 MECHANICAL parameter conditions/description dimensions 22.00 × 9.50 × 12.00 [0.866 x 0.374 x 0.472 inch] min case material black plastic weight typ units: mm [inch] pin section tolerance: ±0.10[±0.004] general tolerance: ±0.50[±0.020] PIN Out PIN Function Single output Function Dual output 1 GND GND 2 Vin Vin 3 Ctrl Ctrl 5 NC NC 6 +Vout +Vout 7 0V 0V 8 NC -Vout NC: Pin to be isolated from circuitry. cui.com units mm 4.9 MECHANICAL DRAWING max g Additional Resources: Product Page | CUI Inc │ SERIES: PQQ6W-S │ DESCRIPTION: DC-DC CONVERTER 3D Model | PCB Footprint date 02/07/2023 │ page 5 of 9 DERATING CURVE cui.com Additional Resources: Product Page | CUI Inc │ SERIES: PQQ6W-S │ DESCRIPTION: DC-DC CONVERTER 3D Model | PCB Footprint date 02/07/2023 │ page 6 of 9 EFFICIENCY CURVES cui.com Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: PQQ6W-S │ DESCRIPTION: DC-DC CONVERTER date 02/07/2023 │ page 7 of 9 APPLICATION CIRCUIT All the DC-DC converters of this series are tested before delivery using the recommended circuit shown in Fig. 1. Input and/or output ripple can be further reduced by appropriately increasing the input & output capacitor values Cin and Cout and/or by selecting capacitors with a low ESR (equivalent series resistance). Also make sure that the capacitance is not exceeding the max. capacitive load value of the product. Figure 1 Single output Table 1 Dual output Cin (μF/V) Cout (μF/V) 100μF / 50V 22μF / 50V EMC RECOMMENDED CIRCUIT Figure 2 Single output Table 2 Model FUSE Dual output Dual output Choose according to actual input current C0, C4 330μF/50V 330μF/100V C1, C2 10μF/50V 10μF/50V C3 22μF/50V 10μF/50V LCM1 cui.com Single output 1.4-1.7mH (TN150-RH12.7*12.7*7.9) LDM1 --- 10μH CY1, CY2 1nF/400V 1nF/2kV Additional Resources: Product Page | CUI Inc │ SERIES: PQQ6W-S │ DESCRIPTION: DC-DC CONVERTER 3D Model | PCB Footprint date 02/07/2023 │ page 8 of 9 RIPPLE AND NOISE Figure 3 cui.com Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: PQQ6W-S │ DESCRIPTION: DC-DC CONVERTER date 02/07/2023 │ page 9 of 9 REVISION HISTORY rev. description date 1.0 initial release 09/22/2020 1.01 datasheet update 01/21/2021 1.02 product image updated, dual output models added 11/07/2022 1.03 CE safety mark removed 11/22/2022 1.04 efficiency curves updated 12/13/2022 1.05 features updated 02/07/2023 The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 Fax 503.612.2383 cui.com techsupport@cui.com CUI offers a two (2) year limited warranty. Complete warranty information is listed on our website. CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.