PXO7806-500-M-TR

Additional Resources: Product Page | 3D Model | PCB Footprint date 09/12/2023 page 1 of 6 SERIES: PXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR FEATURES • • • • • • • ultra-thin SMD package open frame efficiency up to 95% no-load input current as low as 0.2 mA -40°C ~ 85°C temperature range designed to meet EN/UKCA 62368 output short circuit protection MODEL input voltage1 output voltage output current output power ripple & noise2 efficiency3 typ (Vdc) range (Vdc) (Vdc) max (mA) max (W) max (mVp-p) typ (%) PXO7803-500-M-TR 24 4.75~36 3.3 500 1.65 100 85 PXO7805-500-M-TR 24 6.5~36 5 500 2.5 100 90 PXO7806-500-M-TR 24 8~36 6.5 500 3.25 100 91 PXO7809-500-M-TR 24 12~36 9 500 4.5 100 93 PXO7812-500-M-TR 24 15~36 12 500 6.0 100 94 PXO7815-500-M-TR 24 19~36 15 500 7.5 100 95 Notes: 1. For input voltages higher than 30 Vdc, a 22 µF / 50 V input capacitor is required. 2. Tested at nominal input, 30~100% load for 3.3 Vdc model, 20 MHz bandwidth. At loads below 30%, the max ripple and noise of the 3.3 Vdc output will be 200 mVp-p, and a load below 20% for the other outputs the levels increase to 250 mVp-p.. 3. Measured at min Vin, full load. 4. All specifications are measured at Ta=25°C, humidity < 75%, nominal input voltage, and rated output load unless otherwise specified. PART NUMBER KEY PXO78 XX - 500 - M - TR Base Number Output Voltage cui.com Output Current Packaging: TR = Tape and Reel Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: PXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR date 09/12/2023 │ page 2 of 6 INPUT parameter conditions/description min operating input voltage typ max units 24 36 Vdc 5.0 0.2 8.0 1.5 mA mA typ max units 680 μF input reverse polarity protection no no-load input current 3.3 Vdc output model all other output models filter capacitor filter OUTPUT parameter conditions/description min maximum capacitive load voltage accuracy at full load, input voltage range 3.3 Vdc output model all other models ±2 ±2 ±4 ±3 % % line regulation at full load, input voltage range ±0.3 ±0.5 % load regulation at nominal input, 10~100% load ±0.6 ±1 % switching frequency at nominal input voltage, full load 3.3 Vdc output model all other output models 750 700 1,250 kHz kHz transient recovery time at nominal input voltage, 25% load step change 0.2 1 ms transient response deviation at nominal input voltage, 25% load step change ±50 ±250 temperature coefficient at full load ±0.02 mV %/°C PROTECTIONS parameter conditions/description short circuit protection continuous, auto recovery min typ max units min typ max units SAFETY AND COMPLIANCE parameter conditions/description safety approvals designed to meet 62368: EN/IEC/UKCA conducted emissions5 CISPR32/EN55032 CLASS B (see Fig. 4-2 for recommended circuit) radiated emissions CISPR32/EN55032 CLASS B (see Fig. 4-2 for recommended circuit) ESD IEC/EN 61000-4-2 Contact ±4kV, perf. Criteria B radiated immunity IEC/EN 61000-4-3 10V/m, perf. Criteria B EFT/burst IEC/EN 61000-4-4 100kHz±1kV (see Fig. 4-1 for recommended circuit), perf. Criteria B surge IEC/EN 61000-4-5 ±1kV (see Fig. 4-1 for recommended circuit), perf. Criteria B conducted immunity IEC/EN 61000-4-6 3Vr.m.s, perf. Criteria B MTBF as per MIL-HDBK-217F, 25°C RoHS yes 5 Note: 2,000 000 3. CISPR22/EN55022, class A for the 3.3 Vdc output model. cui.com hours Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: PXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR date 09/12/2023 │ page 3 of 6 ENVIRONMENTAL parameter conditions/description min max units operating temperature see derating curve -40 85 °C -55 125 °C 5 95 % max units 260 °C max units storage temperature storage humidity non-condensing typ SOLDERABILITY parameter conditions/description min reflow soldering Peak temp. ≤245°C, maximum duration time ≤60s over 217°C. Please refer to IPC/JEDEC J-STD-020D.1 typ MECHANICAL parameter conditions/description dimensions 12 x 12 x 4.5 [0.472 x 0.472 x 0.177 inch] min weight cooling method typ mm 0.75 g natural convection MECHANICAL DRAWING units: mm [inch] tolerance: ±0.25[±0.010] PIN-OUT cui.com PIN FUNCTION 1 +Vin 2 NC 3 +Vo 4 GND Additional Resources: Product Page | 3D Model CUI Inc │ SERIES: PXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR DERATING CURVE Figure 1 EFFICIENCY CURVES cui.com | PCB Footprint date 09/12/2023 │ page 4 of 6 Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: PXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR date 09/12/2023 │ page 5 of 6 TYPICAL APPLICATION CIRCUIT Figure 2 Table 1 External Capacitor Table Model Number Note: 1. 2. 3. 4. C1 C2 (ceramic capacitor) (ceramic capacitor) PXO7803-500-M-TR 10 μF/50 V 22 μF/10 V PXO7805-500-M-TR 10 μF/50 V 22 μF/10 V PXO7806-500-M-TR 10 μF/50 V 22 μF/16 V PXO7809-500-M-TR 10 μF/50 V 22 μF/16 V PXO7812-500-M-TR 10 μF/50 V 22 μF/25 V PXO7815-500-M-TR 10 μF/50 V 22 μF/25 V The required C1 and C2 capacitors must be connected as close as possible to the terminals of the module. Refer to Table 1 for C1 and C2 capacitor values. For certain applications, increased values and/or tantalum or low ESR electrolytic capacitors may also be used instead. Converter cannot be used for hot swap or with output in parallel. To further reduce the output ripple and noise, we suggested the use of a “LC” filter at the output terminals, with an inductor value (L) of 10µH-47µH. Figure 3 External “LC” output filter circuit diagram EMC RECOMMENDED CIRCUIT Figure 4 Table 2 Recommended external circuit components Note: FUSE choose according to actual input current MOV S20K30 LDM1 82 µH C0 680 µF/50 V C1 / C2 see Table 1 C5 4.7 µF/50 V LDM2 22 µH For EMC tests we use Part ① in Fig. 4 for immunity and part ➁ for emissions test. Selecting based on needs. cui.com Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: PXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR date 09/12/2023 │ page 6 of 6 REVISION HISTORY rev. description date 1.0 initial release 08/30/2022 1.01 switching frequency, no load input current, ripple & noise, and emissions updated for 3.3 Vdc output model 05/23/2023 efficiency curves updated 09/12/2023 1.02 The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 Fax 503.612.2383 cui.com techsupport@cui.com CUI offers a two (2) year limited warranty. Complete warranty information is listed on our website. CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.