VXO7803-500-M-TR

Additional Resources: Product Page | 3D Model | PCB Footprint date 04/06/2023 page 1 of 6 SERIES: VXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR FEATURES • • • • • • ultra-thin SMD Package, thickness ≤3.5 mm open frame high efficiency up to 95% no-load input current as low as 0.2 mA wide temperature range: -40°C ~ +85°C output short-circuit protection MODEL input voltage1 output voltage output current output power ripple & noise2 efficiency3 typ (Vdc) range (Vdc) (Vdc) max (mA) max (W) max (mVp-p) typ (%) VXO7803-500-M 24 4.75~36 3.3 500 1.65 50 86 VXO7805-500-M 24 6.5~36 5 500 2.5 50 90 VXO7809-500-M 24 12~36 9 500 4.5 50 93 VXO78012-500-M 24 15~36 12 500 6 50 94 VXO78015-500-M 24 19~36 15 500 7.5 50 95 Notes: 1. For input voltages higher than 30 Vdc, a 22 µF / 50 V input capacitor is required. 2. Tested at nominal input, 20~100% load for 3.3 Vdc model, 20 MHz bandwidth, with 10 µF electrolytic and 1 µF ceramic capacitor on the output. At loads below 10%, the max ripple and noise of the 3.3 & 5 Vdc outputs will be 150 mVp-p, and the other outputs will be 2% Vo. 3. Measured at min Vin, full load. 4. All specifications are measured at Ta=25°C, humidity < 75%, nominal input voltage, and rated output load unless otherwise specified. PART NUMBER KEY VXO78 XXX - 500 - M - TR Base Number Output Voltage Output Current cui.com Packaging: TR = Tape and reel Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: VXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR date 04/06/2023 │ page 2 of 6 INPUT parameter conditions/description operating input voltage1 for positive output applications filter capacitor filter min typ max units 24 36 Vdc 0.2 1.5 mA input reverse polarity protection no no-load input current positive outputs Ctrl*2 module on Ctrl pin open or pulled high (TTL 3.2-8VDC) module off Ctrl pin pulled low to GND (0-0.8VDC) input current when off Note: 30 100 µA typ max units 680 μF 1. See Model section on page 1 for specific input voltage ranges. 2. The Ctrl pin voltage is referenced to input GND. OUTPUT parameter conditions/description min maximum capacitive load for positive output applications voltage accuracy at full load, input voltage range 3.3 Vdc output model all other models ±2 ±2 ±4 ±3 % % line regulation at full load, input voltage range ±0.2 ±0.4 % load regulation at nominal input, 10~100% load 3.3 Vdc output model all other models ±0.6 ±0.3 switching frequency at nominal input voltage, full load 700 transient recovery time at nominal input voltage, 25% load step change 0.2 transient response deviation at nominal input voltage, 25% load step change 50 temperature coefficient at full load 3 Note: % % kHz 1 ms 200 mV ±0.03 %/°C 3. The maximum capacitive load was tested at nominal input voltage, full load. PROTECTIONS parameter conditions/description short circuit protection continuous, auto recovery min typ max units min typ max units SAFETY AND COMPLIANCE parameter conditions/description safety approvals designed to meet 62368-1: EN, BS EN conducted emissions CISPR32/EN55032 Class B (see Fig. 4-2 for recommended circuit) radiated emissions CISPR32/EN55032 Class B (see Fig. 4-2 for recommended circuit) ESD IEC/EN61000-4-2, contact ± 4kV, perf. Criteria B radiated immunity IEC/EN61000-4-3, 10V/m, perf. Criteria A EFT/burst IEC/EN61000-4-4, ± 1kV (see Fig. 4-1 for recommended circuit), perf. Criteria B surge IEC/EN61000-4-5, line-line ± 1kV (see Fig. 4-1 for recommended circuit), perf. Criteria B conducted immunity IEC/EN61000-4-6, 3 Vr.m.s, perf. Criteria A MTBF as per MIL-HDBK-217F, 25°C RoHS 2011/65/EU 2,000 cui.com K hours Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: VXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR date 04/06/2023 │ page 3 of 6 ENVIRONMENTAL parameter conditions/description min max units operating temperature see derating curve -40 85 °C -55 125 °C 5 95 % max units 260 °C max units storage temperature storage humidity non-condensing typ SOLDERABILITY parameter conditions/description min reflow soldering Peak temp. ≤245°C, maximum duration time ≤60s over 217°C. Please refer to IPC/JEDEC J-STD-020D.1 typ MECHANICAL parameter conditions/description dimensions 12.50 x 13.50 x 3.50 [0.492 x 0.531 x 0.138 inch] min weight typ mm 0.9 MECHANICAL DRAWING units: mm [inch] tolerance: ±0.25[±0.010] pin diameter tolerance: ±0.10[±0.004] PIN-OUT PIN FUNCTION 1 +Vin 2 GND 3 +Vo 4 Remote on/off cui.com g Additional Resources: Product Page | 3D Model CUI Inc │ SERIES: VXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR DERATING CURVE Figure 1 EFFICIENCY CURVES cui.com | PCB Footprint date 04/06/2023 │ page 4 of 6 Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: VXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR date 04/06/2023 │ page 5 of 6 TYPICAL APPLICATION CIRCUIT Figure 2 Table 1 External Capacitor Table Model Number C1, C3 C2, C4 (ceramic capacitor) (ceramic capacitor) VXO7803-500-M 10 μF/50 V 22 μF/10 V VXO7805-500-M 10 μF/50 V 22 μF/16 V VXO7809-500-M 10 μF/50 V 22 μF/25 V VXO78012-500-M 10 μF/50 V 22 μF/25 V VXO78015-500-M 10 μF/50 V 22 μF/25 V Note: 1.C1 and C2 (C3 and C4) are required and should be connected close to the pin terminal of the module. 2.The capacitance of C1 and C2 (C3 and C4) refer to Sheet 1, it can be increased properly if required, and tantalum or low ESR electrolytic capacitors may also suffice. 3.When the products used as the circuit like figure 3, an inductor named as LDM up to 10μH is recommended in the circuit to reduce the mutual interference. 4.Cannot be used in parallel for output and hot swap. To reduce the output ripple furtherly, it is suggested to connect a “LC” filter at the output terminal, and recommended value of L is 10µH-47µH. Figure 3 External “LC” output filter circuit diagram EMC RECOMMENDED CIRCUIT Figure 4 Table 2 Recommended external circuit components Note: FUSE choose according to actual input current LDM1 82 µH C0, C3 330 µF/50 V C4 see Table 1 C1, C2 10 µF/50 V LDM2 22 µH For EMC tests we use Part ① in Fig. 4 for immunity and part ➁ for emissions test. Selecting based on needs. cui.com Additional Resources: Product Page | 3D Model | PCB Footprint CUI Inc │ SERIES: VXO78-500-M │ DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR date 04/06/2023 │ page 6 of 6 REVISION HISTORY rev. description date 1.0 initial release 01/22/2020 1.01 Ctrl added 04/13/2020 1.02 derating curve, efficiency curves and circuit figures updated 09/17/2021 1.03 PN for 12V & 15V model updated 09/04/2022 1.04 PN key updated 01/26/2023 1.05 safeties updated 04/06/2023 The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 Fax 503.612.2383 cui.com techsupport@cui.com CUI offers a two (2) year limited warranty. Complete warranty information is listed on our website. CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.