Swidget® and Sydewynder®
Miniature
Switches
INDUSTRIES
Side Actuated
Features:
Top Actuated
I 1"
End Actuated
One through four poles
Two through five positions
For switching up to 8.5 amps at
125 volts ac
Detent or spring return
Panel or PC board mount
Top, side, or end actuation
Solder, solderless, or wire wrap
termination
U.L. recognized, C.S.A. listed
4 pt. PC Board Mount
ISO 9001 REGISTERED
Catalog S2120-III/03
INDUSTRIES 130 James Way, Southampton, PA 18966-3838-Tel. 215-355-7080 • Fax 215-355-1088 • www.cwind.com
Slide switches became popular in America with industrial expansion after World War I. The "standard" two
position switch was designed for chassis mount on two
1.125-inch centered mounting holes. Terminals were
designed for convenience in hand soldering. Actuation
was with a trigger extending out the switch top, and
generally switches were constructed for switching up
to 3.0 amps at 125 volts ac. With the development of
densely packed printed circuit boards, new materials,
and new innovative requirements, design engineers
found needs for switching higher and lower currents
and voltages in smaller switch packages having a wide
variety of terminations as well as actuation from switch
sides, ends, and tops.
In response to industry's need for miniaturization,
CW first developed its miniature "Swidget"® line of
slide switches; and for printed circuit board applications, its "Sydwynders"®. CW's line of miniature
Swidgets® now has capability of switching currents up
to 8.5 amps, four poles concurrently and five posi-
tions consecutively. Switching can be by toggle, front,
side, and top actuating knobs. Terminals for solder,
printed circuit board, wire wrap, and solderless termination are also available.
This vast variety of switch types and options has
increased and multiplied the types of equipment into
which CW switches have been designed and are
used...with time-proven reliability at moderate prices.
From early applications in toys, kits, and games, our
switches are now used everywhere.. .from low voltage, low current to heavy duty switching.. .from calculators, computers, and sensitive instruments to hair
blowers, automobiles, and refrigerators...and TV,
home appliances, and aerospace devices, too.
CW's switch parts and assemblies are manufactured in CW's fully integrated manufacturing facilities.
All processes are performed and controlled by CW's
highly trained and technically competent personnel.
Housing
Solid, one-piece actuating button and contact
seat
Spring assures positive
electrical contact
Long travel of moving
contact over stationary
contact assures contact
cleanliness and results in
low contact resistance
V
2
Terminal
Terminal board
MINIATURE SLIDE SHIFT SELECTION GUIDE
Top-Actuated Panel Mount
Model
Circuit
GF-123
spst detent
5
GF-124
spdt detent
5
G-134
spst spring return
5
G-133
spdt spring return
5
G-223
spst spring return (push)
6
GF-125
dpst detent
6
GF-126
dpdt detent
6
GF-161
Spdt detent
7
Model
Circuit
G-127
spSpos detent
7
GPF-124
spdt detent
13
G-173
spSpos spring return
8
GP-132
spdt spring return
13
G-128
dpSpos detent
7
GPF-126
dpdt detent
13
G-175
dpSpos spring return
8
G-168
SpSpos detent
9
G-169
4p3pos detent
9
G-140
sp4pos detent
10
G-141
dp4pos detent
10
Page No.
Side-Actuated Panel Mount
Top-Actuated
4-Point PC Board Mount
Page No.
Side-Actuated
4-Point PC Board Mount
Page No.
Model
Circuit
GPI-151
spdt detent
14
GPI-152
dpdt detent
14
GPI-153
spSpos detent
14
GPI-154
dpSpos detent
14
Model
Circuit
GI-151
spdt detent
11
GI-152
dpdt detent
11
GF-165
Spdt detent
12
GI-153
spSpos detent
11
GI-154
dpSpos detent
11
GI-158
sp4pos detent
12
Model
Circuit
GI-159
dp4pos detent
12
G-133 PCE
spdt spring return
GI-163
dpSpos detent
13
Page No.
End-Actuated
PC Board Mount
Page No.
14
INDUSTRIES 130 James Way, Southampton, PA 18966-3838 -Tel. 215-355-7080 • Fax 215-355-1088 • www.cwind.com
PERFORMANCE STANDARDS
MATERIALS OF CONSTRUCTION
CW switches are designed to perform to the standards listed
when operated within ambient conditions detailed below:
Operating temperature—104°C maximum, -10°C
minimum.
Relative humidity—Switches will be operable and insulation resistance shall be greater than 100 megohms if allowed
to dry for 100 hours at room temperature of 25°C and after
exposure for one hour in an atmosphere having 95% relative
humidity and a temperature of 50°C.
High voltage breakdown—Minimum of 1000 volts rms 60 Hz
for one minute between parts of opposite polarity.
Contact resistance—Less than 0.01 ohm at 20
milliamperes dc.
Life cycling (no load)—Switches will be operative after
10,000 (minimum) cycles at the rate of 10 cycles per minute.
Life cycling (load)—Switches will be operative after 6000
(minimum) cycles at the rate of 10 cycles per minute at
rated load.
Buttons—Black type 6/6 nylon.
Housings—Cold-rolled steel.
Housing plating—4-point PC board mount switches-electro-tin; others-zinc followed by clear chromate.
Moving contact—Copper or copper alloy.
Moving contact plating—Silver is standard. Gold (30
microinches of gold over 50 microinches of nickel) is available.
Other gold thicknesses are available if your quantities are
sufficient.
Moving contact spring—Phosphor bronze or beryllium
copper.
Terminals—Copper.
Terminal plating—Silver is standard. Gold (30 microinches
over 50 microinches of nickel) on many popular types is
available.
Terminal board—NEMA Grade XP phenolic laminate.
CARE IN SWITCH INSTALLATION
CW switches will perform properly if they are installed and
used properly. Causes for failure often encountered in the
field that are the responsibility of the user are:
1. Removal of factory applied lubricants from switch contacts and moving parts.
2. Introduction of foreign material into switching mecha-
J
(Other materials to suit your application are available if volume is sufficient. Consult factory.)
nism...flux, solder, cleaning materials, potting
compounds.
3. Restriction of movement of switch button.
4. Excessive heat often introduced while soldering.
5. Switching loads in excess of rating.
Manufacturing Engineers are cautioned to avoid misusing
switches and resultant switch failures.
J
U.L.ANDC.S.A.
CW test laboratories are fully equipped to monitor and test
CW switches to U.L. and C.S.A. published standards. Most
CW switches are listed by these agencies as having conformed to those standards in tests applied on a continuing
basis. A record of types of CW switches listed is retained in
U.L. File Number E-9556 and in C.S.A. File Number
LR20985.
AVAILABLE OPTIONS
G-02-56
CW PATENTS
CW Engineers are constantly trying to upgrade the quality
and cost effectiveness of our switches. Often this results in
new inventions. Switch products shown in this catalog may
be covered by one or more of the following U.S. patents:
3,270,149
3,993,881
3,271,535
4,404,437
3,311,719
4,128,745
3,461,252
4,410,232
Other patent applications are pending.
HOW TO ORDER
Specify CW part number by referencing drawing that shows
switch of your choice. If switch you require differs from drawing, specify differences from options available.
"Toppers"—Shown are toppers that can change your panel
appearance and product styling.
Terminals—CW switches can be terminated by hand solder, PC board, wire-wrap, or receptacle. See page 15 for terminal options.
Solder Shields—For hand-soldered terminations or for added
protection against flux, solder and foreign materials, request
.002" thick vulcanized fiber shield shipped separately or assembled to switch terminals. On single pole switches, solder
shields are available for switches having "IN LINE" terminals
only.
Hot Stamping—Functional or decorative marking of your
choice can be imprinted on the "Topper" with CW's "inhouse" facilities.
Colors—CW stores molding powders in many colors. "Toppers" and buttons are available in a variety of colors if your
quantity is sufficient.
INDUSTRIES 130 James Way, Southampton, PA 18966-3838 -Tel. 215-355-7080 • Fax 215-355-1088 • www.cwind.com
TOP-ACTUATED PANEL MOUNT MINIATURE SWIDGETS
GF-123 Single Pole/Single Throw (with detent)
GF-124 Single Pole/Double Throw (with detent)
P.C. LAYOUT
INLINE
ACTUATOR KNOB
Decorative aluminum sleeved actuating knob is available.
Specify GB-123 or GB-124 with appropriate suffix indicating
your current requirements. .453" knob height shown is
standard. Also available in heights of .162" (4.11 mm), .200"
(5.08 mm), .473" (12.01 mm), .569" (14.27 mm), and .709"
(18.01 mm).
":>-]
\_.IOO m. ?HO| p_ . ; n | .
(2 _ 54) DIA.2 HOLES
(|
+.,o jDIA.6HOLES
(5.O8±.'»)
(.41)
1
-735
REF
?
__
P
t
.250*.°'°
[6.35±.»J
.f8l±.o'° T Y P
(4.60±-")IY*
.078 TVD
.020 TYp _. i_
(.5I) TYR
.292±-°*°
.
DPST versions have two end terminals (shown in
blue) removed.
LOGIC SWITCH GF-126-500
Same as GF-126, except the button of this switch is sliced in
half so that each pole can be actuated independently or simultaneously with the other pole, as desired. Four different
conditions of a circuit can be attained. Included is one black
button half and one white
button half.
•«»-:..._
LISTING*
ELECTRICAL RATING
TYPE
U.L&C.S.A.
0.5Aat125Vac/Vdc
GF-125
U.L&C.S.A.
3.0Aac,0.5Aat125Vdc
GF-125-3
U.L&C.S.A.
8.5Aac,0.5Aat125Vdc
GF-125-8.5
U.L&C.S.A.
0.5Aat125Vac/Vdc
GF-126
U.L&C.S.A.
3.0Aac,0.5Aat125Vdc
GF-126-3
U.L&C.S.A.
8.5Aac,0.5Aat125Vdc
GF-126-8.5
U.L&C.S.A.
0.5Aat125Vac/Vdc
GF-126-500
'Specify C.S.A. listing, if required
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper". See page 4.
BUTTONS
.200" (5.08 mm) button height shown is standard.
Other heights available are .125" (3.18 mm), .328" (8.3 mm),
and .453" (11.51 mm).
MOUNTING
PANEL—Two .100" diameter holes on .812" centers. 4-40
extruded and tapped mounting holes are also available.
PRINTED CIRCUIT BOARD—Plug directly into board having hole pattern suggested in drawing.
TERMINALS
Standard is solder terminal G-20-28 as shown. For PC applications, we suggest G-20-18, but you may specify the terminal of your choice from those shown on page 15.
SOLDER SHIELD
Vulcanized fiber shield .020" thick may be shipped assembled or separate as requested.
ACTUATOR KNOB
Decorative aluminum sleeved actuating knob is available.
Same as shown on pg. 5. Specify GB-125 or GB-126 with
appropriate suffix indicating your current requirement. .453"
knob height shown is standard. Also available in heights of
.162" (4.11 mm), .200" (5.08 mm), .562 (14.27 mm), and
.709" (18.01 mm).
INDUSTRIES 130 James Way, Southampton, PA 18966-3838 »Tel. 215-355-7080 • Fax 215-355-1088 • www.cwind.com
TOP-ACTUATED PANEL MOUNT MINIATURE SWIDGETS
GF-161 Three Pole/Double Throw (with detent)
TYPE
GF-161
GF-161-3
GF-161-8.5
ELECTRICAL RATING
0.5Aat125Vac/Vdc
3.0Aac,0.5Aat125Vdc
8.5Aac,0.5Aat125Vdc
LISTING*
U.L&C.S.A.
U.L&C.S.A.
U.L&C.S.A.
'Specify C.S.A. listing, if required.
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper". See page 4.
BUTTONS
.200" (5.08 mm) button height shown is standard.
Other heights available are .100" (2.54 mm), .328"
(8.33 mm) and .453" (11.51 mm).
MOUNTING
PANEL—Two .100" diameter holes on .812" centers. 4-40
extruded and tapped holes are available or plug directly into
board having hole pattern shown.
TERMINALS
Standard is solder terminal G-20-28 as shown. For PC applications, we suggest G-20-18, but you may specify the terminal of your choice from those shown on page 15.
SOLDER SHIELD
Vulcanized fiber shield .020" thick may be shipped assembled or separate as requested.
G-127L Single Pole/Three Position (with detent)
G-128LTwo Pole/Three Position (with detent)
Drawing shows button in extreme right position
where LONG detent plate covers topside opening to
the left of the button and extends beyond (in blue)
housing on right. Specify G-127L or G-128L with suffix
indicating current requirement. If topside opening need
not be covered, specify G-127S or G-128S with appropriate suffix.
TYPE
ELECTRICAL RATING
LISTING*
*G-127L/S
.05Aat125Vac/Vdc
U.L&C.S.A.
*G-128L/S
.05Aat125Vac/Vdc
U.L&C.S.A.
*G-127L/S-3
3.0Aac,0.5Aat125Vdc U.L&C.S.A.
*G-128L/S-3
3.0Aac,0.5Aat125Vdc U.L&C.S.A.
*G-127L/S-6
6.0Aac,0.5Aat125Vdc U.L&C.S.A.
*G-128L/S-6
6.0Aac,0.5Aat125Vdc U.L&C.S.A.
'G-127L/S-8.5 8.5Aac,0.5Aat125Vdc
U.L&C.S.A.
'G-128L/S-8.5 8.5Aac,0.5Aat125Vdc U.L&C.S.A.
*Order either G-127L or G-127S or either G-128L or G-128S
depending on your need for long or short detent plate as
described.
'Specify C.S.A. listing, if required.
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper." See page 4.
BUTTONS
.200" (5.08 mm) button height shown is standard.
Other heights available are .125" (3.18 mm), .328"
(8.33 mm), and .453" (11.51 mm).
MOUNTING
PANEL—Two .100" diameter holes on 1.000" centers. 4-40
extruded and tapped holes are available.
PRINTED CIRCUIT BOARD—Plug directly into printed circuit board having hole pattern mating with your switch terminals. Standard G-127L/S single pole terminal orientation is
INLINE. For greater switch stability on your PC board before
soldering, specify STAGGERED terminals.
TERMINALS
Standard is solder terminal G-20-28 as shown. For PC applications, we suggest G-20-18, but you may specify the terminal of your choice from those shown on page 15.
SOLDER SHIELD
Vulcanized fiber shield .020" thick may be shipped assembled or separate as requested.
INDUSTRIES 130 James Way, Southampton, PA 18966-3838 -Tel. 215-355-7080 • Fax 215-355-1088 ••www.cwind.com
TOP-ACTUATED PANEL MOUNT MINIATURE SWIDGETS
G-173 Single Pole/Three Position (spring return, both
ends to center)
ELECTRICAL RATING
0.5Aat125Vac/Vdc
LISTING*
U.L&C.S.A.
*SpecifyC.S.A. listing, if required
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper". See page 4.
BUTTONS
.200" (5.08 mm) button height shown is standard.
Other heights available are .328" (8.33 mm) and
.438" (11.13 mm).
MOUNTING
PANEL—Two. 100" diameter holes on 1.000" centers.
PRINTED CIRCUIT BOARD—Plug directly into a printed
circuit board having the suggested hole pattern shown.
TERMINALS
Standard is solder terminal G-20-28 as shown. For PC applications, we suggest G-20-18, but you may specify the terminal of your choice from those shown on page 15.
SOLDER SHIELD
Vulcanized fiber shield .020" thick may be shipped assembled or separate as requested.
J
G-175 Double Pole/Three Position (spring return, both
ends, to center)
8
ELECTRICAL RATING
LISTING
0.5Aat125Vac/Vdc
U.L
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper". See page 4.
BUTTONS
.200" (5.08 mm) button height shown is standard.
Also available is .328" (8.33 mm).
MOUNTING
PANEL—Two .100" diameter holes on 1.000" centers. Also
available are 4-40 extruded and tapped holes.
PRINTED CIRCUIT BOARD—Plug directly into board having hole pattern shown.
TERMINALS
Standard is solder terminal G-20-28 as shown. For PC applications, we suggest G-20-18, but you may specify the terminal of your choice from those shown on page 15.
VUP INDUSTRIES 130 James Way, Southampton, PA 18966-3838-Tel. 215-355-7080 • Fax 215-355-1088 • www.cwind.com
TOP-ACTUATED PANEL MOUNT MINIATURE SWIDGETS
G-168 Three Pole/Three Position (with detent)
P.C. LAYOUT
.046
(1.17} DIA. TYP
TYPE
ELECTRICAL RATING
LISTING
G-168-L
0.5Aat125Vac/Vdc
U.L
G-168-S
0.5Aat125Vac/Vdc
U.L
G-168-L-3
3.0Aac,0.5Aat125Vdc
U.L.
G-168-S-3
3.0Aac,0.5Aat125Vdc
U.L.
G-168-L-8.5
8.5Aac,0.5Aat125Vdc
U.L
G-168-S-8.5
8.5Aac,0.5Aat125Vdc
U.L
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper". See page 4.
BUTTONS
.200" (5.08 mm) button height shown is standard.
Other heights available are .328" (8.33 mm) and .453"
(11.51 mm).
MOUNTING
PANEL—Two .100" diameter holes on 1.000" centers. Also
available are 4-40 extruded and tapped holes.
PRINTED CIRCUIT BOARD—Plug directly into printed circuit board having hole pattern shown.
TERMINALS
Standard is solder terminal G-20-28 as shown. For PC applications, we suggest G-20-18, but you may specify the terminal of your choice from those shown on page 15.
Drawing shows button in extreme right position where LONG
detent plate covers topside opening to the left of the button
and extends beyond (in blue) housing on right. Specify
G-168L with suffix indicating current requirement. If topside
opening need not be covered, specify G-168S with appropriate suffix.
G-169 Four Pole/Three Position (with detent)
P C.LAYOUT
'r~^
I
w
.060-:8lT/f
T~
i '.--iii5oVEF-
rf
M
Drawing shows button in extreme right position where LONG
detent plate covers topside opening to the left of the button
and extends beyond (in blue) housing on right. Specify
G-169L with suffix indicating current requirement. If topside
opening need not be covered, specify G-169S with appropriate suffix.
TYPE
ELECTRICAL RATING
LISTING*
G-169-L
0.5Aat125Vac/Vdc
U.L&C.S.A.
G-169-S
0.5Aat125Vac/Vdc
U.L&C.S.A.
G-169-L-3
3.0Aac,0.5Aat125Vdc
U.L&C.S.A.
G-169-S-3
3.0Aac,0.5Aat125Vdc
U.L&C.S.A.
'Specify C.S.A. listing, if required.
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper". See page 4.
BUTTONS
.200" (5.08 mm) button height shown is standard.
Other heights available are .125" (3.18mm), .328"
(8.33 mm), and .453" (11.51 mm).
MOUNTING
PANEL—Two. 100" diameter holes on 1.000" centers. 4-40
extruded and tapped holes are available.
PRINTED CIRCUIT BOARD—Plug directly into printed circuit board having hole pattern shown.
TERMINALS
Standard is solder terminal G-20-28 as shown. For PC applications, we suggest G-20-18, but you may specify the terminal of your choice from those shown on page 15.
SOLDER SHIELD
Vulcanized fiber shield .020" thick may be shipped assembled or separate as requested.
INDUSTRIES 130 James Way, Southampton, PA 18966-3838 • Tel. 215-355-7080 • Fax 215-355-1088 • www.cwind.com
9
TOP-ACTUATED PANEL MOUNT MINIATURE SWIDGETS
G-140 Single Pole/Four Position (with detent)
{4.521-os)
.I78+-002
(4.52±.os)
P,C. LAYOUT
_ OF SWITCH
OF SWITCH/
7
>5±.g
°DIA. 5 HOLES
( I - 6 5 * ng) "
G-141 Double Pole/Four Position (with detent)
aS!S™««-4-H
,__.6S
^
(17.
TYPE
ELECTRICAL RATING
LISTING*
G-140-S
0.5Aat125Vac/Vdc
U.L.&C.S.A.
G-140-S-3
3.0Aac,0.5Aat125Vdc
U.L.&C.S.A.
G-140-S-6
6.0Aac,0.5Aat125Vdc
U.L.&C.S.A.
G-140-S-8.5
8.5Aac,0.5Aat125Vdc
U.L.&C.S.A.
'Specify C.S.A. listing, if required.
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper". See page 4.
BUTTONS
.200" (5.08 mm) button height shown is standard.
Other heights available are .125" (3.18 mm), .328"
(8.35 mm), and .453" (11.51 mm).
MOUNTING
PANEL—Two .100" diameter holes on 1.187" centers. 4-40
extruded and tapped holes are available.
PRINTED CIRCUIT BOARD—Plug directly into printed circuit board having hole pattern mating with your switch terminals. Standard G-140S single pole terminal orientation is IN
LINE. For greater switch stability on your PC board before
soldering, specify STAGGERED terminals.
TERMINALS
Standard is solder terminal G-20-28 as shown. For PC applications, we suggest G-20-18, but you may specify the terminal of your choice from those shown on page 15.
TYPE
G-141-S
G-141-S-3
G-141-S-6
G-141-S-8.5
G-141-L
G-141-L-3
G-141-L-6
G-141-L-8.5
ELECTRICAL RATING
0.5Aat125Vac/Vdc
3.0Aac,0.5Aat125Vdc
6.0Aac,0.5Aat125Vdc
8.5Aac, 0.5Aat125Vdc
0.5Aat125Vac/Vdc
3.0Aac,0.5Aat125Vdc
6.0Aac,0.5Aat125Vdc
8.5Aac,0.5Aat125Vdc
LISTING*
U.L.&C.S.A.
U.L.&C.S.A.
U.L.&C.S.A.
U.L.&C.S.A.
U.L.&C.S.A.
U.L.&C.S.A.
U.L.&C.S.A.
U.L.&C.S.A.
'Specify C.S.A. listing, if required.
.OI6_
1.41)
Drawing shows button in extreme right position where LONG
detent plate covers topside opening to the left of the button
and extends beyond (in blue) housing on right. Specify
G-141L with suffix indicating current requirement. If topside
opening need not be covered, specify G-141S with appropriate suffix.
10
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper". See page 4.
BUTTONS
.200" (5.08 mm) button height shown is standard.
Other heights available are .125" (3.18 mm), .328"
(8.33 mm), .453" (11.51 mm).
MOUNTING
PANEL—Two .100" diameter holes on 1.187" centers. 4-40
extruded and tapped holes are available.
PRINTED CIRCUIT BOARD—Plug directly into printed
circuit board having hole pattern shown.
TERMINALS
Standard is solder terminal G-20-28 as shown. For PC applications, we suggest G-20-18, but you may specify the terminal of your choice from those shown on page 15.
WUP INDUSTRIES 130 James Way, Southampton, PA 18966-3838 -Tel. 215-355-7080' Fax 215-355-1088 •www.cwind.com
SIDE-ACTUATED PANEL MOUNT MINIATURE SWIDGETS
GI-151 Single Pole/Double Throw (with detent)
GI-152 Double Pole/Double Throw (with detent)
I.OOO
(25.40)
M
8I2
tao.62)
1
1
j
,dbi£ ^h i
*H£"""^s
ELECTRICAL RATING
0.5Aat125Vac/Vdc
3.0Aac,0.5Aat125Vdc
LISTING*
U.L&C.S.A.
U.L&C.S.A.
ELECTRICAL RATING
TYPE
0.5Aat125Vac/Vdc
GI-152
3.0Aac,0.5Aat125Vdc
GI-152-3
'Specify C.S.A. listing, if required.
LISTING*
U.L&C.S.A.
U.L&C.S.A.
TYPE
GI-151
GI-151-3
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper". See page 12.
BUTTONS
.200" (5.08 mm) button length shown is standard.
Other lengths available are .328" (8.33 mm) and
.453" (11.51 mm).
MOUNTING
PANEL—Two .100" diameter holes on .812" centers. 4-40
extruded and tapped holes are also available.
PRINTED CIRCUIT BOARD—Plug directly into printed circuit board having hole pattern mating with your switch terminals. Standard single pole terminal orientation is IN-LINE.
For greater switch stability on your P.C. Board before soldering, specify STAGGERED terminals. For PC board mount,
we recommend use of mounting ears to supplement support
provided by terminals.
TERMINALS
Standard is G-20-28 terminal. Also available, if specified, are
terminals shown on page 15.
SOLDER SHIELD
Vulcanized fiber shield .020" thick may be shipped assembled or separate as requested.
GI-153 Single Pole/Three Position (with detent)
GI-154 Double PoleAThree Position (with detent)
M
U90
1.000
(25.40)
"
"o4fs'€ ili $
UJ
fif
U0°plA.2HOUS
U
L
.292±-oio
D.P.
*»»"TwJL]
tj£54f*
*
65
r•° ;B>,A.HOLETYR
l.65_-.oo)
D.P. P.C. LAYOUT-^,
INLINE P.C.LAYOUT^v
\1
STAGGERED
TYPE
GI-153
GI-153-3
TYPE
GI-154
GI-154-3
*Specify C.S.A.
ELECTRICAL RATING
0.5Aat125Vac/Vdc
3.0 A at 125 Vac
ELECTRICAL RATING
0.5Aat125Vac/Vdc
3.0Aac,0.5Aat125Vdc
listing, if required.
LISTING*
U.L&C.S.A.
U L &CS.A.
LISTING*
,
U L & C S.A.
U L & C.S.A.
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper". See page 12.
BUTTONS
.200" (5.08 mm) button length shown is standard.
Other lengths available are .328" (8.33 mm) and
.453" (11.51 mm).
MOUNTING
PANEL—Two .100" diameter holes on 1.000" centers. 4-40
extruded and tapped mounting holes are available.
PRINTED CIRCUIT BOARD—Plug directly into printed circuit board having hole pattern mating with your switch terminals. Standard single pole terminal orientation is IN LINE.
For greater switch stability on your PC board before soldering, specify STAGGERED terminals. For PC board mount,
we recommend use of mounting ears to supplement support
provided by terminals.
TERMINALS
Standard is G-20-28 terminal. Also available, if specified, are
terminals shown on page 15.
INDUSTRIES 130 James Way, Southampton, PA 18966-3838 -Tel. 215-355-7080* Fax 215-355-1088 •www.cwind.com
11
SIDE-ACTUATED PANEL MOUNT MINIATURE SWIDGETS
GF-165 Three Pole/Double Throw (with detent)
P.C. LAYOUT
ELECTRICAL RATING
LISTING*
U.L&C.S.A.
0.5Aat125Vac/Vdc
'Specify C.S.A. listing, if required.
BUTTONS
.200" (5.08 mm) button length shown is standard.
Other lengths available are .328" (8.33 mm), and .453"
(11.51 mm).
MOUNTING
PANEL—Two .100" diameter holes on .812" centers.
PRINTED CIRCUIT BOARD—Plug directly into PC board
having hole pattern shown. For PC board mount, we recommend use of mounting ears to supplement support provided
by terminals.
TERMINALS
Standard is solder terminal G-20-28 as shown. For PC applications, we suggest G-20-18, but you may specify the terminal of your choice from those shown on page 15.
SOLDER SHIELD
Vulcanized fiber shield .020" thick may be shipped assembled or separate as requested.
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper", as shown below.
.750
[19.051
.437 _
(11.10)
U
D
D
,
D
D
O
.
.032 ( .81)
.251 (6.38)
.115 (2.92)
G-02-331
(DIM "B")
Not recommended
.211 (5.36)
.075 (1.91)
D
O ,
GI-158 Single Pole/Four Position (with detent)
GI-159 Double Pole/Four Position (with detent)
12
G-02-56
W/TERMINAL
G-20-18
G-20-19
G-20-25
O
TYPE
ELECTRICAL RATING
LISTING*
GI-158
0.5Aat125Vac/Vdc
U.L&C.S.A.
GI-158-3
3.0Aac,0.5Aat125Vdc
U.L&C.S.A.
GI-159
0.5Aat125Vac/Vdc
U.L&C.S.A.
GI-159-3
3.0Aac,0.5Aat125Vdc
U.L&C.S.A.
'Specify C.S.A. listing, if required.
TOPPERS
Control panel styling and appearance can be changed by
adding an auxiliary "Topper". See above.
BUTTONS
.200" (5.08 mm) button length shown is standard.
Other lengths available are .328" (8.33 mm), and .453"
(11.51 mm).
MOUNTING
PANEL—Two. 100" diameter holes on 1.187" centers.
PRINTED CIRCUIT BOARD—Plug directly into printed circuit board having hole pattern mating with your switch terminals. Standard single pole terminal orientation is IN LINE.
For greater switch stability on your PC board before soldering, specify STAGGERED terminals. For PC board mount,
we recommend use of mounting ears to supplement support
provided by terminals.
TERMINALS
Standard is solder terminal G-20-28 as shown. For PC applications, we suggest G-20-18, but you may specify the terminal of your choice from those shown on page 15.
SOLDER SHIELD
Vulcanized fiber shield .020" thick may be shipped assembled or separate as requested.
INDUSTRIES 130 James Way, Southampton, PA 18966-3838 • Tel. 215-355-7080 • Fax 215-355-1088 • www.cwind.com
SIDE-ACTUATED PANEL MOUNT MINIATURE SWIDGETS
GI-163 Double Pole/Five Position (with detent)
TYPE
GI-163
GI-163-3
ELECTRICAL RATING
0.5Aat125Vac/Vdc
3.0Aac,0.5Aat125Vdc
LISTING*
U.L&C.S.A.
U.L&C.S.A.
*Specify C.S.A. listing, if required.
P.C. LAYOUT
5
fe^fe—I
工商网监
湘ICP备2023018690号
