BCM20737S

Please note that Cypress is an Infineon Technologies Company. The document following this cover page is marked as “Cypress” document as this is the company that originally developed the product. Please note that Infineon will continue to offer the product to new and existing customers as part of the Infineon product portfolio. Continuity of document content The fact that Infineon offers the following product as part of the Infineon product portfolio does not lead to any changes to this document. Future revisions will occur when appropriate, and any changes will be set out on the document history page. Continuity of ordering part numbers Infineon continues to support existing part numbers. Please continue to use the ordering part numbers listed in the datasheet for ordering. www.infineon.com CYW20737S Bluetooth Low Energy System-in-Package (SiP) Module The CYW20737S is a compact, highly integrated Bluetooth Low Energy (BLE) system-in-package (SiP) module. The CYW20737S SiP includes an embedded BLE antenna, 24 MHz clock, and 512 Kb EEPROM, so only a minimal set of external components is needed to create a standalone BLE device. The CYW20737S is designed to accelerate time to market. The Bluetooth stack and several application profiles are built into the module, allowing customers to focus on their core applications. To further reduce application development time, the CYW20737S includes integrated software support, with one-click installation of the complete environment and a one-click compile/build/link/load cycle. All this, coupled with an ultrasmall form factor and support for a wide voltage range, makes the CYW20737S well suited for virtually any Bluetooth Smart application. Cypress Part Numbering Scheme Cypress is converting the acquired IoT part numbers from Broadcom to the Cypress part numbering scheme. Due to this conversion, there is no change in form, fit, or function as a result of offering the device with Cypress part number marking. The table provides Cypress ordering part number that matches an existing IoT part number. Table 1. Mapping Table for Part Number between Broadcom and Cypress Broadcom Part Number Cypress Part Number BCM20737S CYW20737S Features Applications ■ ARM Cortex-M3 microcontroller unit (MCU) Profiles supported in ROM: ■ Embedded 512 Kb EEPROM ■ Battery status ■ Broadcom Serial Control (BSC), SPI, and UART interfaces ■ Blood pressure monitor ■ FCC and CE compliant ■ Find me ■ RoHS compliant, certified lead- and halogen-free ■ Heart rate monitor ■ Moisture Sensitivity Level (MSL) 3 compliant ■ Proximity ■ 6.5 mm × 6.5 mm × 1.2 mm Land Grid Array (LGA) 48-pin package ■ Thermometer ■ Weight scale ■ Time ■ Blood glucose monitor ■ Support for RSA security library ■ Support for LE Audio ■ Support for pairing using NFC tags Additional profiles supported in RAM: Cypress Semiconductor Corporation Document Number: 002-14888 Rev. *C • ■ Blood glucose monitor ■ Temperature alarm ■ Location ■ Other custom profiles 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised April 21, 2017 CYW20737S Figure 1. CYW20737S BLE SiP Block Diagram VBAT/VDDIO CYW20737S BCM20737S Antenna Bandpass Filter UART BCM20737S CYW20737S 24 MHz XTAL Bluetooth Low Energy System-on-Chip with ARM ® Cortex™ M3-based Microprocessor Core SPI/I2C Infrared ADC GPIOs PWM EEPROM 512 Kb I2C 32.768 kHz Oscillator (optional) IoT Resources Cypress provides a wealth of data at http://www.cypress.com/internet-things-iot to help you to select the right IoT device for your design, and quickly and effectively integrate the device into your design. Cypress provides customer access to a wide range of information, including technical documentation, schematic diagrams, product bill of materials, PCB layout information, and software updates. Customers can acquire technical documentation and software from the Cypress Support Community website (http://community.cypress.com/). Document Number: 002-14888 Rev. *C Page 2 of 24 CYW20737S Contents 1. Functional Description ................................................. 4 1.1 External Reset ....................................................... 4 1.2 32.768 kHz Oscillator ............................................ 4 2. Pin Map and Signal Descriptions ................................ 5 3. Electrical Specifications ............................................ 10 4. RF Specifications ....................................................... 11 5. ADC Specifications .................................................... 12 6. Timing and AC Characteristics ................................. 13 6.1 SPI Timing ........................................................... 13 6.2 BSC Interface Timing .......................................... 14 Document Number: 002-14888 Rev. *C 6.3 UART Timing ....................................................... 15 7. PCB Design and Manufacturing Recommendations 16 7.1 Pad and Solder Mask Opening Dimensions ........ 16 7.2 PCB Layout Recommendations .......................... 16 7.3 PCB Stencil ............................................................... 17 7.4 Solder Reflow ...................................................... 17 8. Packaging and Storage Information ......................... 18 9. Mechanical Information ............................................. 20 10. Ordering Information ................................................ 22 Document History .......................................................... 23 Page 3 of 24 CYW20737S 1. Functional Description 1.1 External Reset External reset timing for the CYW20737S is illustrated in Figure 2. Figure 2. External Reset Timing Pulse width >20 µs RESET_N Crystal  warm‐up  delay:  ~ 5 ms Baseband Reset Start reading EEPROM and  firmware boot Crystal Enable 1.2 32.768 kHz Oscillator The CYW20737S includes a standard Pierce oscillator. The oscillator circuit includes a comparator with hysteresis on the output to create a single-ended digital output. The hysteresis eliminates chatter when the input is near the comparator threshold (~100 mV). The oscillator circuit can is designed for a 32 kHz or 32.768 kHz crystal oscillator, and can also be driven by an external clock input with a similar frequency. Characteristics for a 32 kHz oscillator are defined in Table 2. Table 2. 32 kHz Crystal Oscillator Characteristics Parameter Output frequency Frequency tolerance Start-up time Crystal drive level Symbol Conditions Min. Typ. Max. Unit Foscout – – 32.768 – kHz – 100 – ppm – – 500 µs – µW Ftol Tstartup Crystal-dependent – Pdrv For crystal selection 0.5 – Crystal series resistance Rseries For crystal selection – – 70 kΩ Crystal shunt capacitance Cshunt For crystal selection – – 1.3 pF Document Number: 002-14888 Rev. *C Page 4 of 24 CYW20737S 2. Pin Map and Signal Descriptions The CYW20737S pin map is shown in Figure 3. Figure 3. CYW20737S (TOP View) The signal name, type, and description of each pin in the CYW20737S is listed in Table 3 on page 6. The symbols shown under I/O Type indicate pin directions (I/O = bidirectional, I = input, O = output) and the internal pull-up/pull-down characteristics (PU = weak internal pull-up resistor and PD = weak internal pull-down resistor), if any. Document Number: 002-14888 Rev. *C Page 5 of 24 CYW20737S Table 3. Pin Descriptions Pin Name I/O Type Description 1 GPIO: P27 PWM1 I 2 GND GND 3 VBAT I 4 GND GND GND 5 GND GND GND 6 GND GND GND 7 GND GND GND 8 GND GND GND 9 GND GND GND 10 Reserved – 11 GND GND GND 12 GND GND GND 13 GND GND GND 14 GND GND GND 15 GND GND GND 16 GND GND GND 17 GND GND GND 18 UART_RX I 19 UART_TX O, PU UART_TX 20 GND GND GND 21 SCL I/O, PU SCL I/O, PU clock signal for an external I2C device 22 SDA I/O, PU SDA I/O, PU data signal for an external I2C device 23 GND GND GND 24 GND GND GND Default direction: Input. After POR state: Input floating. Drain current: 16 mA Alternate function: MOSI (master and slave) for SPI_2 GND Battery supply input. Leave floating UART_RX. This pin is pulled low through an internal 10 kΩ resistor. 25 GPIO: P1 I Default direction: Input. After POR state: Input floating. This pin is tied to the WP pin of the embedded EEPROM. Requires an external 10K pull-up 26 TMC I Test mode control. Pull this pin high to invoke test mode; leave it floating if not used. This pin is connected to GND through an internal 10 kΩ resistor. 27 RESET_N I/O PU Document Number: 002-14888 Rev. *C Active-low system reset with open-drain output Page 6 of 24 CYW20737S Table 3. Pin Descriptions (Cont.) Pin Name I/O Type Description Default direction: Input. After POR state: Input floating. Alternate functions: 28 29 30 GPIO: P0 GND GPIO: P3 I GND I ■ A/D converter input ■ Peripheral UART TX (PUART_TX) ■ MOSI (master and slave) for SPI_2 ■ IR_RX ■ 60Hz_main GND Default direction: Input. After POR state: Input floating. Alternate functions: ■ Peripheral UART CTS (PUART_CTS) ■ SPI_CLK (master and slave) for SPI_2 Default direction: Input. After POR state: Input floating. Alternate functions: 31 GPIO: P2 I ■ Peripheral UART RX (PUART_RX) ■ SPI_CS (slave only) for SPI_2 ■ SPI_MOSI (master only) for SPI_2 Default direction: Input. After POR state: Input floating. Alternate functions: 32 33 GPIO: P4 GPIO: P8 I I ■ Peripheral UART RX (PUART_RX) ■ MOSI (master and slave) for SPI_2. ■ IR_TX Default direction: Input. After POR state: Input floating. Alternate functions: A/D converter input. Default direction: Input. After POR state: Input floating. Alternate functions: 34 GPIO: P33 I Document Number: 002-14888 Rev. *C ■ A/D converter input ■ MOSI (slave only) for SPI_2 ■ Auxiliary clock output (ACLK1) ■ Peripheral UART RX (PUART_RX) Page 7 of 24 CYW20737S Table 3. Pin Descriptions (Cont.) Pin Name I/O Type Description Default direction: Input. After POR state: Input floating. Alternate functions: 35 36 37 38 GPIO: P32 GPIO: P25 GPIO: P24 NC GPIO: P13 PWM3 I I I NC I 39 GPIO: P28 PWM2 GPIO: P14 PWM2 I I ■ A/D converter input ■ SPI_CS (slave only) for SPI_2. ■ Auxiliary clock output (ACLK0) ■ Peripheral UART TX (PUART_TX) Default direction: Input. After POR state: Input floating. Alternate functions: ■ MISO (master and slave) for SPI_2 ■ Peripheral UART RX (PUART_RX) Default direction: Input. After POR state: Input floating. Alternate functions: ■ SPI_CLK (master and slave) for SPI_2 ■ Peripheral UART TX (PUART_TX) No Connection (N/C). Default Direction: Input After POR State: Input Floating Drain current: 16 mA Alternate function: A/D converter input Default direction: Input. After POR state: Input floating. Drain current: 16 mA Alternate functions: ■ A/D converter input ■ LED1 ■ IR_TX Default direction: Input. After POR state: Input floating. Alternate function: A/D converter input Default direction: Input. After POR state: Input floating. Alternate functions: 40 GPIO: P38 I ■ A/D converter input ■ MOSI (master and slave) for SPI_2 ■ IR_TX Default direction: Input. After POR state: Input floating. Alternate functions: 41 GPIO: P15 I Document Number: 002-14888 Rev. *C ■ A/D converter input ■ IR_RX ■ 60 Hz_main Page 8 of 24 CYW20737S Table 3. Pin Descriptions (Cont.) Pin Name I/O Type 42 GPIO: P26 PWM0 I GPIO: P12 I 43 XTALO32K GPIO: P11 O I 44 Description Default direction: Input. After POR state: Input floating. Drain current: 16 mA Alternate function: SPI_CS (slave only) for SPI_2 Default direction: Input. After POR state: Input floating. Alternate functions: ■ A/D converter input ■ XTALO32K Low-power oscillator (LPO) output. Alternate functions: P12 P26 Default direction: Input. After POR state: Input floating. Alternate functions: ■ A/D converter input ■ XTALI32K Low-power oscillator (LPO) input. Alternate functions: XTALI32K I ■ P11 ■ P27 45 GND GND GND 46 GND GND GND 47 GND GND GND 48 GND GND GND Document Number: 002-14888 Rev. *C Page 9 of 24 CYW20737S 3. Electrical Specifications Absolute maximum ratings are defined in Table 4. Table 4. Absolute Maximum Ratings Min. Max. Unit Supply power Parameter NA 3.63 V Storage temperature –40 125 °C 0 ±2 % 1.62 3.63 V Voltage ripple Power supply (VBAT absolute maximum rating) Power for the CYW20737S module is provided by the host through the power pins. Table 5. Voltage Symbol Parameter VBAT Battery voltage Min. Typ. Max. Unit 1.62 – 3.63 V Table 6. Current Consumption Nominal Maximum Unit Receive Operating Mode Receiver and baseband are both operating, 100% Condition 24.0 28.0 mA Transmit Transmitter and baseband are both operating, 100% 24.0 28.0 mA Sleep Wake in < 5 ms 55.0 60.0 µA Deep Sleep Wake on interrupt 2.0 2.5 µA Note: All measurements taken at 25°C Based on the current measurements in Table 6 on page 10, CYW20737S peak power values are: ■ RX: 101.6 mW ■ TX: 101.6 mW ■ Sleep mode: 217.8 µW ■ Deep Sleep mode: 9.1 µW Document Number: 002-14888 Rev. *C Page 10 of 24 CYW20737S 4. RF Specifications CYW20737S receiver specifications are defined in Table 7. Table 7. Receiver Specifications Parameter Mode and Conditions Min. Typ. Max. Unit – 2402 – 2480 MHz – –94 – dBm –10 – – dBm Frequency range RX sensitivity (standard) Packets: 200 Payload: PRBS 9 Length: 37 Bytes Dirty Transmitter: off. PER: 30.8% Maximum input – Note: All measurements taken at 3.0V (default voltage) RF transmitter specifications are defined in Table 8. Table 8. Transmitter Specifications Parameter Min. Typ. Max. Unit Transmitter Frequency rangea 2402 – 2480 MHz Output power adjustment range –20 – 4 dBm Output power – 2 – dBm Output power variation – 2.5 – dB – – ±150 kHz – – ±50 kHz – – 20 kHz/50 µs Average deviation in payload (sequence: 00001111) 225 – 275 kHz Average deviation in payload (sequence: 10101010) 185 – – kHz – 2 – MHz LO Performance Initial carrier frequency tolerance Frequency Drift Frequency drift Drift rate Frequency Deviation Channel spacing a. This parameter is taken from the Bluetooth 4.0 specification. Document Number: 002-14888 Rev. *C Page 11 of 24 CYW20737S 5. ADC Specifications CYW20737S ADC specifications are defined in Table 9. Table 9. ADC Specifications Parameter Symbol Conditions Min. Typ. Max. Unit Number of input channels – – – 9 – - Channel switching rate fch – – – 133.33 Kch/s Input signal range Reference settling time Vinp – – Charging refsel 0 – 3.63 V 7.5 – – µs – 500 – kΩ – 5 pF Input resistance Rinp Input capacitance Cinp – – Conversion rate Fc – 5.859 – 187 kHz Conversion time Tc – 5.35 – 170.7 µs Resolution R – Absolute voltage measurement error – Using on–chip ADC firmware driver Current I Iavdd1p2 + Iavdd3p3 Power P Leakage Current Ileakage Power-up time Tpowerup Effective, single-ended – T = 25°C – 16 – Bits ±2 – % – – 1 mA – 1.5 – mW – – 100 nA – – 200 µs Integral nonlinearity INL In the guaranteed performance range –1 – 1 LSBa Differential nonlinearity DNL In the guaranteed performance range –1 – 1 LSBa a. LSBs are expressed at the 10-bit level. Document Number: 002-14888 Rev. *C Page 12 of 24 CYW20737S 6. Timing and AC Characteristics 6.1 SPI Timing SPI interface timing is illustrated in Figure 4 and Figure 5 and defined in Table 10 on page 14. Figure 4. SPI Timing—Modes 0 and 2 6 SPI_CSN SPI_CLK (Mode 0) 1 SPI_CLK (Mode 2) 2 ‐ SPI_MOSI First Bit 3 Second Bit 4 SPI_MISO Not Driven First Bit Last bit ‐ Last bit Not Driven 5 Second Bit Figure 5. SPI Timing—Modes 1 and 3 6 SPI_CSN SPI_CLK (Mode 1) 1 SPI_CLK (Mode 3) 2 SPI_MOSI ‐ Invalid bit 3 First bit 4 SPI_MISO Not Driven Invalid bit Document Number: 002-14888 Rev. *C First bit Last bit ‐ Last bit Not Driven 5 Page 13 of 24 CYW20737S Table 10. SPI Interface Timing Specifications Reference Characteristics Min. Typ. Max. 1 Time from CSN asserted to first clock edge 1 SCK 100 ∞ 2 Master setup time – 1/2SCK – 3 Master hold time 1/2SCK - – 4 Slave setup time – 1/2 SCK – 5 Slave hold time 1/2 SCK – – 6 Time from last clock edge to CSN deasserted SCK 10 SCK 100 6.2 BSC Interface Timing BSC interface timing is illustrated in Figure 6 and is defined in Table 11. Figure 6. BSC Interface Timing Table 11. BSC Interface Timing Specifications Reference 1 Characteristics Clock frequency Min. Max. Unit – 100, 400, 800, 1000 kHz 2 START condition setup time 650 – ns 3 START condition hold time 280 – ns 4 Clock low time 650 – ns 5 Clock high time 280 – ns 6 Data input hold time 0 – ns 7 Data input setup time 100 – ns 8 STOP condition setup time 280 – ns 9 Output valid from clock – 400 ns 10 Bus free time 650 – ns Document Number: 002-14888 Rev. *C Page 14 of 24 CYW20737S 6.3 UART Timing UART timing is illustrated in Figure 7 and defined in Table 12. Figure 7. UART Timing Table 12. UART Timing Specifications Reference Characteristics Min. Max. Unit 1 Delay time, UART_CTS_N low to UART_TXD valid – 24 Baudout cycles 2 Setup time, UART_CTS_N high before midpoint of stop bit – 10 ns 3 Delay time, midpoint of stop bit to UART_RTS_N high – 2 Baudout cycles Document Number: 002-14888 Rev. *C Page 15 of 24 CYW20737S 7. PCB Design and Manufacturing Recommendations 7.1 Pad and Solder Mask Opening Dimensions CYW20737S pad and solder mask opening dimensions are defined in Table 13. Table 13. Pad and Solder Mask Dimensions Pad Type Pad Dimensions Solder Mask Opening Dimensions Type A 0.6 × 0.25 0.7 × 0.35 Type B 0.55 × 0.3 0.65 × 0.4 Type C 0.4 × 0.4 0.5 × 0.5 Unit mm 7.2 PCB Layout Recommendations The following layout recommendations are referenced to Figure 8 on page 16. ■ Connect to system ground from side D of the module (pins 13–22). ■ The L-shaped ground plane is required for the embedded BLE antenna. Keep the GND continuous. Do not cut off the GND shape to accommodate trace routes. ■ An L-shaped ground plane is required. If the L-shaped GND plane is located on the top layer of the PCB, do not place components on the ground plane. If this cannot be avoided, move the L-shaped ground plane to another layer. ■ Antenna efficiency of 31–41% can be achieved based on the layout in Figure 8 on page 16 and the dimensions listed below. Following these layout recommendations is expected to yield 50+ meters of usable range; deviating from these recommendations may reduce the range of the antenna. ❐ D: 4.5 mm (typical) ❐ G, H, S: 3 mm (typical) ❐ L: 3 mm (minimum) ❐ W: 0.4 mm (typical) ■ Route signal traces out of the module from side C (between pins 27 and 30) or side D (between pins 16 and 19) of the module. Traces can be overlapped to avoid routing through the keep-out area. ■ Do not route traces from side A or side B. Figure 8. PCB Layout Example Document Number: 002-14888 Rev. *C Page 16 of 24 CYW20737S 7.3 PCB Stencil The recommended PCB stencil is shown in Figure 9 (all measurements in mm). Use an unsolder mask to set the module footprint. Figure 9. CYW20737S Stencil (Bottom View) 7.4 Solder Reflow The recommended solder reflow profile for the CYW20737S is defined in Figure 10. Figure 10. Solder Reflow Profile 245°C Temperature 217°C 200°C 150°C Pre‐Heating: 90~120 sec. Soldering: 60~90 sec. Ti Document Number: 002-14888 Rev. *C Page 17 of 24 CYW20737S 8. Packaging and Storage Information The CYW20737S is available in a tape and reel package and is shipped in an ESD-protected moisture-resistant (MSL-3) bag as shown in Figure 11. The storage temperature range is –40°C to +125°C. Figure 11. CYW20737S ESD/Moisture Packaging The moisture sensitivity label on the CYW20737S shipping bag is shown in Figure 12 on page 19. Document Number: 002-14888 Rev. *C Page 18 of 24 CYW20737S Figure 12. CYW20737S Moisture Sensitivity Label Figure 13 shows the location of pin 1 on the CYW20737S relative to its orientation on the tape packaging. Figure 13. CYW20737S Tape and Reel Pin 1 Location Document Number: 002-14888 Rev. *C Page 19 of 24 CYW20737S 9. Mechanical Information Package dimensions for the CYW20737S are shown in Figure 14. Figure 14. CYW20737S Package Dimensions Additional CYW20737S package dimensions are shown in Figure 15 on page 21. Document Number: 002-14888 Rev. *C Page 20 of 24 CYW20737S Figure 15. CYW20737S Pin Dimensions (Bottom View) Document Number: 002-14888 Rev. *C Page 21 of 24 CYW20737S 10. Ordering Information Table 14. Ordering Information Part Number CYW20737S Document Number: 002-14888 Rev. *C Package Operating Temperature 48-pin LGA –40°C to +85°C Humidity 95% max., noncondensing Page 22 of 24 CYW20737S Document History Document Title: CYW20737S Bluetooth Low Energy System-in-Package (SiP) Module Document Number: 002-14888 Revision ECN Orig. of Change Submission Date ** – – 09/26/2014 20737S-DS100-R: Initial release *A – UTSV 11/06/2015 20737S-DS101-R: Updated • Table 5 on page 14 *B 5444054 UTSV 09/23/2016 *C 5688156 AESATMP7 04/21/2017 Document Number: 002-14888 Rev. *C Description of Change Updated to Cypress Template Updated Cypress Logo and Copyright. Page 23 of 24 CYW20737S Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC®Solutions Products ARM® Cortex® Microcontrollers Automotive cypress.com/arm cypress.com/automotive Clocks & Buffers Interface cypress.com/clocks cypress.com/interface Internet of Things Memory cypress.com/iot cypress.com/memory Microcontrollers cypress.com/mcu PSoC cypress.com/psoc Power Management ICs Cypress Developer Community Forums | WICED IoT Forums | Projects | Video | Blogs | Training | Components Technical Support cypress.com/support cypress.com/pmic Touch Sensing cypress.com/touch USB Controllers Wireless Connectivity PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 cypress.com/usb cypress.com/wireless 24 © Cypress Semiconductor Corporation, 2014-2017. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC (“Cypress”). This document, including any software or firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage (“Unintended Uses”). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. Document Number: 002-14888 Rev. *C Revised April 21, 2017 Page 24 of 24