CY2XP24
Crystal to LVPECL Clock Generator
Features
■ ■ ■ ■ ■ ■ ■
Functional Description
The CY2XP24 is a PLL (phase locked loop) based high performance clock generator. It is optimized to generate 10 Gb Ethernet, Fibre Channel, and other high performance clock frequencies. It produces an output frequency that is either 6.25 times or 7.5 times the crystal frequency. It uses Cypress’s low noise VCO technology to achieve low phase jitter, that meets both 10 Gb Ethernet, Fibre Channel, and SATA jitter requirements. The CY2XP24 has a crystal oscillator interface input and one LVPECL output pair.
One LVPECL Output Pair Selectable output frequency: 156.25 MHz or 187.5 MHz External crystal frequency: 25 MHz Low root mean square (RMS) phase jitter at 156.25 MHz, using 25 MHz crystal (1.875 MHz to 20 MHz): 0.33 ps (typical) Pb-free 8-Pin thin shrunk small outline package (TSSOP) Package Supply voltage: 3.3 V or 2.5 V Commercial and industrial temperature ranges
Logic Block Diagram
XIN External Crystal XOUT 0 = /25 1 = /30 F_SEL CRYSTAL OSCILLATOR PHASE DETECTOR VCO /4 CLK CLK#
Cypress Semiconductor Corporation Document #: 001-15705 Rev. *G
•
198 Champion Court
•
San Jose, CA 95134-1709
• 408-943-2600 Revised April 7, 2011
[+] Feedback
CY2XP24
Contents
Pinouts .............................................................................. 3 Frequency Table ............................................................... 4 Absolute Maximum Conditions ....................................... 4 Operating Conditions ....................................................... 4 DC Electrical Characteristics .......................................... 4 AC Electrical Characteristics ........................................... 5 Recommended Crystal Specifications ............................ 5 Parameter Measurements ................................................ 6 Application Information ................................................... 7 Power Supply Filtering Techniques ............................. 7 Termination for LVPECL Output .................................. 7 Crystal Input Interface ................................................. 7 Ordering Information ........................................................ 8 Ordering Code Definition ............................................. 8 Acronyms ........................................................................ 10 Document Conventions ................................................. 10 Units of Measure ....................................................... 10 Sales, Solutions, and Legal Information ...................... 12 Worldwide Sales and Design Support ....................... 12 Products .................................................................... 12 PSoC Solutions ......................................................... 12
Document #: 001-15705 Rev. *G
Page 2 of 12
[+] Feedback
CY2XP24
Pinouts
Figure 1. Pin Diagram - 8 Pin TSSOP
VDD VSS XOUT XIN
1 2 3 4
8 7 6 5
VDD CLK CLK# F_SEL
Table 1. Pin Definitions - 8 Pin TSSOP Pin 1, 8 2 3, 4 5 Name VDD VSS XOUT, XIN F_SEL Power Power XTAL output and input CMOS input Type Ground Parallel resonant crystal interface Frequency select. When HIGH, the output frequency is 7.5 times of the crystal frequency. When LOW, the output frequency is 6.25 times of the crystal frequency Differential clock output Description 3.3 V or 2.5 V power supply. All supply current flows through pin 1
6,7
CLK#, CLK
LVPECL output
Document #: 001-15705 Rev. *G
Page 3 of 12
[+] Feedback
CY2XP24
Frequency Table
Inputs Crystal Frequency (MHz) 25 25 F_SEL 1 0 PLL Multiplier Value 7.5 6.25 Output Frequency (MHz) 187.5 156.25
Absolute Maximum Conditions
Parameter VDD VIN[1] TS TJ ESDHBM UL–94 JA[2] Description Supply voltage Input voltage, DC Temperature, vtorage Temperature, junction ESD protection (human body model) Flammability rating Thermal resistance, junction to ambient JEDEC STD 22-A114-B At 1/8 in. 0 m/s airflow 1 m/s airflow 2.5 m/s airflow Relative to VSS Non operating Condition – Min –0.5 –0.5 –65 – 2000 V–0 100 91 87 C / W Max 4.4 VDD + 0.5 150 135 – Unit V V C C V
Operating Conditions
Parameter VDD TA TPU 3.3 V supply voltage 2.5 V supply voltage Ambient temperature, commercial Ambient temperature, industrial Power-up time for all VDD to reach minimum specified voltage (ensure power ramps are monotonic) Description Min 3.135 2.375 0 -40 0.05 Max 3.465 2.625 70 85 500 Unit V V C C ms
DC Electrical Characteristics
Parameter IDD Description Test Conditions Min – – – – Typ – – – – – – – Max 125 120 150 145 VDD –0.75 VDD –1.625 1000 Unit V V V V V V mV Power supply current with output VDD = 3.465 V, FOUT = 187.5 MHz, unterminated output unterminated VDD = 2.625 V, FOUT = 187.5 MHz, output unterminated IDDT Power supply current with output VDD = 3.465 V, FOUT = 187.5 MHz, terminated output terminated VDD = 2.625V, FOUT = 187.5 MHz, output terminated VOH VOL VOD1 LVPECL output high voltage LVPECL output low voltage LVPECL Peak-to-peak output voltage swing
VDD = 3.3 V or 2.5 V, RTERM = 50 to VDD –1.15 VDD – 2.0 V VDD = 3.3 V or 2.5 V, RTERM = 50 to VDD –2.0 VDD – 2.0 V VDD = 3.3 V or 2.5 V, RTERM = 50 to VDD – 2.0 V 600
Note 1. The voltage on any input or I/O pin cannot exceed the power pin during power up. Power supply sequencing is NOT required. 2. Simulated using Apache Sentinel TI software. The board is derived from the JEDEC multilayer standard. It measures 76 x 114 x 1.6 mm and has 4-layers of copper (2/1/1/2 oz.). The internal layers are 100% copper planes, while the top and bottom layers have 50% metalization. No vias are included in the model.
Document #: 001-15705 Rev. *G
Page 4 of 12
[+] Feedback
CY2XP24
DC Electrical Characteristics (continued)
Parameter VOD2 VOCM VIH VIL IIH IIL CIN
[3]
Description LVPECL output voltage swing (VOH - VOL) LVPECL output common mode voltage (VOH + VOL)/2 Input high voltage Input low voltage Input high current Input low current Input capacitance, F_SEL Pin capacitance, XIN & XOUT
Test Conditions VDD = 2.5 V, RTERM = 50 to VDD – 1.5 V VDD = 2.5 V, RTERM = 50 to VDD – 1.5 V
Min 500 1.2 0.7 x VDD –0.3
Typ – – – – – – 15 4.5
Max 1000 – VDD + 0.3 0.3 x VDD 115 – – –
Unit mV V V V µA µA pF pF
F_SEL = VDD F_SEL = VSS
– –50 – –
CINX[3]
AC Electrical Characteristics[4]
Parameter FOUT TR, TF[5] TJitter() TDC[7] TLOCK TLFS
[6]
Description Output frequency Output rise/fall time RMS phase jitter (random) Duty cycle Startup time
Conditions 20 % to 80 % of full swing 156.25 MHz, (1.875 – 20 MHz), 3.3 V 156.25 MHz, (12 kHz – 20 MHz), 3.3 V Measured at zero crossing point Time for CLK to reach valid frequency measured from the time VDD = VDD(min.) Time for CLK to reach valid frequency from F_SEL pin change
Min 156.25 – – – 45 –
Typ – 0.5 0.33 0.6 – –
Max 187.5 1.0 – – 55 5
Unit MHz ns ps ps % ms
Re-lock time
–
–
1
ms
Recommended Crystal Specifications[7]
Parameter Mode F ESR C0 Mode of oscillation Frequency Equivalent series resistance Shunt capacitance Description Min 25 – – Max 25 50 7 Unit MHz pF Fundamental
Notes 3. Not 100% tested, guaranteed by design and characterization. 4. Characterized using an 18 pF parallel resonant crystal. 5. Refer to Figure 7 on page 7. 6. Refer to Figure 4 on page 4. 7. Refer to Figure 7 on page 7.
Document #: 001-15705 Rev. *G
Page 5 of 12
[+] Feedback
CY2XP24
Parameter Measurements
Figure 2. 3.3 V Output Load AC Test Circuit
2V VDD LVPECL VSS Z = 50 SCOPE CLK 50 Z = 50 CLK# 50 -1.3V +/- 0.165V
Figure 3. 2.5 V Output Load AC Test Circuit
2V VDD LVPECL VSS Z = 50 SCOPE CLK 50 Z = 50 CLK# 50 -0.5V +/- 0.125V
Figure 4. Output DC Parameters
CLK VOD CLK#
VA VOCM = (V A + VB)/2 VB
Figure 5. Output Rise and Fall Time
CLK#
20% TR TF 80% 80% 20%
CLK
Figure 6. RMS Phase Jitter
Phase noise
Noise Power Phase noise mark
Offset Frequency f1 RMS Jitter = f2 Area Under the Masked Phase Noise Plot
Document #: 001-15705 Rev. *G
Page 6 of 12
[+] Feedback
CY2XP24
Figure 7. Output Duty Cycle
CLK TDC = CLK# TPW TPERIOD TPW TPERIOD
Application Information
Power Supply Filtering Techniques
As in any high speed analog circuitry, noise at the power supply pins can degrade performance. To achieve optimum jitter performance, use good power supply isolation practices. Figure 8 illustrates a typical filtering scheme. Because all current flows through pin 1, the resistance and inductance between this pin and the supply is minimized. A 0.01 or 0.1 µF ceramic chip capacitor is also located close to this pin to provide a short and low impedance AC path to ground. A 1 to 10 µF ceramic or tantalum capacitor is located in the general vicinity of this device and may be shared with other devices. Figure 8. Power Supply Filtering
V DD (Pin 8) 3.3V F 0.01 µF 10µF
Figure 9. LVPECL Output Termination
3.3V
125 Z0 = 50
125
CLK
Z0 = 50 84 84 IN
CLK#
Crystal Input Interface
The CY2XP24 is characterized with 18 pF parallel resonant crystals. The capacitor values shown in Figure 10 are determined using a 25 MHz 18 pF parallel resonant crystal and are chosen to minimize the ppm error. Note that the optimal values for C1 and C2 depend on the parasitic trace capacitance and are therefore layout dependent. Figure 10. Crystal Input Interface
XIN
VDD (Pin 1)
Termination for LVPECL Output
The CY2XP24 implements its LVPECL driver with a current steering design. For proper operation, it requires a 50 ohm dc termination on each of the two output signals. For 3.3 V operation, this data sheet specifies output levels for termination to VDD–2.0 V. This termination voltage can also be used for VDD = 2.5 V operation, or it can be terminated to VDD-1.5 V. Note that it is also possible to terminate with 50 ohms to ground (VSS), but the high and low signal levels differ from the data sheet values. Termination resistors are best located close to the destination device. To avoid reflections, trace characteristic impedance (Z0) should match the termination impedance. Figure 9 shows a standard termination scheme.
X1 18 pF Parallel Crystal
C1 30 pF
Device
XOUT C2 27 pF
Document #: 001-15705 Rev. *G
Page 7 of 12
[+] Feedback
CY2XP24
Ordering Information
Part Number CY2XP24ZXC CY2XP24ZXCT CY2XP24ZXI CY2XP24ZXIT 8-Pin TSSOP 8-Pin TSSOP–Tape and Reel 8-Pin TSSOP 8-Pin TSSOP–Tape and Reel Package Type Product Flow Commercial, 0 C to 70 C Commercial, 0 C to 70 C Industrial, -40 C to 85 C Industrial, -40 C to 85 C
Ordering Code Definition
CY xx xxxx Z X C/I T
T = Tape and Reel Temperature Range: C = Commercial, I = Industrial Pb-free Package Type Part Identifier Family Company ID: CY = Cypress
Document #: 001-15705 Rev. *G
Page 8 of 12
[+] Feedback
CY2XP24
Package Drawing and Dimensions
Figure 11. 8-Pin Thin Shrunk Small Outline Package (4.40 MM Body) Z8
51-85093 *C
Document #: 001-15705 Rev. *G
Page 9 of 12
[+] Feedback
CY2XP24
Acronyms
Acronym CLKOUT CMOS DPM EPROM LVDS LVPECL NTSC OE PAL PD PLL PPM TTL Clock output Complementary metal oxide semiconductor Die pick map Erasable programmable read only memory Low-voltage differential signaling Low voltage positive emitter coupled logic National television system committee Output enable Phase alternate line Power down Phase locked loop Parts per million Transistor transistor logic Description
Document Conventions
Units of Measure
Symbol °C kHz k MHz M µA µs µV µVrms mA mm ms mV nA ns nV kilohertz kilohms megahertz megaohms microamperes microseconds microvolts microvolts root-mean-square milliamperes millimeters milliseconds millivolts nanoamperes nanoseconds nanovolts ohms Unit of Measure degrees Celsius
Document #: 001-15705 Rev. *G
Page 10 of 12
[+] Feedback
CY2XP24
Document History Page
Document Title: CY2XP24 Crystal to LVPECL Clock Generator Document Number: 001-15705 Rev. ** *A *B ECN No. 1285703 1451704 2669117 Submission Date See ECN See ECN 03/05/2009 Orig. of Change WWZ/KVM/ New data sheet ARI WWZ/AESA Added I-temp devices KVM/AESA Changed crystal frequency and output frequencies Updated phase jitter value Rise & fall times changed from 350 ps to 500 ps (typ.) Junction temperature changed from 125C to 135C Changed IIL and IIH values Entered value for IDD Removed MSL spec Changed Data Sheet Status to Final KVM/PYRS Typos: changed VCC to VDD, changed ps to MHz Changed footnote about external power dissipation Reformatted AC and DC tables Changed LVPECL parameters from VPP to VOD and VOCM Added CINX spec Added IDD for 2.5V Added TLOCK timing Revised text in Application Information section Changed recommended crystal load capacitor values WWZ/HMT No change. Submit to ECN for product launch. KVM Add phase jitter spec for 12 kHz - 20 MHz integration range Add IDD spec for unterminated outputs Change parameter name for IDD (terminated outputs) from IDD to IDDT Remove IDD footnote about externally dissipated current Add footnote reference to CIN and CINX:not 100% tested Add max limit for TR, TF: 1.0 ns Change TLOCK max from 10 ms to 5 ms Split out parameter TLFS from TLOCK Updated Package Diagram (Figure 11) Updated as per template Added Acronyms and Units of Measure table Added Ordering Code Definition details Updated package diagram 51-85093 from *B to *C Description of Change
*C
2700242
04/30/2009
*D *E
2718433 2767308
06/12/2009 09/22/2009
*F *G
2896121 3218841
03/19/2010 03/07/2011
KVM BASH
Document #: 001-15705 Rev. *G
Page 11 of 12
[+] Feedback
CY2XP24
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations.
Products
Automotive Clocks & Buffers Interface Lighting & Power Control Memory Optical & Image Sensing PSoC Touch Sensing USB Controllers Wireless/RF cypress.com/go/automotive cypress.com/go/clocks cypress.com/go/interface cypress.com/go/powerpsoc cypress.com/go/plc cypress.com/go/memory cypress.com/go/image cypress.com/go/psoc cypress.com/go/touch cypress.com/go/USB cypress.com/go/wireless
PSoC Solutions
psoc.cypress.com/solutions PSoC 1 | PSoC 3 | PSoC 5
© Cypress Semiconductor Corporation, 2010-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement.
Document #: 001-15705 Rev. *G
Revised April 7, 2011
Page 12 of 12
All products and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback