CY3699

CY3672 PTG Programming Kit Features • Supports Field-programmable Clock Generators • CY2077FS, CY2077FZ, CY22050F, CY22150F, CY22381F, CY22392F, CY22393F, CY22394F, CY22395F, CY25100F, CY25200F, CY25701F,CY25702F CY23FP12, CY26049, and CY27EE16 • Allows quick and easy prototyping • Compact design for ease of portability • Easy to use Microsoft® Windows® 95, 98, NT, 2K, ME, XP-compatible interface • User-friendly CyberClocks™ or CyberClocks Online software for JEDEC file development Functional Description The CY3672 programming kit enables any user with a PC to quickly and easily program Field-programmable Clock Generators. The only set-up requirements are a power connection and either a parallel port or USB port (CY3672-USB) connection with the PC, as shown in Figure 2. Using CyClocksRT™, (embedded in CyberClocks software) or CyberClocks Online, users can configure their parts to a given specification and generate the corresponding JEDEC file. In addition, CyClocksRT software provides PPM optimization and power calculations. The JEDEC file is then loaded into CY3672 software that communicates with the programmer. The CY3672 software has the ability to read and view the EPROM table from a programmed device. The programming flow is outlined in Figure 1. CY3672-PRG Kit Contents • Parallel port cable • AC/DC adapter • Quick start guide • User manual Set Up Hardware The CY3672 programming kit has a very simple set-up procedure. As shown in Figure 2, only two connections are required. The programmer must be connected to a PC through either a parallel port or USB port (CY3672-USB) and must receive power through the AC/DC adapter that gets hooked up to your standard 110V/220V wall outlet. When using the parallel port, make sure the parallel port settings on your computer is ECP or EPP. CY3672-PRG or CY3672-USB are the programming base unit that can be ordered separately with any individual socket adapter. CY3672-FTG Development Kit Contents in Addition to CY3672-PRG Contents • Three Sockets: CY3695, CY3698, CY3699 CY3672-USB Kit Contents in Addition to CY3672-PRG Contents • USB Driver CD ROM • USB Cable C y C lo c k s R T C Y 3 6 7 2 S o ftw a re P ro g ram m e r C Y 36 72 A d a p ter C y b e rC lo c k s O n lin e Jedec F ile B it S tre a m Figure 1. Programming Procedure Cypress Semiconductor Corporation Document #: 38-07409 Rev. *F • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised October 31, 2005 CY3672 Wall Power Adapter PC with Parallel Port Parallel Cable CY3672 Adapter Figure 2. CY3672 Programming Kit Set-up Figure 2 is a close-up of the socket and illustrates the correct orientation for placing the device into the socket. Pin1 should always be in the lower left corner, as shown in Figure 3. CyberClocks Online, which is a web based software, is available on-line through user registration. It configures spread spectrum clock generators, such as CY25100. To install the CY3672 software, first run SETUP.EXE to install necessary DLLs to the windows registry. Once this is done, run CY3672*.EXE to launch. When the CY3672 programmer is used for the first time, it is required to be in “TYPE” mode. This mode is set by pushing the arrow keys on the programmer until you see “TYPE” displayed on the LCD screen. Software Setting up the software is just as easy as setting up the hardware. Download the latest revisions of CyberClocks and CY3672 programmer software off of our web site at www.cypress.com. To install CyberClocks, unzip the file, then simply run the set-up file in the CyberClocks folder. It will prompt the user for a few questions and then self-installs.[1] Figure 3. Device Orientation Note: 1. Be sure to check for software updates at http://www.cypress.com/support. Document #: 38-07409 Rev. *F Page 2 of 6 CY3672 Quick Start Guide Go through the following steps to properly configure and use the CY3672. 1. a. If you are using a parallel port, make sure your parallel port setting is ECP or EPP in your PC Bios settings. Connect the power supply and hook up the parallel port to your computer and programmer. b. If you are using a USB port, insert the drive files CD, connect the power supply, and connect the USB cable to the programmer and PC. The PC will detect the new hardware, follow the wizard and search for suitable driver from the CD-ROM. c. Use the programmer arrow buttons to set the programmer LCD display to “TYPE” 2. a. Install CyberClocks or register on-line for SSCG products configuration software, CyberClocks Online, at www.cyberclocksonline.com[2] b. Install the CY3672 software, which is available on Cypress website at www.cypress.com, onto your computer. 3. Use CyberClocks or CyberClocks online to generate a JEDEC file for the device you wish to program. 4. Open up the CY3672 software: go to Start Menu->Programs->Cypress->CY3672 or the location where the software was installed. 5. Double click on the device that you wish to program under the CYPRESS->CyClocksRT menu on the left side of the screen, see Figure 4. 6. Click on the “Start” button at the bottom of the popup window, see Figure 5. 7. Browse to and select the JEDEC file which you created earlier in step 4 and click on “Open”. 8. Click “Yes” when the Upload Message screen pops up. 9. Once you see “Complete...” on the status bar at the bottom of the window click on the “Program IC” icon at the top right of the window (see figure below). 10.When you see a window with “Socket 1... Program OK.” pop up you have successfully programmed a device.[3] Step 10 Step 6 Figure 4. CY3672 Software, Device Selection Page Note: 2. Registration process for the CyberClocks Online: a. Go to CyberClocks Online website b. Fill out the registration form. You need to have a valid e-mail address consists of a work-related e-mail. c. Make sure to check the “non-standard devices” box in the registration form d. Enter your cypress contact person. e. The approval process can take up to 48 hours. f. Upon the approval, the user will receive an e-mail indicating that the request has been successfully processed. 3. For more detailed information on all the functions of the software and programmer, please see the user manual. Document #: 38-07409 Rev. *F Page 3 of 6 CY3672 Step 7 Step 9 Step 11 Figure 5. CY3672 Software, Programming Sequence Document #: 38-07409 Rev. *F Page 4 of 6 CY3672 Sockets To order additional sockets for the other devices listed below, please contact your local Cypress FAE or go to http://www.onfulfillment.com/cypressstore and click on “Timing Technology.” Table 1 below lists the available sockets and their corresponding devices and configuration software. Table 1. Available Sockets Socket Part Number CY3695 CY3696 CY3697 CY3698 CY3699 CY3690 CY3691 CY3692 CY3693 CY3694 CY3613 CY3724 CY3617 CY3618 Socket Label CY3672ADP000 CY3672ADP001 CY3672ADP002 CY3672ADP003 CY3672ADP004 CY3672ADP008 CY3672ADP009 CY3672ADP006 CY3672ADP007 CY3672ADP005 CY3672ADP013 CY3672ADP021 CY3672ADP016 CY3672ADP017 CY25200F CY2077FS CY2077FZ CY22381F CY25100ZCF CY25100SCF CY23FP12 CY26049 CY27EE16 CY25701FJXC CY25701FLXC CY25702FJXC CY25702FXCT Programming Device CY22050F, CY22150F Configuration Software CyberClocks CyberClocks Online CyberClocks CyberClocks CyberClocks CyberClocks Online CyberClocks Online CyberClocks CyberClocks CyberClocks CyberClocks Online CyberClocks Online CyberClocks Online CyberClocks Online CY22392F, CY22393F, CY22394F, CY22395F CyberClocks Ordering Information Ordering Code CY3672 CY3672-PRG CY3672-USB CY3690 CY3691 CY3692 CY3693 CY3694 CY3695 CY3696 CY3697 CY3698 CY3699 CY3613 CY3724 CY3617 CY3618 FTG Programmer FTG Programmer with USB Support CY25100ZCF Socket Adapter (TSSOP) CY25100SCF Socket Adapter (SOIC) CY23FP12 CY26049 CY27EE16 CY22050F, CY22150F, CY25200F CY2077FS CY2077FZ CY22392F, CY22393F, CY22394F, CY22395F CY22381F CY25701FJXC CY25701FLXC CY25702FJXC CY25702FXCT Package description FTG Development Kit Operating Voltage 110V/220V 110V/220V 110V/220V N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Microsoft and Windows are registered trademarks of Microsoft Corporation. CyberClocks and CyClocksRT are trademarks of Cypress Semiconductor Corporation. All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-07409 Rev. *F Page 5 of 6 © Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. CY3672 Document History Page Document Title: CY3672 PTG Programming Kit Document Number: 38-07409 REV. ** *A ECN NO. 114456 118435 Issue Date 07/24/02 12/05/02 Orig. of Change CKN CKN New data sheet Removed CD containing CyClocksRT software, CY3672 programmer interface software, data sheet Added Quick Start Guide under kit contents Updated paragraph two of Functional Description to include information on new software CyberClocks Added CY3690, CY3691, CY3692, CY3693 and CY3694 socket adapters Added Quick Start Guide Added the registration process for the CyberClocks Online Fixed the ordering information to match the DevMaster Added CY25200F Socket Adapter Added CY3613 Socket for CY25701F Device Added CY3617 socket for CY25702FJXC Added CY3618 socket for CY25702FXCT Added CY3672-USB Programmer Information Added CY3724 Socket Adapter for CY25701FLXC Description of Change *B *C *D *E 127454 223822 270030 390555 09/05/03 See ECN See ECN See ECN RGL RGL RGL RGL *F 404668 See ECN RGL Document #: 38-07409 Rev. *F Page 6 of 6